| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Synopsys DWC Ethernet Quality-of-Service v4.10a linux driver |
| * |
| * Copyright (C) 2016 Joao Pinto <jpinto@synopsys.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/device.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/ethtool.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/ioport.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_net.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/platform_device.h> |
| #include <linux/reset.h> |
| #include <linux/stmmac.h> |
| |
| #include "stmmac_platform.h" |
| #include "dwmac4.h" |
| |
| struct tegra_eqos { |
| struct device *dev; |
| void __iomem *regs; |
| |
| struct reset_control *rst; |
| |
| struct gpio_desc *reset; |
| }; |
| |
| static int dwc_eth_dwmac_config_dt(struct platform_device *pdev, |
| struct plat_stmmacenet_data *plat_dat) |
| { |
| struct device *dev = &pdev->dev; |
| u32 burst_map = 0; |
| u32 bit_index = 0; |
| u32 a_index = 0; |
| |
| if (!plat_dat->axi) { |
| plat_dat->axi = devm_kzalloc(&pdev->dev, |
| sizeof(struct stmmac_axi), |
| GFP_KERNEL); |
| |
| if (!plat_dat->axi) |
| return -ENOMEM; |
| } |
| |
| plat_dat->axi->axi_lpi_en = device_property_read_bool(dev, |
| "snps,en-lpi"); |
| if (device_property_read_u32(dev, "snps,write-requests", |
| &plat_dat->axi->axi_wr_osr_lmt)) { |
| /** |
| * Since the register has a reset value of 1, if property |
| * is missing, default to 1. |
| */ |
| plat_dat->axi->axi_wr_osr_lmt = 1; |
| } else { |
| /** |
| * If property exists, to keep the behavior from dwc_eth_qos, |
| * subtract one after parsing. |
| */ |
| plat_dat->axi->axi_wr_osr_lmt--; |
| } |
| |
| if (device_property_read_u32(dev, "snps,read-requests", |
| &plat_dat->axi->axi_rd_osr_lmt)) { |
| /** |
| * Since the register has a reset value of 1, if property |
| * is missing, default to 1. |
| */ |
| plat_dat->axi->axi_rd_osr_lmt = 1; |
| } else { |
| /** |
| * If property exists, to keep the behavior from dwc_eth_qos, |
| * subtract one after parsing. |
| */ |
| plat_dat->axi->axi_rd_osr_lmt--; |
| } |
| device_property_read_u32(dev, "snps,burst-map", &burst_map); |
| |
| /* converts burst-map bitmask to burst array */ |
| for (bit_index = 0; bit_index < 7; bit_index++) { |
| if (burst_map & (1 << bit_index)) { |
| switch (bit_index) { |
| case 0: |
| plat_dat->axi->axi_blen[a_index] = 4; break; |
| case 1: |
| plat_dat->axi->axi_blen[a_index] = 8; break; |
| case 2: |
| plat_dat->axi->axi_blen[a_index] = 16; break; |
| case 3: |
| plat_dat->axi->axi_blen[a_index] = 32; break; |
| case 4: |
| plat_dat->axi->axi_blen[a_index] = 64; break; |
| case 5: |
| plat_dat->axi->axi_blen[a_index] = 128; break; |
| case 6: |
| plat_dat->axi->axi_blen[a_index] = 256; break; |
| default: |
| break; |
| } |
| a_index++; |
| } |
| } |
| |
| /* dwc-qos needs GMAC4, AAL, TSO and PMT */ |
| plat_dat->has_gmac4 = 1; |
| plat_dat->dma_cfg->aal = 1; |
| plat_dat->flags |= STMMAC_FLAG_TSO_EN; |
| plat_dat->pmt = 1; |
| |
| return 0; |
| } |
| |
| static int dwc_qos_probe(struct platform_device *pdev, |
| struct plat_stmmacenet_data *plat_dat, |
| struct stmmac_resources *stmmac_res) |
| { |
| plat_dat->pclk = stmmac_pltfr_find_clk(plat_dat, "phy_ref_clk"); |
| |
| return 0; |
| } |
| |
| #define SDMEMCOMPPADCTRL 0x8800 |
| #define SDMEMCOMPPADCTRL_PAD_E_INPUT_OR_E_PWRD BIT(31) |
| |
| #define AUTO_CAL_CONFIG 0x8804 |
| #define AUTO_CAL_CONFIG_START BIT(31) |
| #define AUTO_CAL_CONFIG_ENABLE BIT(29) |
| |
| #define AUTO_CAL_STATUS 0x880c |
| #define AUTO_CAL_STATUS_ACTIVE BIT(31) |
| |
| static void tegra_eqos_fix_speed(void *bsp_priv, int speed, unsigned int mode) |
| { |
| struct tegra_eqos *eqos = bsp_priv; |
| bool needs_calibration = false; |
| struct stmmac_priv *priv; |
| u32 value; |
| int err; |
| |
| switch (speed) { |
| case SPEED_1000: |
| case SPEED_100: |
| needs_calibration = true; |
| fallthrough; |
| |
| case SPEED_10: |
| break; |
| |
| default: |
| dev_err(eqos->dev, "invalid speed %d\n", speed); |
| break; |
| } |
| |
| if (needs_calibration) { |
| priv = netdev_priv(dev_get_drvdata(eqos->dev)); |
| |
| /* Calibration should be done with the MDIO bus idle */ |
| mutex_lock(&priv->mii->mdio_lock); |
| |
| /* calibrate */ |
| value = readl(eqos->regs + SDMEMCOMPPADCTRL); |
| value |= SDMEMCOMPPADCTRL_PAD_E_INPUT_OR_E_PWRD; |
| writel(value, eqos->regs + SDMEMCOMPPADCTRL); |
| |
| udelay(1); |
| |
| value = readl(eqos->regs + AUTO_CAL_CONFIG); |
| value |= AUTO_CAL_CONFIG_START | AUTO_CAL_CONFIG_ENABLE; |
| writel(value, eqos->regs + AUTO_CAL_CONFIG); |
| |
| err = readl_poll_timeout_atomic(eqos->regs + AUTO_CAL_STATUS, |
| value, |
| value & AUTO_CAL_STATUS_ACTIVE, |
| 1, 10); |
| if (err < 0) { |
| dev_err(eqos->dev, "calibration did not start\n"); |
| goto failed; |
| } |
| |
| err = readl_poll_timeout_atomic(eqos->regs + AUTO_CAL_STATUS, |
| value, |
| (value & AUTO_CAL_STATUS_ACTIVE) == 0, |
| 20, 200); |
| if (err < 0) { |
| dev_err(eqos->dev, "calibration didn't finish\n"); |
| goto failed; |
| } |
| |
| failed: |
| value = readl(eqos->regs + SDMEMCOMPPADCTRL); |
| value &= ~SDMEMCOMPPADCTRL_PAD_E_INPUT_OR_E_PWRD; |
| writel(value, eqos->regs + SDMEMCOMPPADCTRL); |
| |
| mutex_unlock(&priv->mii->mdio_lock); |
| } else { |
| value = readl(eqos->regs + AUTO_CAL_CONFIG); |
| value &= ~AUTO_CAL_CONFIG_ENABLE; |
| writel(value, eqos->regs + AUTO_CAL_CONFIG); |
| } |
| } |
| |
| static int tegra_eqos_probe(struct platform_device *pdev, |
| struct plat_stmmacenet_data *plat_dat, |
| struct stmmac_resources *res) |
| { |
| struct device *dev = &pdev->dev; |
| struct tegra_eqos *eqos; |
| int err; |
| |
| eqos = devm_kzalloc(&pdev->dev, sizeof(*eqos), GFP_KERNEL); |
| if (!eqos) |
| return -ENOMEM; |
| |
| eqos->dev = &pdev->dev; |
| eqos->regs = res->addr; |
| |
| if (!is_of_node(dev->fwnode)) |
| goto bypass_clk_reset_gpio; |
| |
| plat_dat->clk_tx_i = stmmac_pltfr_find_clk(plat_dat, "tx"); |
| |
| eqos->reset = devm_gpiod_get(&pdev->dev, "phy-reset", GPIOD_OUT_HIGH); |
| if (IS_ERR(eqos->reset)) { |
| err = PTR_ERR(eqos->reset); |
| return err; |
| } |
| |
| usleep_range(2000, 4000); |
| gpiod_set_value(eqos->reset, 0); |
| |
| /* MDIO bus was already reset just above */ |
| plat_dat->mdio_bus_data->needs_reset = false; |
| |
| eqos->rst = devm_reset_control_get(&pdev->dev, "eqos"); |
| if (IS_ERR(eqos->rst)) { |
| err = PTR_ERR(eqos->rst); |
| goto reset_phy; |
| } |
| |
| err = reset_control_assert(eqos->rst); |
| if (err < 0) |
| goto reset_phy; |
| |
| usleep_range(2000, 4000); |
| |
| err = reset_control_deassert(eqos->rst); |
| if (err < 0) |
| goto reset_phy; |
| |
| usleep_range(2000, 4000); |
| |
| bypass_clk_reset_gpio: |
| plat_dat->fix_mac_speed = tegra_eqos_fix_speed; |
| plat_dat->set_clk_tx_rate = stmmac_set_clk_tx_rate; |
| plat_dat->bsp_priv = eqos; |
| plat_dat->flags |= STMMAC_FLAG_SPH_DISABLE | |
| STMMAC_FLAG_EN_TX_LPI_CLK_PHY_CAP; |
| |
| return 0; |
| |
| reset_phy: |
| gpiod_set_value(eqos->reset, 1); |
| |
| return err; |
| } |
| |
| static void tegra_eqos_remove(struct platform_device *pdev) |
| { |
| struct tegra_eqos *eqos = get_stmmac_bsp_priv(&pdev->dev); |
| |
| reset_control_assert(eqos->rst); |
| gpiod_set_value(eqos->reset, 1); |
| } |
| |
| struct dwc_eth_dwmac_data { |
| int (*probe)(struct platform_device *pdev, |
| struct plat_stmmacenet_data *plat_dat, |
| struct stmmac_resources *res); |
| void (*remove)(struct platform_device *pdev); |
| const char *stmmac_clk_name; |
| }; |
| |
| static const struct dwc_eth_dwmac_data dwc_qos_data = { |
| .probe = dwc_qos_probe, |
| .stmmac_clk_name = "apb_pclk", |
| }; |
| |
| static const struct dwc_eth_dwmac_data tegra_eqos_data = { |
| .probe = tegra_eqos_probe, |
| .remove = tegra_eqos_remove, |
| .stmmac_clk_name = "slave_bus", |
| }; |
| |
| static const struct dwc_eth_dwmac_data fsd_eqos_data = { |
| .stmmac_clk_name = "slave_bus", |
| }; |
| |
| static int dwc_eth_dwmac_probe(struct platform_device *pdev) |
| { |
| const struct dwc_eth_dwmac_data *data; |
| struct plat_stmmacenet_data *plat_dat; |
| struct stmmac_resources stmmac_res; |
| int ret; |
| |
| data = device_get_match_data(&pdev->dev); |
| |
| memset(&stmmac_res, 0, sizeof(struct stmmac_resources)); |
| |
| /** |
| * Since stmmac_platform supports name IRQ only, basic platform |
| * resource initialization is done in the glue logic. |
| */ |
| stmmac_res.irq = platform_get_irq(pdev, 0); |
| if (stmmac_res.irq < 0) |
| return stmmac_res.irq; |
| stmmac_res.wol_irq = stmmac_res.irq; |
| |
| stmmac_res.addr = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(stmmac_res.addr)) |
| return PTR_ERR(stmmac_res.addr); |
| |
| plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac); |
| if (IS_ERR(plat_dat)) |
| return PTR_ERR(plat_dat); |
| |
| ret = devm_clk_bulk_get_all(&pdev->dev, &plat_dat->clks); |
| if (ret < 0) |
| return dev_err_probe(&pdev->dev, ret, "Failed to retrieve all required clocks\n"); |
| plat_dat->num_clks = ret; |
| |
| ret = clk_bulk_prepare_enable(plat_dat->num_clks, plat_dat->clks); |
| if (ret) |
| return dev_err_probe(&pdev->dev, ret, "Failed to enable clocks\n"); |
| |
| plat_dat->stmmac_clk = stmmac_pltfr_find_clk(plat_dat, |
| data->stmmac_clk_name); |
| |
| if (data->probe) |
| ret = data->probe(pdev, plat_dat, &stmmac_res); |
| if (ret < 0) { |
| dev_err_probe(&pdev->dev, ret, "failed to probe subdriver\n"); |
| clk_bulk_disable_unprepare(plat_dat->num_clks, plat_dat->clks); |
| return ret; |
| } |
| |
| ret = dwc_eth_dwmac_config_dt(pdev, plat_dat); |
| if (ret) |
| goto remove; |
| |
| ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); |
| if (ret) |
| goto remove; |
| |
| return ret; |
| |
| remove: |
| if (data->remove) |
| data->remove(pdev); |
| |
| return ret; |
| } |
| |
| static void dwc_eth_dwmac_remove(struct platform_device *pdev) |
| { |
| const struct dwc_eth_dwmac_data *data = device_get_match_data(&pdev->dev); |
| struct plat_stmmacenet_data *plat_dat = dev_get_platdata(&pdev->dev); |
| |
| stmmac_dvr_remove(&pdev->dev); |
| |
| if (data->remove) |
| data->remove(pdev); |
| |
| if (plat_dat) |
| clk_bulk_disable_unprepare(plat_dat->num_clks, plat_dat->clks); |
| } |
| |
| static const struct of_device_id dwc_eth_dwmac_match[] = { |
| { .compatible = "snps,dwc-qos-ethernet-4.10", .data = &dwc_qos_data }, |
| { .compatible = "nvidia,tegra186-eqos", .data = &tegra_eqos_data }, |
| { .compatible = "tesla,fsd-ethqos", .data = &fsd_eqos_data }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, dwc_eth_dwmac_match); |
| |
| static struct platform_driver dwc_eth_dwmac_driver = { |
| .probe = dwc_eth_dwmac_probe, |
| .remove = dwc_eth_dwmac_remove, |
| .driver = { |
| .name = "dwc-eth-dwmac", |
| .pm = &stmmac_pltfr_pm_ops, |
| .of_match_table = dwc_eth_dwmac_match, |
| }, |
| }; |
| module_platform_driver(dwc_eth_dwmac_driver); |
| |
| MODULE_AUTHOR("Joao Pinto <jpinto@synopsys.com>"); |
| MODULE_DESCRIPTION("Synopsys DWC Ethernet Quality-of-Service v4.10a driver"); |
| MODULE_LICENSE("GPL v2"); |