| // SPDX-License-Identifier: GPL-2.0-only | 
 | /* | 
 |  * Copyright (C) 2014-2017 Broadcom | 
 |  */ | 
 |  | 
 | /* | 
 |  * This file contains the Broadcom Iproc GPIO driver that supports 3 | 
 |  * GPIO controllers on Iproc including the ASIU GPIO controller, the | 
 |  * chipCommonG GPIO controller, and the always-on GPIO controller. Basic | 
 |  * PINCONF such as bias pull up/down, and drive strength are also supported | 
 |  * in this driver. | 
 |  * | 
 |  * It provides the functionality where pins from the GPIO can be | 
 |  * individually muxed to GPIO function, if individual pad | 
 |  * configuration is supported, through the interaction with respective | 
 |  * SoCs IOMUX controller. | 
 |  */ | 
 |  | 
 | #include <linux/gpio/driver.h> | 
 | #include <linux/interrupt.h> | 
 | #include <linux/io.h> | 
 | #include <linux/ioport.h> | 
 | #include <linux/kernel.h> | 
 | #include <linux/of_device.h> | 
 | #include <linux/of_irq.h> | 
 | #include <linux/seq_file.h> | 
 | #include <linux/slab.h> | 
 |  | 
 | #include <linux/pinctrl/consumer.h> | 
 | #include <linux/pinctrl/pinconf-generic.h> | 
 | #include <linux/pinctrl/pinconf.h> | 
 | #include <linux/pinctrl/pinctrl.h> | 
 |  | 
 | #include "../pinctrl-utils.h" | 
 |  | 
 | #define IPROC_GPIO_DATA_IN_OFFSET   0x00 | 
 | #define IPROC_GPIO_DATA_OUT_OFFSET  0x04 | 
 | #define IPROC_GPIO_OUT_EN_OFFSET    0x08 | 
 | #define IPROC_GPIO_INT_TYPE_OFFSET  0x0c | 
 | #define IPROC_GPIO_INT_DE_OFFSET    0x10 | 
 | #define IPROC_GPIO_INT_EDGE_OFFSET  0x14 | 
 | #define IPROC_GPIO_INT_MSK_OFFSET   0x18 | 
 | #define IPROC_GPIO_INT_STAT_OFFSET  0x1c | 
 | #define IPROC_GPIO_INT_MSTAT_OFFSET 0x20 | 
 | #define IPROC_GPIO_INT_CLR_OFFSET   0x24 | 
 | #define IPROC_GPIO_PAD_RES_OFFSET   0x34 | 
 | #define IPROC_GPIO_RES_EN_OFFSET    0x38 | 
 |  | 
 | /* drive strength control for ASIU GPIO */ | 
 | #define IPROC_GPIO_ASIU_DRV0_CTRL_OFFSET 0x58 | 
 |  | 
 | /* pinconf for CCM GPIO */ | 
 | #define IPROC_GPIO_PULL_DN_OFFSET   0x10 | 
 | #define IPROC_GPIO_PULL_UP_OFFSET   0x14 | 
 |  | 
 | /* pinconf for CRMU(aon) GPIO and CCM GPIO*/ | 
 | #define IPROC_GPIO_DRV_CTRL_OFFSET  0x00 | 
 |  | 
 | #define GPIO_BANK_SIZE 0x200 | 
 | #define NGPIOS_PER_BANK 32 | 
 | #define GPIO_BANK(pin) ((pin) / NGPIOS_PER_BANK) | 
 |  | 
 | #define IPROC_GPIO_REG(pin, reg) (GPIO_BANK(pin) * GPIO_BANK_SIZE + (reg)) | 
 | #define IPROC_GPIO_SHIFT(pin) ((pin) % NGPIOS_PER_BANK) | 
 |  | 
 | #define GPIO_DRV_STRENGTH_BIT_SHIFT  20 | 
 | #define GPIO_DRV_STRENGTH_BITS       3 | 
 | #define GPIO_DRV_STRENGTH_BIT_MASK   ((1 << GPIO_DRV_STRENGTH_BITS) - 1) | 
 |  | 
 | enum iproc_pinconf_param { | 
 | 	IPROC_PINCONF_DRIVE_STRENGTH = 0, | 
 | 	IPROC_PINCONF_BIAS_DISABLE, | 
 | 	IPROC_PINCONF_BIAS_PULL_UP, | 
 | 	IPROC_PINCONF_BIAS_PULL_DOWN, | 
 | 	IPROC_PINCON_MAX, | 
 | }; | 
 |  | 
 | enum iproc_pinconf_ctrl_type { | 
 | 	IOCTRL_TYPE_AON = 1, | 
 | 	IOCTRL_TYPE_CDRU, | 
 | 	IOCTRL_TYPE_INVALID, | 
 | }; | 
 |  | 
 | /* | 
 |  * Iproc GPIO core | 
 |  * | 
 |  * @dev: pointer to device | 
 |  * @base: I/O register base for Iproc GPIO controller | 
 |  * @io_ctrl: I/O register base for certain type of Iproc GPIO controller that | 
 |  * has the PINCONF support implemented outside of the GPIO block | 
 |  * @lock: lock to protect access to I/O registers | 
 |  * @gc: GPIO chip | 
 |  * @num_banks: number of GPIO banks, each bank supports up to 32 GPIOs | 
 |  * @pinmux_is_supported: flag to indicate this GPIO controller contains pins | 
 |  * that can be individually muxed to GPIO | 
 |  * @pinconf_disable: contains a list of PINCONF parameters that need to be | 
 |  * disabled | 
 |  * @nr_pinconf_disable: total number of PINCONF parameters that need to be | 
 |  * disabled | 
 |  * @pctl: pointer to pinctrl_dev | 
 |  * @pctldesc: pinctrl descriptor | 
 |  */ | 
 | struct iproc_gpio { | 
 | 	struct device *dev; | 
 |  | 
 | 	void __iomem *base; | 
 | 	void __iomem *io_ctrl; | 
 | 	enum iproc_pinconf_ctrl_type io_ctrl_type; | 
 |  | 
 | 	raw_spinlock_t lock; | 
 |  | 
 | 	struct gpio_chip gc; | 
 | 	unsigned num_banks; | 
 |  | 
 | 	bool pinmux_is_supported; | 
 |  | 
 | 	enum pin_config_param *pinconf_disable; | 
 | 	unsigned int nr_pinconf_disable; | 
 |  | 
 | 	struct pinctrl_dev *pctl; | 
 | 	struct pinctrl_desc pctldesc; | 
 | }; | 
 |  | 
 | /* | 
 |  * Mapping from PINCONF pins to GPIO pins is 1-to-1 | 
 |  */ | 
 | static inline unsigned iproc_pin_to_gpio(unsigned pin) | 
 | { | 
 | 	return pin; | 
 | } | 
 |  | 
 | /** | 
 |  *  iproc_set_bit - set or clear one bit (corresponding to the GPIO pin) in a | 
 |  *  Iproc GPIO register | 
 |  * | 
 |  *  @chip: Iproc GPIO device | 
 |  *  @reg: register offset | 
 |  *  @gpio: GPIO pin | 
 |  *  @set: set or clear | 
 |  */ | 
 | static inline void iproc_set_bit(struct iproc_gpio *chip, unsigned int reg, | 
 | 				  unsigned gpio, bool set) | 
 | { | 
 | 	unsigned int offset = IPROC_GPIO_REG(gpio, reg); | 
 | 	unsigned int shift = IPROC_GPIO_SHIFT(gpio); | 
 | 	u32 val; | 
 |  | 
 | 	val = readl(chip->base + offset); | 
 | 	if (set) | 
 | 		val |= BIT(shift); | 
 | 	else | 
 | 		val &= ~BIT(shift); | 
 | 	writel(val, chip->base + offset); | 
 | } | 
 |  | 
 | static inline bool iproc_get_bit(struct iproc_gpio *chip, unsigned int reg, | 
 | 				  unsigned gpio) | 
 | { | 
 | 	unsigned int offset = IPROC_GPIO_REG(gpio, reg); | 
 | 	unsigned int shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 	return !!(readl(chip->base + offset) & BIT(shift)); | 
 | } | 
 |  | 
 | static void iproc_gpio_irq_handler(struct irq_desc *desc) | 
 | { | 
 | 	struct gpio_chip *gc = irq_desc_get_handler_data(desc); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	struct irq_chip *irq_chip = irq_desc_get_chip(desc); | 
 | 	int i, bit; | 
 |  | 
 | 	chained_irq_enter(irq_chip, desc); | 
 |  | 
 | 	/* go through the entire GPIO banks and handle all interrupts */ | 
 | 	for (i = 0; i < chip->num_banks; i++) { | 
 | 		unsigned long val = readl(chip->base + (i * GPIO_BANK_SIZE) + | 
 | 					  IPROC_GPIO_INT_MSTAT_OFFSET); | 
 |  | 
 | 		for_each_set_bit(bit, &val, NGPIOS_PER_BANK) { | 
 | 			unsigned pin = NGPIOS_PER_BANK * i + bit; | 
 |  | 
 | 			/* | 
 | 			 * Clear the interrupt before invoking the | 
 | 			 * handler, so we do not leave any window | 
 | 			 */ | 
 | 			writel(BIT(bit), chip->base + (i * GPIO_BANK_SIZE) + | 
 | 			       IPROC_GPIO_INT_CLR_OFFSET); | 
 |  | 
 | 			generic_handle_domain_irq(gc->irq.domain, pin); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	chained_irq_exit(irq_chip, desc); | 
 | } | 
 |  | 
 |  | 
 | static void iproc_gpio_irq_ack(struct irq_data *d) | 
 | { | 
 | 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned gpio = d->hwirq; | 
 | 	unsigned int offset = IPROC_GPIO_REG(gpio, | 
 | 			IPROC_GPIO_INT_CLR_OFFSET); | 
 | 	unsigned int shift = IPROC_GPIO_SHIFT(gpio); | 
 | 	u32 val = BIT(shift); | 
 |  | 
 | 	writel(val, chip->base + offset); | 
 | } | 
 |  | 
 | /** | 
 |  *  iproc_gpio_irq_set_mask - mask/unmask a GPIO interrupt | 
 |  * | 
 |  *  @d: IRQ chip data | 
 |  *  @unmask: mask/unmask GPIO interrupt | 
 |  */ | 
 | static void iproc_gpio_irq_set_mask(struct irq_data *d, bool unmask) | 
 | { | 
 | 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned gpio = irqd_to_hwirq(d); | 
 |  | 
 | 	iproc_set_bit(chip, IPROC_GPIO_INT_MSK_OFFSET, gpio, unmask); | 
 | } | 
 |  | 
 | static void iproc_gpio_irq_mask(struct irq_data *d) | 
 | { | 
 | 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned long flags; | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	iproc_gpio_irq_set_mask(d, false); | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 | 	gpiochip_disable_irq(gc, irqd_to_hwirq(d)); | 
 | } | 
 |  | 
 | static void iproc_gpio_irq_unmask(struct irq_data *d) | 
 | { | 
 | 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned long flags; | 
 |  | 
 | 	gpiochip_enable_irq(gc, irqd_to_hwirq(d)); | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	iproc_gpio_irq_set_mask(d, true); | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 | } | 
 |  | 
 | static int iproc_gpio_irq_set_type(struct irq_data *d, unsigned int type) | 
 | { | 
 | 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned gpio = d->hwirq; | 
 | 	bool level_triggered = false; | 
 | 	bool dual_edge = false; | 
 | 	bool rising_or_high = false; | 
 | 	unsigned long flags; | 
 |  | 
 | 	switch (type & IRQ_TYPE_SENSE_MASK) { | 
 | 	case IRQ_TYPE_EDGE_RISING: | 
 | 		rising_or_high = true; | 
 | 		break; | 
 |  | 
 | 	case IRQ_TYPE_EDGE_FALLING: | 
 | 		break; | 
 |  | 
 | 	case IRQ_TYPE_EDGE_BOTH: | 
 | 		dual_edge = true; | 
 | 		break; | 
 |  | 
 | 	case IRQ_TYPE_LEVEL_HIGH: | 
 | 		level_triggered = true; | 
 | 		rising_or_high = true; | 
 | 		break; | 
 |  | 
 | 	case IRQ_TYPE_LEVEL_LOW: | 
 | 		level_triggered = true; | 
 | 		break; | 
 |  | 
 | 	default: | 
 | 		dev_err(chip->dev, "invalid GPIO IRQ type 0x%x\n", | 
 | 			type); | 
 | 		return -EINVAL; | 
 | 	} | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_INT_TYPE_OFFSET, gpio, | 
 | 		       level_triggered); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_INT_DE_OFFSET, gpio, dual_edge); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_INT_EDGE_OFFSET, gpio, | 
 | 		       rising_or_high); | 
 |  | 
 | 	if (type & IRQ_TYPE_EDGE_BOTH) | 
 | 		irq_set_handler_locked(d, handle_edge_irq); | 
 | 	else | 
 | 		irq_set_handler_locked(d, handle_level_irq); | 
 |  | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 |  | 
 | 	dev_dbg(chip->dev, | 
 | 		"gpio:%u level_triggered:%d dual_edge:%d rising_or_high:%d\n", | 
 | 		gpio, level_triggered, dual_edge, rising_or_high); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void iproc_gpio_irq_print_chip(struct irq_data *d, struct seq_file *p) | 
 | { | 
 | 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d); | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 |  | 
 | 	seq_printf(p, dev_name(chip->dev)); | 
 | } | 
 |  | 
 | static const struct irq_chip iproc_gpio_irq_chip = { | 
 | 	.irq_ack = iproc_gpio_irq_ack, | 
 | 	.irq_mask = iproc_gpio_irq_mask, | 
 | 	.irq_unmask = iproc_gpio_irq_unmask, | 
 | 	.irq_set_type = iproc_gpio_irq_set_type, | 
 | 	.irq_enable = iproc_gpio_irq_unmask, | 
 | 	.irq_disable = iproc_gpio_irq_mask, | 
 | 	.irq_print_chip = iproc_gpio_irq_print_chip, | 
 | 	.flags = IRQCHIP_IMMUTABLE, | 
 | 	GPIOCHIP_IRQ_RESOURCE_HELPERS, | 
 | }; | 
 |  | 
 | /* | 
 |  * Request the Iproc IOMUX pinmux controller to mux individual pins to GPIO | 
 |  */ | 
 | static int iproc_gpio_request(struct gpio_chip *gc, unsigned offset) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned gpio = gc->base + offset; | 
 |  | 
 | 	/* not all Iproc GPIO pins can be muxed individually */ | 
 | 	if (!chip->pinmux_is_supported) | 
 | 		return 0; | 
 |  | 
 | 	return pinctrl_gpio_request(gpio); | 
 | } | 
 |  | 
 | static void iproc_gpio_free(struct gpio_chip *gc, unsigned offset) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned gpio = gc->base + offset; | 
 |  | 
 | 	if (!chip->pinmux_is_supported) | 
 | 		return; | 
 |  | 
 | 	pinctrl_gpio_free(gpio); | 
 | } | 
 |  | 
 | static int iproc_gpio_direction_input(struct gpio_chip *gc, unsigned gpio) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned long flags; | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_OUT_EN_OFFSET, gpio, false); | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 |  | 
 | 	dev_dbg(chip->dev, "gpio:%u set input\n", gpio); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int iproc_gpio_direction_output(struct gpio_chip *gc, unsigned gpio, | 
 | 					int val) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned long flags; | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_OUT_EN_OFFSET, gpio, true); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_DATA_OUT_OFFSET, gpio, !!(val)); | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 |  | 
 | 	dev_dbg(chip->dev, "gpio:%u set output, value:%d\n", gpio, val); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int iproc_gpio_get_direction(struct gpio_chip *gc, unsigned int gpio) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned int offset = IPROC_GPIO_REG(gpio, IPROC_GPIO_OUT_EN_OFFSET); | 
 | 	unsigned int shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 	if (readl(chip->base + offset) & BIT(shift)) | 
 | 		return GPIO_LINE_DIRECTION_OUT; | 
 |  | 
 | 	return GPIO_LINE_DIRECTION_IN; | 
 | } | 
 |  | 
 | static void iproc_gpio_set(struct gpio_chip *gc, unsigned gpio, int val) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned long flags; | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	iproc_set_bit(chip, IPROC_GPIO_DATA_OUT_OFFSET, gpio, !!(val)); | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 |  | 
 | 	dev_dbg(chip->dev, "gpio:%u set, value:%d\n", gpio, val); | 
 | } | 
 |  | 
 | static int iproc_gpio_get(struct gpio_chip *gc, unsigned gpio) | 
 | { | 
 | 	struct iproc_gpio *chip = gpiochip_get_data(gc); | 
 | 	unsigned int offset = IPROC_GPIO_REG(gpio, | 
 | 					      IPROC_GPIO_DATA_IN_OFFSET); | 
 | 	unsigned int shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 	return !!(readl(chip->base + offset) & BIT(shift)); | 
 | } | 
 |  | 
 | /* | 
 |  * Mapping of the iProc PINCONF parameters to the generic pin configuration | 
 |  * parameters | 
 |  */ | 
 | static const enum pin_config_param iproc_pinconf_disable_map[] = { | 
 | 	[IPROC_PINCONF_DRIVE_STRENGTH] = PIN_CONFIG_DRIVE_STRENGTH, | 
 | 	[IPROC_PINCONF_BIAS_DISABLE] = PIN_CONFIG_BIAS_DISABLE, | 
 | 	[IPROC_PINCONF_BIAS_PULL_UP] = PIN_CONFIG_BIAS_PULL_UP, | 
 | 	[IPROC_PINCONF_BIAS_PULL_DOWN] = PIN_CONFIG_BIAS_PULL_DOWN, | 
 | }; | 
 |  | 
 | static bool iproc_pinconf_param_is_disabled(struct iproc_gpio *chip, | 
 | 					    enum pin_config_param param) | 
 | { | 
 | 	unsigned int i; | 
 |  | 
 | 	if (!chip->nr_pinconf_disable) | 
 | 		return false; | 
 |  | 
 | 	for (i = 0; i < chip->nr_pinconf_disable; i++) | 
 | 		if (chip->pinconf_disable[i] == param) | 
 | 			return true; | 
 |  | 
 | 	return false; | 
 | } | 
 |  | 
 | static int iproc_pinconf_disable_map_create(struct iproc_gpio *chip, | 
 | 					    unsigned long disable_mask) | 
 | { | 
 | 	unsigned int map_size = ARRAY_SIZE(iproc_pinconf_disable_map); | 
 | 	unsigned int bit, nbits = 0; | 
 |  | 
 | 	/* figure out total number of PINCONF parameters to disable */ | 
 | 	for_each_set_bit(bit, &disable_mask, map_size) | 
 | 		nbits++; | 
 |  | 
 | 	if (!nbits) | 
 | 		return 0; | 
 |  | 
 | 	/* | 
 | 	 * Allocate an array to store PINCONF parameters that need to be | 
 | 	 * disabled | 
 | 	 */ | 
 | 	chip->pinconf_disable = devm_kcalloc(chip->dev, nbits, | 
 | 					     sizeof(*chip->pinconf_disable), | 
 | 					     GFP_KERNEL); | 
 | 	if (!chip->pinconf_disable) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	chip->nr_pinconf_disable = nbits; | 
 |  | 
 | 	/* now store these parameters */ | 
 | 	nbits = 0; | 
 | 	for_each_set_bit(bit, &disable_mask, map_size) | 
 | 		chip->pinconf_disable[nbits++] = iproc_pinconf_disable_map[bit]; | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int iproc_get_groups_count(struct pinctrl_dev *pctldev) | 
 | { | 
 | 	return 1; | 
 | } | 
 |  | 
 | /* | 
 |  * Only one group: "gpio_grp", since this local pinctrl device only performs | 
 |  * GPIO specific PINCONF configurations | 
 |  */ | 
 | static const char *iproc_get_group_name(struct pinctrl_dev *pctldev, | 
 | 					 unsigned selector) | 
 | { | 
 | 	return "gpio_grp"; | 
 | } | 
 |  | 
 | static const struct pinctrl_ops iproc_pctrl_ops = { | 
 | 	.get_groups_count = iproc_get_groups_count, | 
 | 	.get_group_name = iproc_get_group_name, | 
 | 	.dt_node_to_map = pinconf_generic_dt_node_to_map_pin, | 
 | 	.dt_free_map = pinctrl_utils_free_map, | 
 | }; | 
 |  | 
 | static int iproc_gpio_set_pull(struct iproc_gpio *chip, unsigned gpio, | 
 | 				bool disable, bool pull_up) | 
 | { | 
 | 	void __iomem *base; | 
 | 	unsigned long flags; | 
 | 	unsigned int shift; | 
 | 	u32 val_1, val_2; | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	if (chip->io_ctrl_type == IOCTRL_TYPE_CDRU) { | 
 | 		base = chip->io_ctrl; | 
 | 		shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 		val_1 = readl(base + IPROC_GPIO_PULL_UP_OFFSET); | 
 | 		val_2 = readl(base + IPROC_GPIO_PULL_DN_OFFSET); | 
 | 		if (disable) { | 
 | 			/* no pull-up or pull-down */ | 
 | 			val_1 &= ~BIT(shift); | 
 | 			val_2 &= ~BIT(shift); | 
 | 		} else if (pull_up) { | 
 | 			val_1 |= BIT(shift); | 
 | 			val_2 &= ~BIT(shift); | 
 | 		} else { | 
 | 			val_1 &= ~BIT(shift); | 
 | 			val_2 |= BIT(shift); | 
 | 		} | 
 | 		writel(val_1, base + IPROC_GPIO_PULL_UP_OFFSET); | 
 | 		writel(val_2, base + IPROC_GPIO_PULL_DN_OFFSET); | 
 | 	} else { | 
 | 		if (disable) { | 
 | 			iproc_set_bit(chip, IPROC_GPIO_RES_EN_OFFSET, gpio, | 
 | 				      false); | 
 | 		} else { | 
 | 			iproc_set_bit(chip, IPROC_GPIO_PAD_RES_OFFSET, gpio, | 
 | 				      pull_up); | 
 | 			iproc_set_bit(chip, IPROC_GPIO_RES_EN_OFFSET, gpio, | 
 | 				      true); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 | 	dev_dbg(chip->dev, "gpio:%u set pullup:%d\n", gpio, pull_up); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void iproc_gpio_get_pull(struct iproc_gpio *chip, unsigned gpio, | 
 | 				 bool *disable, bool *pull_up) | 
 | { | 
 | 	void __iomem *base; | 
 | 	unsigned long flags; | 
 | 	unsigned int shift; | 
 | 	u32 val_1, val_2; | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	if (chip->io_ctrl_type == IOCTRL_TYPE_CDRU) { | 
 | 		base = chip->io_ctrl; | 
 | 		shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 		val_1 = readl(base + IPROC_GPIO_PULL_UP_OFFSET) & BIT(shift); | 
 | 		val_2 = readl(base + IPROC_GPIO_PULL_DN_OFFSET) & BIT(shift); | 
 |  | 
 | 		*pull_up = val_1 ? true : false; | 
 | 		*disable = (val_1 | val_2) ? false : true; | 
 |  | 
 | 	} else { | 
 | 		*disable = !iproc_get_bit(chip, IPROC_GPIO_RES_EN_OFFSET, gpio); | 
 | 		*pull_up = iproc_get_bit(chip, IPROC_GPIO_PAD_RES_OFFSET, gpio); | 
 | 	} | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 | } | 
 |  | 
 | #define DRV_STRENGTH_OFFSET(gpio, bit, type)  ((type) == IOCTRL_TYPE_AON ? \ | 
 | 	((2 - (bit)) * 4 + IPROC_GPIO_DRV_CTRL_OFFSET) : \ | 
 | 	((type) == IOCTRL_TYPE_CDRU) ? \ | 
 | 	((bit) * 4 + IPROC_GPIO_DRV_CTRL_OFFSET) : \ | 
 | 	((bit) * 4 + IPROC_GPIO_REG(gpio, IPROC_GPIO_ASIU_DRV0_CTRL_OFFSET))) | 
 |  | 
 | static int iproc_gpio_set_strength(struct iproc_gpio *chip, unsigned gpio, | 
 | 				    unsigned strength) | 
 | { | 
 | 	void __iomem *base; | 
 | 	unsigned int i, offset, shift; | 
 | 	u32 val; | 
 | 	unsigned long flags; | 
 |  | 
 | 	/* make sure drive strength is supported */ | 
 | 	if (strength < 2 ||  strength > 16 || (strength % 2)) | 
 | 		return -ENOTSUPP; | 
 |  | 
 | 	if (chip->io_ctrl) { | 
 | 		base = chip->io_ctrl; | 
 | 	} else { | 
 | 		base = chip->base; | 
 | 	} | 
 |  | 
 | 	shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 	dev_dbg(chip->dev, "gpio:%u set drive strength:%d mA\n", gpio, | 
 | 		strength); | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	strength = (strength / 2) - 1; | 
 | 	for (i = 0; i < GPIO_DRV_STRENGTH_BITS; i++) { | 
 | 		offset = DRV_STRENGTH_OFFSET(gpio, i, chip->io_ctrl_type); | 
 | 		val = readl(base + offset); | 
 | 		val &= ~BIT(shift); | 
 | 		val |= ((strength >> i) & 0x1) << shift; | 
 | 		writel(val, base + offset); | 
 | 	} | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int iproc_gpio_get_strength(struct iproc_gpio *chip, unsigned gpio, | 
 | 				    u16 *strength) | 
 | { | 
 | 	void __iomem *base; | 
 | 	unsigned int i, offset, shift; | 
 | 	u32 val; | 
 | 	unsigned long flags; | 
 |  | 
 | 	if (chip->io_ctrl) { | 
 | 		base = chip->io_ctrl; | 
 | 	} else { | 
 | 		base = chip->base; | 
 | 	} | 
 |  | 
 | 	shift = IPROC_GPIO_SHIFT(gpio); | 
 |  | 
 | 	raw_spin_lock_irqsave(&chip->lock, flags); | 
 | 	*strength = 0; | 
 | 	for (i = 0; i < GPIO_DRV_STRENGTH_BITS; i++) { | 
 | 		offset = DRV_STRENGTH_OFFSET(gpio, i, chip->io_ctrl_type); | 
 | 		val = readl(base + offset) & BIT(shift); | 
 | 		val >>= shift; | 
 | 		*strength += (val << i); | 
 | 	} | 
 |  | 
 | 	/* convert to mA */ | 
 | 	*strength = (*strength + 1) * 2; | 
 | 	raw_spin_unlock_irqrestore(&chip->lock, flags); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static int iproc_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin, | 
 | 				 unsigned long *config) | 
 | { | 
 | 	struct iproc_gpio *chip = pinctrl_dev_get_drvdata(pctldev); | 
 | 	enum pin_config_param param = pinconf_to_config_param(*config); | 
 | 	unsigned gpio = iproc_pin_to_gpio(pin); | 
 | 	u16 arg; | 
 | 	bool disable, pull_up; | 
 | 	int ret; | 
 |  | 
 | 	if (iproc_pinconf_param_is_disabled(chip, param)) | 
 | 		return -ENOTSUPP; | 
 |  | 
 | 	switch (param) { | 
 | 	case PIN_CONFIG_BIAS_DISABLE: | 
 | 		iproc_gpio_get_pull(chip, gpio, &disable, &pull_up); | 
 | 		if (disable) | 
 | 			return 0; | 
 | 		else | 
 | 			return -EINVAL; | 
 |  | 
 | 	case PIN_CONFIG_BIAS_PULL_UP: | 
 | 		iproc_gpio_get_pull(chip, gpio, &disable, &pull_up); | 
 | 		if (!disable && pull_up) | 
 | 			return 0; | 
 | 		else | 
 | 			return -EINVAL; | 
 |  | 
 | 	case PIN_CONFIG_BIAS_PULL_DOWN: | 
 | 		iproc_gpio_get_pull(chip, gpio, &disable, &pull_up); | 
 | 		if (!disable && !pull_up) | 
 | 			return 0; | 
 | 		else | 
 | 			return -EINVAL; | 
 |  | 
 | 	case PIN_CONFIG_DRIVE_STRENGTH: | 
 | 		ret = iproc_gpio_get_strength(chip, gpio, &arg); | 
 | 		if (ret) | 
 | 			return ret; | 
 | 		*config = pinconf_to_config_packed(param, arg); | 
 |  | 
 | 		return 0; | 
 |  | 
 | 	default: | 
 | 		return -ENOTSUPP; | 
 | 	} | 
 |  | 
 | 	return -ENOTSUPP; | 
 | } | 
 |  | 
 | static int iproc_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin, | 
 | 				 unsigned long *configs, unsigned num_configs) | 
 | { | 
 | 	struct iproc_gpio *chip = pinctrl_dev_get_drvdata(pctldev); | 
 | 	enum pin_config_param param; | 
 | 	u32 arg; | 
 | 	unsigned i, gpio = iproc_pin_to_gpio(pin); | 
 | 	int ret = -ENOTSUPP; | 
 |  | 
 | 	for (i = 0; i < num_configs; i++) { | 
 | 		param = pinconf_to_config_param(configs[i]); | 
 |  | 
 | 		if (iproc_pinconf_param_is_disabled(chip, param)) | 
 | 			return -ENOTSUPP; | 
 |  | 
 | 		arg = pinconf_to_config_argument(configs[i]); | 
 |  | 
 | 		switch (param) { | 
 | 		case PIN_CONFIG_BIAS_DISABLE: | 
 | 			ret = iproc_gpio_set_pull(chip, gpio, true, false); | 
 | 			if (ret < 0) | 
 | 				goto out; | 
 | 			break; | 
 |  | 
 | 		case PIN_CONFIG_BIAS_PULL_UP: | 
 | 			ret = iproc_gpio_set_pull(chip, gpio, false, true); | 
 | 			if (ret < 0) | 
 | 				goto out; | 
 | 			break; | 
 |  | 
 | 		case PIN_CONFIG_BIAS_PULL_DOWN: | 
 | 			ret = iproc_gpio_set_pull(chip, gpio, false, false); | 
 | 			if (ret < 0) | 
 | 				goto out; | 
 | 			break; | 
 |  | 
 | 		case PIN_CONFIG_DRIVE_STRENGTH: | 
 | 			ret = iproc_gpio_set_strength(chip, gpio, arg); | 
 | 			if (ret < 0) | 
 | 				goto out; | 
 | 			break; | 
 |  | 
 | 		default: | 
 | 			dev_err(chip->dev, "invalid configuration\n"); | 
 | 			return -ENOTSUPP; | 
 | 		} | 
 | 	} /* for each config */ | 
 |  | 
 | out: | 
 | 	return ret; | 
 | } | 
 |  | 
 | static const struct pinconf_ops iproc_pconf_ops = { | 
 | 	.is_generic = true, | 
 | 	.pin_config_get = iproc_pin_config_get, | 
 | 	.pin_config_set = iproc_pin_config_set, | 
 | }; | 
 |  | 
 | /* | 
 |  * Iproc GPIO controller supports some PINCONF related configurations such as | 
 |  * pull up, pull down, and drive strength, when the pin is configured to GPIO | 
 |  * | 
 |  * Here a local pinctrl device is created with simple 1-to-1 pin mapping to the | 
 |  * local GPIO pins | 
 |  */ | 
 | static int iproc_gpio_register_pinconf(struct iproc_gpio *chip) | 
 | { | 
 | 	struct pinctrl_desc *pctldesc = &chip->pctldesc; | 
 | 	struct pinctrl_pin_desc *pins; | 
 | 	struct gpio_chip *gc = &chip->gc; | 
 | 	int i; | 
 |  | 
 | 	pins = devm_kcalloc(chip->dev, gc->ngpio, sizeof(*pins), GFP_KERNEL); | 
 | 	if (!pins) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	for (i = 0; i < gc->ngpio; i++) { | 
 | 		pins[i].number = i; | 
 | 		pins[i].name = devm_kasprintf(chip->dev, GFP_KERNEL, | 
 | 					      "gpio-%d", i); | 
 | 		if (!pins[i].name) | 
 | 			return -ENOMEM; | 
 | 	} | 
 |  | 
 | 	pctldesc->name = dev_name(chip->dev); | 
 | 	pctldesc->pctlops = &iproc_pctrl_ops; | 
 | 	pctldesc->pins = pins; | 
 | 	pctldesc->npins = gc->ngpio; | 
 | 	pctldesc->confops = &iproc_pconf_ops; | 
 |  | 
 | 	chip->pctl = devm_pinctrl_register(chip->dev, pctldesc, chip); | 
 | 	if (IS_ERR(chip->pctl)) { | 
 | 		dev_err(chip->dev, "unable to register pinctrl device\n"); | 
 | 		return PTR_ERR(chip->pctl); | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static const struct of_device_id iproc_gpio_of_match[] = { | 
 | 	{ .compatible = "brcm,iproc-gpio" }, | 
 | 	{ .compatible = "brcm,cygnus-ccm-gpio" }, | 
 | 	{ .compatible = "brcm,cygnus-asiu-gpio" }, | 
 | 	{ .compatible = "brcm,cygnus-crmu-gpio" }, | 
 | 	{ .compatible = "brcm,iproc-nsp-gpio" }, | 
 | 	{ .compatible = "brcm,iproc-stingray-gpio" }, | 
 | 	{ /* sentinel */ } | 
 | }; | 
 |  | 
 | static int iproc_gpio_probe(struct platform_device *pdev) | 
 | { | 
 | 	struct device *dev = &pdev->dev; | 
 | 	struct resource *res; | 
 | 	struct iproc_gpio *chip; | 
 | 	struct gpio_chip *gc; | 
 | 	u32 ngpios, pinconf_disable_mask = 0; | 
 | 	int irq, ret; | 
 | 	bool no_pinconf = false; | 
 | 	enum iproc_pinconf_ctrl_type io_ctrl_type = IOCTRL_TYPE_INVALID; | 
 |  | 
 | 	/* NSP does not support drive strength config */ | 
 | 	if (of_device_is_compatible(dev->of_node, "brcm,iproc-nsp-gpio")) | 
 | 		pinconf_disable_mask = BIT(IPROC_PINCONF_DRIVE_STRENGTH); | 
 | 	/* Stingray does not support pinconf in this controller */ | 
 | 	else if (of_device_is_compatible(dev->of_node, | 
 | 					 "brcm,iproc-stingray-gpio")) | 
 | 		no_pinconf = true; | 
 |  | 
 | 	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL); | 
 | 	if (!chip) | 
 | 		return -ENOMEM; | 
 |  | 
 | 	chip->dev = dev; | 
 | 	platform_set_drvdata(pdev, chip); | 
 |  | 
 | 	chip->base = devm_platform_ioremap_resource(pdev, 0); | 
 | 	if (IS_ERR(chip->base)) { | 
 | 		dev_err(dev, "unable to map I/O memory\n"); | 
 | 		return PTR_ERR(chip->base); | 
 | 	} | 
 |  | 
 | 	res = platform_get_resource(pdev, IORESOURCE_MEM, 1); | 
 | 	if (res) { | 
 | 		chip->io_ctrl = devm_ioremap_resource(dev, res); | 
 | 		if (IS_ERR(chip->io_ctrl)) | 
 | 			return PTR_ERR(chip->io_ctrl); | 
 | 		if (of_device_is_compatible(dev->of_node, | 
 | 					    "brcm,cygnus-ccm-gpio")) | 
 | 			io_ctrl_type = IOCTRL_TYPE_CDRU; | 
 | 		else | 
 | 			io_ctrl_type = IOCTRL_TYPE_AON; | 
 | 	} | 
 |  | 
 | 	chip->io_ctrl_type = io_ctrl_type; | 
 |  | 
 | 	if (of_property_read_u32(dev->of_node, "ngpios", &ngpios)) { | 
 | 		dev_err(&pdev->dev, "missing ngpios DT property\n"); | 
 | 		return -ENODEV; | 
 | 	} | 
 |  | 
 | 	raw_spin_lock_init(&chip->lock); | 
 |  | 
 | 	gc = &chip->gc; | 
 | 	gc->base = -1; | 
 | 	gc->ngpio = ngpios; | 
 | 	chip->num_banks = (ngpios + NGPIOS_PER_BANK - 1) / NGPIOS_PER_BANK; | 
 | 	gc->label = dev_name(dev); | 
 | 	gc->parent = dev; | 
 | 	gc->request = iproc_gpio_request; | 
 | 	gc->free = iproc_gpio_free; | 
 | 	gc->direction_input = iproc_gpio_direction_input; | 
 | 	gc->direction_output = iproc_gpio_direction_output; | 
 | 	gc->get_direction = iproc_gpio_get_direction; | 
 | 	gc->set = iproc_gpio_set; | 
 | 	gc->get = iproc_gpio_get; | 
 |  | 
 | 	chip->pinmux_is_supported = of_property_read_bool(dev->of_node, | 
 | 							"gpio-ranges"); | 
 |  | 
 | 	/* optional GPIO interrupt support */ | 
 | 	irq = platform_get_irq_optional(pdev, 0); | 
 | 	if (irq > 0) { | 
 | 		struct gpio_irq_chip *girq; | 
 |  | 
 | 		girq = &gc->irq; | 
 | 		gpio_irq_chip_set_chip(girq, &iproc_gpio_irq_chip); | 
 | 		girq->parent_handler = iproc_gpio_irq_handler; | 
 | 		girq->num_parents = 1; | 
 | 		girq->parents = devm_kcalloc(dev, 1, | 
 | 					     sizeof(*girq->parents), | 
 | 					     GFP_KERNEL); | 
 | 		if (!girq->parents) | 
 | 			return -ENOMEM; | 
 | 		girq->parents[0] = irq; | 
 | 		girq->default_type = IRQ_TYPE_NONE; | 
 | 		girq->handler = handle_bad_irq; | 
 | 	} | 
 |  | 
 | 	ret = gpiochip_add_data(gc, chip); | 
 | 	if (ret < 0) { | 
 | 		dev_err(dev, "unable to add GPIO chip\n"); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	if (!no_pinconf) { | 
 | 		ret = iproc_gpio_register_pinconf(chip); | 
 | 		if (ret) { | 
 | 			dev_err(dev, "unable to register pinconf\n"); | 
 | 			goto err_rm_gpiochip; | 
 | 		} | 
 |  | 
 | 		if (pinconf_disable_mask) { | 
 | 			ret = iproc_pinconf_disable_map_create(chip, | 
 | 							 pinconf_disable_mask); | 
 | 			if (ret) { | 
 | 				dev_err(dev, | 
 | 					"unable to create pinconf disable map\n"); | 
 | 				goto err_rm_gpiochip; | 
 | 			} | 
 | 		} | 
 | 	} | 
 |  | 
 | 	return 0; | 
 |  | 
 | err_rm_gpiochip: | 
 | 	gpiochip_remove(gc); | 
 |  | 
 | 	return ret; | 
 | } | 
 |  | 
 | static struct platform_driver iproc_gpio_driver = { | 
 | 	.driver = { | 
 | 		.name = "iproc-gpio", | 
 | 		.of_match_table = iproc_gpio_of_match, | 
 | 	}, | 
 | 	.probe = iproc_gpio_probe, | 
 | }; | 
 |  | 
 | static int __init iproc_gpio_init(void) | 
 | { | 
 | 	return platform_driver_register(&iproc_gpio_driver); | 
 | } | 
 | arch_initcall_sync(iproc_gpio_init); |