# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/ufs/rockchip,rk3576-ufshc.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Rockchip UFS Host Controller

maintainers:
  - Shawn Lin <shawn.lin@rock-chips.com>

allOf:
  - $ref: ufs-common.yaml

properties:
  compatible:
    const: rockchip,rk3576-ufshc

  reg:
    maxItems: 5

  reg-names:
    items:
      - const: hci
      - const: mphy
      - const: hci_grf
      - const: mphy_grf
      - const: hci_apb

  clocks:
    maxItems: 4

  clock-names:
    items:
      - const: core
      - const: pclk
      - const: pclk_mphy
      - const: ref_out

  power-domains:
    maxItems: 1

  resets:
    maxItems: 4

  reset-names:
    items:
      - const: biu
      - const: sys
      - const: ufs
      - const: grf

  reset-gpios:
    maxItems: 1
    description: |
      GPIO specifiers for host to reset the whole UFS device including PHY and
      memory. This gpio is active low and should choose the one whose high output
      voltage is lower than 1.5V based on the UFS spec.

required:
  - compatible
  - reg
  - reg-names
  - clocks
  - clock-names
  - interrupts
  - power-domains
  - resets
  - reset-names
  - reset-gpios

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/clock/rockchip,rk3576-cru.h>
    #include <dt-bindings/reset/rockchip,rk3576-cru.h>
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/power/rockchip,rk3576-power.h>
    #include <dt-bindings/pinctrl/rockchip.h>
    #include <dt-bindings/gpio/gpio.h>

    soc {
        #address-cells = <2>;
        #size-cells = <2>;

        ufshc: ufshc@2a2d0000 {
            compatible = "rockchip,rk3576-ufshc";
            reg = <0x0 0x2a2d0000 0x0 0x10000>,
                  <0x0 0x2b040000 0x0 0x10000>,
                  <0x0 0x2601f000 0x0 0x1000>,
                  <0x0 0x2603c000 0x0 0x1000>,
                  <0x0 0x2a2e0000 0x0 0x10000>;
            reg-names = "hci", "mphy", "hci_grf", "mphy_grf", "hci_apb";
            clocks = <&cru ACLK_UFS_SYS>, <&cru PCLK_USB_ROOT>, <&cru PCLK_MPHY>,
                     <&cru CLK_REF_UFS_CLKOUT>;
            clock-names = "core", "pclk", "pclk_mphy", "ref_out";
            interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
            power-domains = <&power RK3576_PD_USB>;
            resets = <&cru SRST_A_UFS_BIU>, <&cru SRST_A_UFS_SYS>, <&cru SRST_A_UFS>,
                     <&cru SRST_P_UFS_GRF>;
            reset-names = "biu", "sys", "ufs", "grf";
            reset-gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>;
        };
    };