arch/arm/boot/dts/imx6q-apalis-ixora.dts

// SPDX-License-Identifier: GPL-2.0+ OR MIT
/*
 * Copyright 2014-2020 Toradex
 * Copyright 2012 Freescale Semiconductor, Inc.
 * Copyright 2011 Linaro Ltd.
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include "imx6q.dtsi"
#include "imx6qdl-apalis.dtsi"

/ {
	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board";
	compatible = "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
		     "fsl,imx6q";

	aliases {
		i2c0 = &i2c1;
		i2c1 = &i2c3;
		i2c2 = &i2c2;
		rtc0 = &rtc_i2c;
		rtc1 = &snvs_rtc;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	gpio-keys {
		compatible = "gpio-keys";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_gpio_keys>;

		wakeup {
			label = "Wake-Up";
			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_WAKEUP>;
			debounce-interval = <10>;
			wakeup-source;
		};
	};

	lcd_display: disp0 {
		compatible = "fsl,imx-parallel-display";
		#address-cells = <1>;
		#size-cells = <0>;
		interface-pix-fmt = "rgb24";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
		status = "okay";

		port@0 {
			reg = <0>;

			lcd_display_in: endpoint {
				remote-endpoint = <&ipu1_di1_disp1>;
			};
		};

		port@1 {
			reg = <1>;

			lcd_display_out: endpoint {
				remote-endpoint = <&lcd_panel_in>;
			};
		};
	};

	panel: panel {
		/*
		 * edt,et057090dhu: EDT 5.7" LCD TFT
		 * edt,et070080dh6: EDT 7.0" LCD TFT
		 */
		compatible = "edt,et057090dhu";
		backlight = <&backlight>;

		port {
			lcd_panel_in: endpoint {
				remote-endpoint = <&lcd_display_out>;
			};
		};
	};

	leds {
		compatible = "gpio-leds";

		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_leds_ixora>;

		led4-green {
			label = "LED_4_GREEN";
			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
		};

		led4-red {
			label = "LED_4_RED";
			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
		};

		led5-green {
			label = "LED_5_GREEN";
			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
		};

		led5-red {
			label = "LED_5_RED";
			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
		};
	};
};

&backlight {
	brightness-levels = <0 127 191 223 239 247 251 255>;
	default-brightness-level = <1>;
	status = "okay";
};

&can1 {
	status = "okay";
};

&can2 {
	status = "okay";
};

&hdmi {
	status = "okay";
};

/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
&i2c1 {
	status = "okay";

	/*
	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
	 */
	touchscreen@4a {
		compatible = "atmel,maxtouch";
		reg = <0x4a>;
		interrupt-parent = <&gpio6>;
		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
		status = "disabled";
	};

	eeprom@50 {
		compatible = "atmel,24c02";
		reg = <0x50>;
	};

	/* M41T0M6 real time clock on carrier board */
	rtc_i2c: rtc@68 {
		compatible = "st,m41t0";
		reg = <0x68>;
	};
};

/*
 * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
 * board)
 */
&i2c3 {
	status = "okay";
};

&ipu1_di1_disp1 {
	remote-endpoint = <&lcd_display_in>;
};

&ldb {
	status = "okay";
};

&pcie {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_reset_moci>;
	/* active-high meaning opposite of regular PERST# active-low polarity */
	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
	reset-gpio-active-high;
	status = "okay";
};

&pwm1 {
	status = "okay";
};

&pwm2 {
	status = "okay";
};

&pwm3 {
	status = "okay";
};

&pwm4 {
	status = "okay";
};

&reg_usb_otg_vbus {
	status = "okay";
};

&reg_usb_host_vbus {
	status = "okay";
};

&sata {
	status = "okay";
};

&sound_spdif {
	status = "okay";
};

&spdif {
	status = "okay";
};

&uart1 {
	status = "okay";
};

&uart2 {
	status = "okay";
};

&uart4 {
	status = "okay";
};

&uart5 {
	status = "okay";
};

&usbh1 {
	vbus-supply = <&reg_usb_host_vbus>;
	status = "okay";
};

&usbotg {
	vbus-supply = <&reg_usb_otg_vbus>;
	status = "okay";
};

/* SD1 */
&usdhc2 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
	status = "okay";
};

&iomuxc {
	/* Mux the Apalis GPIOs */
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
		    >;

	pinctrl_leds_ixora: ledsixoragrp {
		fsl,pins = <
			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x1b0b0
			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
		>;
	};
};