# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/gpio/xlnx,gpio-xilinx.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Xilinx AXI GPIO controller

maintainers:
  - Neeli Srinivas <srinivas.neeli@amd.com>

description:
  The AXI GPIO design provides a general purpose input/output interface
  to an AXI4-Lite interface. The AXI GPIO can be configured as either
  a single or a dual-channel device. The width of each channel is
  independently configurable. The channels can be configured to
  generate an interrupt when a transition on any of their inputs occurs.

properties:
  compatible:
    enum:
      - xlnx,xps-gpio-1.00.a

  reg:
    maxItems: 1

  "#gpio-cells":
    const: 2

  interrupts:
    maxItems: 1

  gpio-controller: true

  gpio-line-names:
    description: strings describing the names of each gpio line
    minItems: 1
    maxItems: 64

  interrupt-controller: true

  "#interrupt-cells":
    const: 2

  clocks:
    maxItems: 1

  interrupt-names: true

  xlnx,all-inputs:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This option sets this GPIO channel1 bits in input mode.

  xlnx,all-inputs-2:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This option sets this GPIO channel2 bits in input mode.

  xlnx,all-outputs:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This option sets this GPIO channel1 bits in output mode.

  xlnx,all-outputs-2:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This option sets this GPIO channel2 bits in output mode.

  xlnx,dout-default:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: Sets the default value of all the enabled bits of
                 channel1.
    default: 0

  xlnx,dout-default-2:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: Sets the default value of all the enabled bits of
                 channel2.
    default: 0

  xlnx,gpio-width:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: The value defines the bit width of the GPIO channel1.
    minimum: 1
    maximum: 32
    default: 32

  xlnx,gpio2-width:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: The value defines the bit width of the GPIO channel2.
    minimum: 1
    maximum: 32
    default: 32

  xlnx,interrupt-present:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This parameter enables interrupt control logic
                 and interrupt registers in GPIO module.
    minimum: 0
    maximum: 1
    default: 0

  xlnx,is-dual:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This parameter enables a second GPIO channel (GPIO2).
    minimum: 0
    maximum: 1
    default: 0

  xlnx,tri-default:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This value configures the input or output mode
                 of each bit of GPIO channel1.

  xlnx,tri-default-2:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: This value configures the input or output mode
                 of each bit of GPIO channel2.

required:
  - reg
  - compatible
  - clocks
  - gpio-controller
  - "#gpio-cells"

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>

    gpio@a0020000 {
        compatible = "xlnx,xps-gpio-1.00.a";
        reg = <0xa0020000 0x10000>;
        #gpio-cells = <2>;
        #interrupt-cells = <0x2>;
        clocks = <&zynqmp_clk 71>;
        gpio-controller;
        interrupt-controller;
        interrupt-names = "ip2intc_irpt";
        interrupt-parent = <&gic>;
        interrupts = <0 89 4>;
        xlnx,all-inputs = <0x0>;
        xlnx,all-inputs-2 = <0x0>;
        xlnx,all-outputs = <0x0>;
        xlnx,all-outputs-2 = <0x0>;
        xlnx,dout-default = <0x0>;
        xlnx,dout-default-2 = <0x0>;
        xlnx,gpio-width = <0x20>;
        xlnx,gpio2-width = <0x20>;
        xlnx,interrupt-present = <0x1>;
        xlnx,is-dual = <0x1>;
        xlnx,tri-default = <0xFFFFFFFF>;
        xlnx,tri-default-2 = <0xFFFFFFFF>;
    };

...