diff --git a/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt b/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt
deleted file mode 100644
index d19885b..0000000
--- a/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt
+++ /dev/null
@@ -1,52 +0,0 @@
-* Actions Semi Owl Clock Management Unit (CMU)
-
-The Actions Semi Owl Clock Management Unit generates and supplies clock
-to various controllers within the SoC. The clock binding described here is
-applicable to S900, S700 and S500 SoC's.
-
-Required Properties:
-
-- compatible: should be one of the following,
-	"actions,s900-cmu"
-	"actions,s700-cmu"
-	"actions,s500-cmu"
-- reg: physical base address of the controller and length of memory mapped
-  region.
-- clocks: Reference to the parent clocks ("hosc", "losc")
-- #clock-cells: should be 1.
-- #reset-cells: should be 1.
-
-Each clock is assigned an identifier, and client nodes can use this identifier
-to specify the clock which they consume.
-
-All available clocks are defined as preprocessor macros in corresponding
-dt-bindings/clock/actions,s900-cmu.h or actions,s700-cmu.h or
-actions,s500-cmu.h header and can be used in device tree sources.
-
-External clocks:
-
-The hosc clock used as input for the plls is generated outside the SoC. It is
-expected that it is defined using standard clock bindings as "hosc".
-
-Actions Semi S900 CMU also requires one more clock:
- - "losc" - internal low frequency oscillator
-
-Example: Clock Management Unit node:
-
-        cmu: clock-controller@e0160000 {
-                compatible = "actions,s900-cmu";
-                reg = <0x0 0xe0160000 0x0 0x1000>;
-                clocks = <&hosc>, <&losc>;
-                #clock-cells = <1>;
-                #reset-cells = <1>;
-        };
-
-Example: UART controller node that consumes clock generated by the clock
-management unit:
-
-        uart: serial@e012a000 {
-                compatible = "actions,s900-uart", "actions,owl-uart";
-                reg = <0x0 0xe012a000 0x0 0x2000>;
-                interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-                clocks = <&cmu CLK_UART5>;
-        };
diff --git a/Documentation/devicetree/bindings/clock/actions,owl-cmu.yaml b/Documentation/devicetree/bindings/clock/actions,owl-cmu.yaml
new file mode 100644
index 0000000..2839644
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/actions,owl-cmu.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/actions,owl-cmu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Actions Semi Owl Clock Management Unit (CMU)
+
+maintainers:
+  - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+description: |
+  The Actions Semi Owl Clock Management Unit generates and supplies clock
+  to various controllers within the SoC.
+
+  See also:
+    include/dt-bindings/clock/actions,s500-cmu.h
+    include/dt-bindings/clock/actions,s700-cmu.h
+    include/dt-bindings/clock/actions,s900-cmu.h
+
+properties:
+  compatible:
+    enum:
+      - actions,s500-cmu
+      - actions,s700-cmu
+      - actions,s900-cmu
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Host oscillator source
+      - description: Internal low frequency oscillator source
+
+  "#clock-cells":
+    const: 1
+
+  "#reset-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - "#clock-cells"
+  - "#reset-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    clock-controller@e0160000 {
+        compatible = "actions,s900-cmu";
+        reg = <0xe0160000 0x1000>;
+        clocks = <&hosc>, <&losc>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };
+...
diff --git a/Documentation/devicetree/bindings/clock/ti/composite.txt b/Documentation/devicetree/bindings/clock/ti/composite.txt
index 6f7e133..238e6f7 100644
--- a/Documentation/devicetree/bindings/clock/ti/composite.txt
+++ b/Documentation/devicetree/bindings/clock/ti/composite.txt
@@ -16,8 +16,8 @@
 "ti,*composite*-clock" types.
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/clock/ti/mux.txt
-[3] Documentation/devicetree/bindings/clock/ti/divider.txt
+[2] Documentation/devicetree/bindings/clock/ti/ti,mux-clock.yaml
+[3] Documentation/devicetree/bindings/clock/ti/ti,divider-clock.yaml
 [4] Documentation/devicetree/bindings/clock/ti/gate.txt
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/clock/ti/divider.txt b/Documentation/devicetree/bindings/clock/ti/divider.txt
deleted file mode 100644
index 4d7c76f..0000000
--- a/Documentation/devicetree/bindings/clock/ti/divider.txt
+++ /dev/null
@@ -1,115 +0,0 @@
-Binding for TI divider clock
-
-This binding uses the common clock binding[1].  It assumes a
-register-mapped adjustable clock rate divider that does not gate and has
-only one input clock or parent.  By default the value programmed into
-the register is one less than the actual divisor value.  E.g:
-
-register value		actual divisor value
-0			1
-1			2
-2			3
-
-This assumption may be modified by the following optional properties:
-
-ti,index-starts-at-one - valid divisor values start at 1, not the default
-of 0.  E.g:
-register value		actual divisor value
-1			1
-2			2
-3			3
-
-ti,index-power-of-two - valid divisor values are powers of two.  E.g:
-register value		actual divisor value
-0			1
-1			2
-2			4
-
-Additionally an array of valid dividers may be supplied like so:
-
-	ti,dividers = <4>, <8>, <0>, <16>;
-
-Which will map the resulting values to a divisor table by their index:
-register value		actual divisor value
-0			4
-1			8
-2			<invalid divisor, skipped>
-3			16
-
-Any zero value in this array means the corresponding bit-value is invalid
-and must not be used.
-
-The binding must also provide the register to control the divider and
-unless the divider array is provided, min and max dividers. Optionally
-the number of bits to shift that mask, if necessary. If the shift value
-is missing it is the same as supplying a zero shift.
-
-This binding can also optionally provide support to the hardware autoidle
-feature, see [2].
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt
-
-Required properties:
-- compatible : shall be "ti,divider-clock" or "ti,composite-divider-clock".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : link to phandle of parent clock
-- reg : offset for register controlling adjustable divider
-
-Optional properties:
-- clock-output-names : from common clock binding.
-- ti,dividers : array of integers defining divisors
-- ti,bit-shift : number of bits to shift the divider value, defaults to 0
-- ti,min-div : min divisor for dividing the input clock rate, only
-  needed if the first divisor is offset from the default value (1)
-- ti,max-div : max divisor for dividing the input clock rate, only needed
-  if ti,dividers is not defined.
-- ti,index-starts-at-one : valid divisor programming starts at 1, not zero,
-  only valid if ti,dividers is not defined.
-- ti,index-power-of-two : valid divisor programming must be a power of two,
-  only valid if ti,dividers is not defined.
-- ti,autoidle-shift : bit shift of the autoidle enable bit for the clock,
-  see [2]
-- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0,
-  see [2]
-- ti,set-rate-parent : clk_set_rate is propagated to parent
-- ti,latch-bit : latch the divider value to HW, only needed if the register
-  access requires this. As an example dra76x DPLL_GMAC H14 divider implements
-  such behavior.
-
-Examples:
-dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 {
-	#clock-cells = <0>;
-	compatible = "ti,divider-clock";
-	clocks = <&dpll_usb_ck>;
-	ti,max-div = <127>;
-	reg = <0x190>;
-	ti,index-starts-at-one;
-};
-
-aess_fclk: aess_fclk@4a004528 {
-	#clock-cells = <0>;
-	compatible = "ti,divider-clock";
-	clocks = <&abe_clk>;
-	ti,bit-shift = <24>;
-	reg = <0x528>;
-	ti,max-div = <2>;
-};
-
-dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck {
-	#clock-cells = <0>;
-	compatible = "ti,composite-divider-clock";
-	clocks = <&dpll_core_x2_ck>;
-	ti,max-div = <31>;
-	reg = <0x0134>;
-	ti,index-starts-at-one;
-};
-
-ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2 {
-	#clock-cells = <0>;
-	compatible = "ti,composite-divider-clock";
-	clocks = <&corex2_fck>;
-	ti,bit-shift = <8>;
-	reg = <0x0a40>;
-	ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
-};
diff --git a/Documentation/devicetree/bindings/clock/ti/interface.txt b/Documentation/devicetree/bindings/clock/ti/interface.txt
deleted file mode 100644
index 85fb1f2..0000000
--- a/Documentation/devicetree/bindings/clock/ti/interface.txt
+++ /dev/null
@@ -1,55 +0,0 @@
-Binding for Texas Instruments interface clock.
-
-This binding uses the common clock binding[1]. This clock is
-quite much similar to the basic gate-clock [2], however,
-it supports a number of additional features, including
-companion clock finding (match corresponding functional gate
-clock) and hardware autoidle enable / disable.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.yaml
-
-Required properties:
-- compatible : shall be one of:
-  "ti,omap3-interface-clock" - basic OMAP3 interface clock
-  "ti,omap3-no-wait-interface-clock" - interface clock which has no hardware
-				       capability for waiting clock to be ready
-  "ti,omap3-hsotgusb-interface-clock" - interface clock with USB specific HW
-					handling
-  "ti,omap3-dss-interface-clock" - interface clock with DSS specific HW handling
-  "ti,omap3-ssi-interface-clock" - interface clock with SSI specific HW handling
-  "ti,am35xx-interface-clock" - interface clock with AM35xx specific HW handling
-  "ti,omap2430-interface-clock" - interface clock with OMAP2430 specific HW
-				  handling
-- #clock-cells : from common clock binding; shall be set to 0
-- clocks : link to phandle of parent clock
-- reg : base address for the control register
-
-Optional properties:
-- clock-output-names : from common clock binding.
-- ti,bit-shift : bit shift for the bit enabling/disabling the clock (default 0)
-
-Examples:
-	aes1_ick: aes1_ick@48004a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x48004a14 0x4>;
-		ti,bit-shift = <3>;
-	};
-
-	cam_ick: cam_ick@48004f10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&l4_ick>;
-		reg = <0x48004f10 0x4>;
-		ti,bit-shift = <0>;
-	};
-
-	ssi_ick_3430es2: ssi_ick_3430es2@48004a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-ssi-interface-clock";
-		clocks = <&ssi_l4_ick>;
-		reg = <0x48004a10 0x4>;
-		ti,bit-shift = <0>;
-	};
diff --git a/Documentation/devicetree/bindings/clock/ti/mux.txt b/Documentation/devicetree/bindings/clock/ti/mux.txt
deleted file mode 100644
index cd56d3c..0000000
--- a/Documentation/devicetree/bindings/clock/ti/mux.txt
+++ /dev/null
@@ -1,78 +0,0 @@
-Binding for TI mux clock.
-
-This binding uses the common clock binding[1].  It assumes a
-register-mapped multiplexer with multiple input clock signals or
-parents, one of which can be selected as output.  This clock does not
-gate or adjust the parent rate via a divider or multiplier.
-
-By default the "clocks" property lists the parents in the same order
-as they are programmed into the register.  E.g:
-
-	clocks = <&foo_clock>, <&bar_clock>, <&baz_clock>;
-
-results in programming the register as follows:
-
-register value		selected parent clock
-0			foo_clock
-1			bar_clock
-2			baz_clock
-
-Some clock controller IPs do not allow a value of zero to be programmed
-into the register, instead indexing begins at 1.  The optional property
-"index-starts-at-one" modified the scheme as follows:
-
-register value		selected clock parent
-1			foo_clock
-2			bar_clock
-3			baz_clock
-
-The binding must provide the register to control the mux. Optionally
-the number of bits to shift the control field in the register can be
-supplied. If the shift value is missing it is the same as supplying
-a zero shift.
-
-[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-Required properties:
-- compatible : shall be "ti,mux-clock" or "ti,composite-mux-clock".
-- #clock-cells : from common clock binding; shall be set to 0.
-- clocks : link phandles of parent clocks
-- reg : register offset for register controlling adjustable mux
-
-Optional properties:
-- clock-output-names : from common clock binding.
-- ti,bit-shift : number of bits to shift the bit-mask, defaults to
-  0 if not present
-- ti,index-starts-at-one : valid input select programming starts at 1, not
-  zero
-- ti,set-rate-parent : clk_set_rate is propagated to parent clock,
-  not supported by the composite-mux-clock subtype
-- ti,latch-bit : latch the mux value to HW, only needed if the register
-  access requires this. As an example, dra7x DPLL_GMAC H14 muxing
-  implements such behavior.
-
-Examples:
-
-sys_clkin_ck: sys_clkin_ck@4a306110 {
-	#clock-cells = <0>;
-	compatible = "ti,mux-clock";
-	clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
-	reg = <0x0110>;
-	ti,index-starts-at-one;
-};
-
-abe_dpll_bypass_clk_mux_ck: abe_dpll_bypass_clk_mux_ck@4a306108 {
-	#clock-cells = <0>;
-	compatible = "ti,mux-clock";
-	clocks = <&sys_clkin_ck>, <&sys_32k_ck>;
-	ti,bit-shift = <24>;
-	reg = <0x0108>;
-};
-
-mcbsp5_mux_fck: mcbsp5_mux_fck {
-	#clock-cells = <0>;
-	compatible = "ti,composite-mux-clock";
-	clocks = <&core_96m_fck>, <&mcbsp_clks>;
-	ti,bit-shift = <4>;
-	reg = <0x02d8>;
-};
diff --git a/Documentation/devicetree/bindings/clock/ti/ti,divider-clock.yaml b/Documentation/devicetree/bindings/clock/ti/ti,divider-clock.yaml
new file mode 100644
index 0000000..3fbe236
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/ti,divider-clock.yaml
@@ -0,0 +1,193 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/ti/ti,divider-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments divider clock
+
+maintainers:
+  - Tero Kristo <kristo@kernel.org>
+
+description: |
+  This clock It assumes a register-mapped adjustable clock rate divider
+  that does not gate and has only one input clock or parent.  By default the
+  value programmed into the register is one less than the actual divisor value.
+  E.g:
+
+  register value    actual divisor value
+  0                 1
+  1                 2
+  2                 3
+
+  This assumption may be modified by the following optional properties:
+
+  ti,index-starts-at-one - valid divisor values start at 1, not the default
+  of 0.  E.g:
+  register value    actual divisor value
+  1                 1
+  2                 2
+  3                 3
+
+  ti,index-power-of-two - valid divisor values are powers of two.  E.g:
+  register value    actual divisor value
+  0                 1
+  1                 2
+  2                 4
+
+  Additionally an array of valid dividers may be supplied like so:
+
+  ti,dividers = <4>, <8>, <0>, <16>;
+
+  Which will map the resulting values to a divisor table by their index:
+  register value    actual divisor value
+  0                 4
+  1                 8
+  2                 <invalid divisor, skipped>
+  3                 16
+
+  Any zero value in this array means the corresponding bit-value is invalid
+  and must not be used.
+
+  The binding must also provide the register to control the divider and
+  unless the divider array is provided, min and max dividers. Optionally
+  the number of bits to shift that mask, if necessary. If the shift value
+  is missing it is the same as supplying a zero shift.
+
+  This binding can also optionally provide support to the hardware autoidle
+  feature, see [1].
+
+  [1] Documentation/devicetree/bindings/clock/ti/autoidle.txt
+
+properties:
+  compatible:
+    enum:
+      - ti,divider-clock
+      - ti,composite-divider-clock
+
+  "#clock-cells":
+    const: 0
+
+  clocks:
+    maxItems: 1
+
+  clock-output-names:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  ti,dividers:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description:
+      array of integers defining divisors
+
+  ti,bit-shift:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      number of bits to shift the divider value
+    maximum: 31
+    default: 0
+
+  ti,min-div:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      min divisor for dividing the input clock rate, only
+      needed if the first divisor is offset from the default value (1)
+    minimum: 1
+    default: 1
+
+
+  ti,max-div:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      max divisor for dividing the input clock rate, only needed
+      if ti,dividers is not defined.
+
+  ti,index-starts-at-one:
+    type: boolean
+    description:
+      valid divisor programming starts at 1, not zero,
+      only valid if ti,dividers is not defined
+
+  ti,index-power-of-two:
+    type: boolean
+    description:
+      valid divisor programming must be a power of two,
+      only valid if ti,dividers is not defined.
+
+  ti,autoidle-shift:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      bit shift of the autoidle enable bit for the clock,
+      see [1].
+    maximum: 31
+    default: 0
+
+  ti,invert-autoidle-bit:
+    type: boolean
+    description:
+      autoidle is enabled by setting the bit to 0,
+      see [1]
+
+  ti,set-rate-parent:
+    type: boolean
+    description:
+      clk_set_rate is propagated to parent            |
+
+  ti,latch-bit:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      latch the divider value to HW, only needed if the register
+      compatible access requires this. As an example dra76x DPLL_GMAC
+      H14 divider implements such behavior.
+
+dependentSchemas:
+  ti,dividers:
+    properties:
+      ti,min-div: false
+      ti,max-div: false
+      ti,index-power-of-two: false
+      ti,index-starts-at-one: false
+
+required:
+  - compatible
+  - "#clock-cells"
+  - clocks
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      clock-controller@190 {
+        #clock-cells = <0>;
+        compatible = "ti,divider-clock";
+        clocks = <&dpll_usb_ck>;
+        ti,max-div = <127>;
+        reg = <0x190>;
+        ti,index-starts-at-one;
+      };
+
+      clock-controller@528 {
+        #clock-cells = <0>;
+        compatible = "ti,divider-clock";
+        clocks = <&abe_clk>;
+        ti,bit-shift = <24>;
+        reg = <0x528>;
+        ti,max-div = <2>;
+      };
+
+      clock-controller@a40 {
+        #clock-cells = <0>;
+        compatible = "ti,composite-divider-clock";
+        clocks = <&corex2_fck>;
+        ti,bit-shift = <8>;
+        reg = <0x0a40>;
+        ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/clock/ti/ti,interface-clock.yaml b/Documentation/devicetree/bindings/clock/ti/ti,interface-clock.yaml
new file mode 100644
index 0000000..1eaf95d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/ti,interface-clock.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/ti/ti,interface-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments interface clock.
+
+maintainers:
+  - Tero Kristo <kristo@kernel.org>
+
+description: |
+  This clock is quite much similar to the basic gate-clock[1], however,
+  it supports a number of additional features, including
+  companion clock finding (match corresponding functional gate
+  clock) and hardware autoidle enable / disable.
+
+  [1] Documentation/devicetree/bindings/clock/gpio-gate-clock.yaml
+
+properties:
+  compatible:
+    enum:
+      - ti,omap3-interface-clock           # basic OMAP3 interface clock
+      - ti,omap3-no-wait-interface-clock   # interface clock which has no hardware
+                                           # capability for waiting clock to be ready
+      - ti,omap3-hsotgusb-interface-clock  # interface clock with USB specific HW handling
+      - ti,omap3-dss-interface-clock       # interface clock with DSS specific HW handling
+      - ti,omap3-ssi-interface-clock       # interface clock with SSI specific HW handling
+      - ti,am35xx-interface-clock          # interface clock with AM35xx specific HW handling
+      - ti,omap2430-interface-clock        # interface clock with OMAP2430 specific HW handling
+
+  "#clock-cells":
+    const: 0
+
+  clocks:
+    maxItems: 1
+
+  clock-output-names:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  ti,bit-shift:
+    description:
+      bit shift for the bit enabling/disabling the clock
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+    maximum: 31
+
+required:
+  - compatible
+  - clocks
+  - '#clock-cells'
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      aes1_ick: clock-controller@3 {
+        #clock-cells = <0>;
+        compatible = "ti,omap3-interface-clock";
+        clocks = <&security_l4_ick2>;
+        reg = <3>;
+      };
+    };
diff --git a/Documentation/devicetree/bindings/clock/ti/ti,mux-clock.yaml b/Documentation/devicetree/bindings/clock/ti/ti,mux-clock.yaml
new file mode 100644
index 0000000..485b6aa
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/ti,mux-clock.yaml
@@ -0,0 +1,125 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/ti/ti,mux-clock.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments mux clock
+
+maintainers:
+  - Tero Kristo <kristo@kernel.org>
+
+description: |
+  This clock assumes a register-mapped multiplexer with multiple inpt clock
+  signals or parents, one of which can be selected as output. This clock does
+  not gate or adjust the parent rate via a divider or multiplier.
+
+  By default the "clocks" property lists the parents in the same order
+  as they are programmed into the register.  E.g:
+
+    clocks = <&foo_clock>, <&bar_clock>, <&baz_clock>;
+
+  Results in programming the register as follows:
+
+  register value   selected parent clock
+  0                foo_clock
+  1                bar_clock
+  2                baz_clock
+
+  Some clock controller IPs do not allow a value of zero to be programmed
+  into the register, instead indexing begins at 1.  The optional property
+  "index-starts-at-one" modified the scheme as follows:
+
+  register value   selected clock parent
+  1                foo_clock
+  2                bar_clock
+  3                baz_clock
+
+  The binding must provide the register to control the mux. Optionally
+  the number of bits to shift the control field in the register can be
+  supplied. If the shift value is missing it is the same as supplying
+  a zero shift.
+
+properties:
+  compatible:
+    enum:
+      - ti,mux-clock
+      - ti,composite-mux-clock
+
+  "#clock-cells":
+    const: 0
+
+  clocks: true
+
+  clock-output-names:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  ti,bit-shift:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Number of bits to shift the bit-mask
+    maximum: 31
+    default: 0
+
+  ti,index-starts-at-one:
+    type: boolean
+    description:
+      Valid input select programming starts at 1, not zero
+
+  ti,set-rate-parent:
+    type: boolean
+    description:
+      clk_set_rate is propagated to parent clock,
+      not supported by the composite-mux-clock subtype.
+
+  ti,latch-bit:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Latch the mux value to HW, only needed if the register
+      access requires this. As an example, dra7x DPLL_GMAC H14 muxing
+      implements such behavior.
+    maximum: 31
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: ti,composite-mux-clock
+then:
+  properties:
+    ti,set-rate-parent: false
+
+required:
+  - compatible
+  - "#clock-cells"
+  - clocks
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      clock-controller@110 {
+        compatible = "ti,mux-clock";
+        reg = <0x0110>;
+        #clock-cells = <0>;
+        clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>;
+        ti,index-starts-at-one;
+        ti,set-rate-parent;
+      };
+
+      clock-controller@120 {
+        compatible = "ti,composite-mux-clock";
+        reg = <0x0120>;
+        #clock-cells = <0>;
+        clocks = <&core_96m_fck>, <&mcbsp_clks>;
+        ti,bit-shift = <4>;
+      };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index c27f319..0e2489f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1996,7 +1996,7 @@
 L:	linux-actions@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	Documentation/devicetree/bindings/arm/actions.yaml
-F:	Documentation/devicetree/bindings/clock/actions,owl-cmu.txt
+F:	Documentation/devicetree/bindings/clock/actions,owl-cmu.yaml
 F:	Documentation/devicetree/bindings/dma/owl-dma.yaml
 F:	Documentation/devicetree/bindings/i2c/i2c-owl.yaml
 F:	Documentation/devicetree/bindings/interrupt-controller/actions,owl-sirq.yaml