go/tlbmc-onboarding-npis
This document outlines the additions necessary to Entity-Manager (EM) configuration files to onboard an NPI to tlBMC. Entity-Manager provides mappings from hardware components to software components within a system, these mappings are managed through EM configuration files as described here.
Note: tlBMC requires only additions to existing EM config files, no deletions or modifications of existing properties should occur. This allows tlBMC to be backward compatible with existing bmcweb without conflicting behavior. Original design doc can be viewed at go/tlbmc-data-completeness
Tip: Existing daemons, e.g. PSU sensors, will still coexist if not disabled explicitly. Whether these should be configured depends on the use case. If the sensor is only used in telemetry reporting not control, e.g. PID, tlBMC can fully replace existing daemons.
The addition of the ProbeV2 field makes the config detectable by tlBMC. The value of the IpmiFru JSON within the ProbeV2 field corresponds with the existing Probe field in EM configs. BOARD_CONFIG_NAME, PRODUCT_CONFIG_NAME, and BOARD_PART_NUMBER are valid probe fields, and if a scanned FRU matches these fields, the object will be created from this config.
An example definition:
...
"ProbeV2": {
"IpmiFru": {
"BOARD_PRODUCT_NAME": "foo"
}
},
...
The ProbeV2 field can also be set to TRUE to always be populated regardless of matching a scanned FRU, or it can be set to FALSE to be ignored.
An example definition:
... "ProbeV2": "TRUE", ...
Logical AND and OR syntax is supported for the IpmiFru field if given an array of JSON objects instead of a single JSON.
The logical AND operation is applied for all fields within a single IpmiFru JSON. For the matcher to evaluate as True, every field must be a match.
An example definition:
// In this example, the scanned FRU must have both the BOARD_PRODUCT_NAME = foo
// and the BOARD_PART_NUMBER = 1234567890 to successfully probe to True
...
"ProbeV2": {
"IpmiFru": [
{
"BOARD_PRODUCT_NAME": "foo",
"BOARD_PART_NUMBER": "1234567890"
}
]
}
...
The logical OR operation is applied between matcher objects within the array of IpmiFru JSONs. If any one of the matchers evaluates to True, considering the logical AND syntax above, the Probe will be evaluated as True.
An example definition:
// In this example, the scanned FRU must have either the BOARD_PRODUCT_NAME = foo
// or the BOARD_PART_NUMBER = 1234567890 to successfully probe to True. If either
// field matches, the probe will be successful regardless of the value of the other field
...
"ProbeV2": {
"IpmiFru": [
{
"BOARD_PRODUCT_NAME": "foo"
},
{
"BOARD_PART_NUMBER": "1234567890"
}
]
}
...
Note: FOUND behaviors are not yet supported by tlBMC.
ResourceType has parity with the Type field in existing EM configs.
Supported resource types are defined in tlbmc/resource/resource.proto.
An example definition:
... "ResourceType": "RESOURCE_TYPE_BOARD", ...
For configs of RESOURCE_TYPE_BOARD an ChassisType is needed as a additional field. This field has parity with the EM config field xyz.openbmc_project.Inventory.Item.Chassis.ChassisType. This field will default to type RackMount.
Supported chassis types are defined in tlbmc/resource/resource.proto.
An example definition:
... "ChassisType": "CHASSIS_TYPE_COMPONENT", ...
Physical ports are modeled as downstream/upstream ports between Chassis. These are fields in the Exposes array of a config and may correspond to existing ports. Similar to existing EM configs, a port on an upstream chassis to a downstream chassis has a Label field, used to populate the devpath. These ports will have the Type of PortDownstream. On the downstream chassis, there will be a corresponding port with the same name, but the Type will be UpstreamConnection.
Tip: Only one chassis (the root chassis) will have no UpstreamConnection or CableUpstreamConnection. This is enforced by tlBMC and the store will fail to create if this condition is not true.
An example of a PortDownstream port:
"Exposes": [
...
{
"Label": "bar",
"Name": "Foo $bus Port",
"Type": "PortDownstream",
"User": "tlbmc"
},
...
],
and the corresponding UpstreamConnection port:
"Exposes": [
...
{
"Name": "Foo $bus Port",
"Type": "UpstreamConnection",
"User": "tlbmc"
},
...
],
Note: The name field must match exactly between PortDownstream and UpstreamConnection ports. This is how topology is created and contains and contained_by associations are populated.
ConnectorLocationType has parity with the xyz.openbmc_project.Inventory.Connector field in existing EM configs.
ConnectorLocationType should be one of Slot or Bay.
An example definition:
... "ConnectorLocationType": "Slot", ...
Processor is a field unique to tlBMC, since these can no longer be detected through dbus, they must be defined in the static configuration. Processors are defined in the Exposes field of a config, with a Name and "Type": "Processor".
An example definition:
"Exposes": [
...
{
"Name": "cpu0",
"Type": "Processor",
"User": "tlbmc"
},
...
],
Storage has parity with the xyz.openbmc_project.Inventory.Item.Storage field. This field is a JSON with a single Id field. The storage field is used to create the link to the associated Storage object in the redfish query response, the value of Id should be the Id of the associated Storage object.
An example definition:
...
"Storage": {
"Id": "foo_storage_$index"
},
...
Asset has parity with the xyz.openbmc_project.Inventory.Decorator.Asset field in existing EM configs. This field allows users to override the Manufacturer, Model, PartNumber, or SerialNumber in the redfish response. Valid substitutions are defined in the same way as in the OpenBMC definition, for example: $PRODUCT_PART_NUMBER or $BOARD_MANUFACTURER will substitute the respective field from the scanned FRU object. Fields can also be overridden with any string that is not prefixed with $.
Tip: if a substitution is attempted (prefixed with $) but fails, tlBMC will error.
An example definition:
...
"Asset": {
"Manufacturer": "$BOARD_MANUFACTURER",
"Model": "foo",
"PartNumber": "$BOARD_PART_NUMBER",
"SerialNumber": "$BOARD_SERIAL_NUMBER",
"User": "tlbmc"
},
...
Certain FRUs require special handling as they may not be scannable when bmcweb comes up. For this purpose, we have created something called an “Ad-Hoc Fru Scanner”. This will allow you to configure exactly how you want to scan a FRU.
An example is below:
"AdHocFruConfig": {
"name": "AdHocFru",
"i2c_common_config": {
"bus": "4",
"address": "83"
},
"delay_between_reads": "0.001s",
"periodic_scan_config": [
{
"scan_interval": "10s",
"scan_count": 6
},
{
"scan_interval": "60s",
"scan_count": 9
},
{
"scan_interval": "600s",
"scan_count": 5
}
]
}
The proto definition is found here.
NOTE: This must go inside the ProbeV2 Json Object.
There are no specific changes that need to be made to HWMon Sensor configs to be compatible with tlBMC.
Not all sensor types are currently supported by tlBMC, see kSupportedHwmonTempSensorTypes in tlbmc/configs/entity_config_json_impl.cc.
There are no specific changes that need to be made to PSU Sensor configs to be compatible with tlBMC.
Not all sensor types are currently supported by tlBMC, see kSupportedPsuSensorTypes in tlbmc/configs/entity_config_json_impl.cc.
All I2C fans need a corresponding fan controller defined in the EM config that share the bus/address combination as the fans. Without this field, no I2C fans will be populated.
An example definition:
"Exposes": [
...
{
"Address": "0x2c",
"Bus": "34",
"Name": "FAN_CONTROLLER",
"Type": "MAX31790"
},
...
],
For all I2C configs, there must be a JSON Connector field that contains at least Pwm (the index of the fan) and PwmName (name of the PWM Fan sensor). Some configs may already have this present. No other changes are required to make I2C fans compatible with tlBMC.
An example definition:
"Exposes": [
...
{
"Address": "0x2c",
"BindConnector": "fan1_tach_connector",
"Bus": "32",
"Connector": {
"Pwm": 1,
"PwmName": "fan1_pwm"
},
"EntityId": "0x1A",
"EntityInstance": "0x01",
"Index": 1,
"Name": "fan1_tach",
...
}
...
]
RelatedItem is a field unique to tlBMC, since RelatedItem can no longer be detected through dbus calls, they must be defined in the static configuration. The RelatedItem of any sensor must be defined as a RelatedItem JSON object within the sensor config. It contains the fields Id (the redfish Id of the related item) and Type (the ResourceType of the related item). By default, the related item will be the parent chassis object. This field only needs to be overridden in the case that the related item should be a different object e.g. a fan.
An example definition:
"Exposes": [
...
{
...
"Name": "fan1_tach",
"RelatedItem": {
"Id": "Fan1",
"Type": "RESOURCE_TYPE_FAN",
"User": "tlbmc"
},
...
}
...
]
Cables are defined in separate EM config files from their associated Chassis, and are associated through CableDownstreamConnection or CableUpstreamConnection type ports in their Exposes field. All Cable configs should have their ProbeV2 field set to TRUE (since Cables cannot be detected over I2C) and their ResourceType set to RESOURCE_TYPE_CABLE. The associated upstream or downstream Chassis must have a port with the opposite connection type and the same Name to form a connection. Also defined in the exposed port is CableId. This field must match the Name field in the Cable config.
Note: There is a difference between the Name field in the port config (name of the port) and CableId, which should match the Name of a Cable config JSON
An example Cable config:
{
"Exposes": [
{
"Name": "Foo Cable Downstream",
"CableId": "FooCable",
"Type": "CableUpstreamConnection",
"User": "tlbmc"
},
{
"Name": "Foo Cable Upstream",
"CableId": "FooCable",
"Type": "CableDownstreamConnection",
"User": "tlbmc"
}
],
"Name": "FooCable",
"Probe": "xyz.openbmc_project.Network.EthernetInterface({'InterfaceName': '^foo$', 'LinkUp': true})",
"ProbeV2": "TRUE",
"ResourceType": "RESOURCE_TYPE_CABLE",
"Type": "Cable"
}
The upstream chassis exposes a CableDownstreamConnection:
"Exposes": {
...
{
"Name": "Foo Cable Downstream",
"CableId": "FooCable",
"Type": "CableDownstreamConnection",
"User": "tlbmc"
},
...
},
and the downstream chassis exposes a CableUpstreamConnection:
"Exposes": {
...
{
"Name": "Foo Cable Upstream",
"CableId": "FooCable",
"Type": "CableUpstreamConnection",
"User": "tlbmc"
},
...
},