| // SPDX-License-Identifier: GPL-2.0-only | |
| /* Copyright (c) 2013, The Linux Foundation. All rights reserved. | |
| * Copyright (c) 2015, Sony Mobile Communications Inc. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/slab.h> | |
| #include <linux/of.h> | |
| #include <linux/regmap.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/spmi.h> | |
| struct qcom_coincell { | |
| struct device *dev; | |
| struct regmap *regmap; | |
| }; | |
| #define QCOM_COINCELL_REG_RSET 0x44 | |
| #define QCOM_COINCELL_REG_VSET 0x45 | |
| #define QCOM_COINCELL_REG_ENABLE 0x46 | |
| #define QCOM_COINCELL_ENABLE BIT(7) | |
| static const int qcom_rset_map[] = { 2100, 1700, 1200, 800 }; | |
| static const int qcom_vset_map[] = { 2500, 3200, 3100, 3000 }; | |
| /* NOTE: for pm8921 and others, voltage of 2500 is 16 (10000b), not 0 */ | |
| /* if enable==0, rset and vset are ignored */ | |
| static int qcom_coincell_chgr_config(struct qcom_coincell *chgr, int rset, | |
| int vset, bool enable) | |
| { | |
| int i, j, rc; | |
| /* if disabling, just do that and skip other operations */ | |
| if (!enable) | |
| return regmap_write(chgr->regmap, | |
| QCOM_COINCELL_REG_ENABLE, 0); | |
| /* find index for current-limiting resistor */ | |
| for (i = 0; i < ARRAY_SIZE(qcom_rset_map); i++) | |
| if (rset == qcom_rset_map[i]) | |
| break; | |
| if (i >= ARRAY_SIZE(qcom_rset_map)) { | |
| dev_err(chgr->dev, "invalid rset-ohms value %d\n", rset); | |
| return -EINVAL; | |
| } | |
| /* find index for charge voltage */ | |
| for (j = 0; j < ARRAY_SIZE(qcom_vset_map); j++) | |
| if (vset == qcom_vset_map[j]) | |
| break; | |
| if (j >= ARRAY_SIZE(qcom_vset_map)) { | |
| dev_err(chgr->dev, "invalid vset-millivolts value %d\n", vset); | |
| return -EINVAL; | |
| } | |
| rc = regmap_write(chgr->regmap, | |
| QCOM_COINCELL_REG_RSET, i); | |
| if (rc) { | |
| /* | |
| * This is mainly to flag a bad base_addr (reg) from dts. | |
| * Other failures writing to the registers should be | |
| * extremely rare, or indicative of problems that | |
| * should be reported elsewhere (eg. spmi failure). | |
| */ | |
| dev_err(chgr->dev, "could not write to RSET register\n"); | |
| return rc; | |
| } | |
| rc = regmap_write(chgr->regmap, | |
| QCOM_COINCELL_REG_VSET, j); | |
| if (rc) | |
| return rc; | |
| /* set 'enable' register */ | |
| return regmap_write(chgr->regmap, | |
| QCOM_COINCELL_REG_ENABLE, | |
| QCOM_COINCELL_ENABLE); | |
| } | |
| static int qcom_coincell_probe(struct platform_device *pdev) | |
| { | |
| struct regmap_config qcom_coincell_regmap_config = { | |
| .reg_bits = 16, | |
| .val_bits = 8, | |
| .max_register = 0xff, | |
| .fast_io = true, | |
| }; | |
| struct device *dev = &pdev->dev; | |
| struct device_node *node = dev->of_node; | |
| struct spmi_subdevice *sub_sdev; | |
| struct spmi_device *sparent; | |
| struct qcom_coincell chgr; | |
| u32 rset = 0; | |
| u32 vset = 0; | |
| bool enable; | |
| int rc; | |
| chgr.dev = &pdev->dev; | |
| rc = device_property_read_u32(dev, "reg", &qcom_coincell_regmap_config.reg_base); | |
| if (rc) | |
| return rc; | |
| sparent = spmi_get_parent_spmi_device(dev); | |
| if (!sparent) | |
| return -ENODEV; | |
| sub_sdev = devm_spmi_subdevice_alloc_and_add(dev, sparent); | |
| if (IS_ERR(sub_sdev)) | |
| return PTR_ERR(sub_sdev); | |
| chgr.regmap = devm_regmap_init_spmi_ext(&sub_sdev->sdev, | |
| &qcom_coincell_regmap_config); | |
| if (IS_ERR(chgr.regmap)) { | |
| dev_err(chgr.dev, "Unable to get regmap\n"); | |
| return PTR_ERR(chgr.regmap); | |
| } | |
| enable = !of_property_read_bool(node, "qcom,charger-disable"); | |
| if (enable) { | |
| rc = of_property_read_u32(node, "qcom,rset-ohms", &rset); | |
| if (rc) { | |
| dev_err(chgr.dev, | |
| "can't find 'qcom,rset-ohms' in DT block"); | |
| return rc; | |
| } | |
| rc = of_property_read_u32(node, "qcom,vset-millivolts", &vset); | |
| if (rc) { | |
| dev_err(chgr.dev, | |
| "can't find 'qcom,vset-millivolts' in DT block"); | |
| return rc; | |
| } | |
| } | |
| return qcom_coincell_chgr_config(&chgr, rset, vset, enable); | |
| } | |
| static const struct of_device_id qcom_coincell_match_table[] = { | |
| { .compatible = "qcom,pm8941-coincell" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, qcom_coincell_match_table); | |
| static struct platform_driver qcom_coincell_driver = { | |
| .driver = { | |
| .name = "qcom-spmi-coincell", | |
| .of_match_table = qcom_coincell_match_table, | |
| }, | |
| .probe = qcom_coincell_probe, | |
| }; | |
| module_platform_driver(qcom_coincell_driver); | |
| MODULE_DESCRIPTION("Qualcomm PMIC coincell charger driver"); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_IMPORT_NS("SPMI"); |