| |
| /* |
| * Copyright (C) 2013 STMicroelectronics Limited. |
| * Author: Srinivas Kandagatla <srinivas.kandagatla@st.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * publishhed by the Free Software Foundation. |
| */ |
| #include "st-pincfg.h" |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| / { |
| |
| aliases { |
| gpio0 = &PIO0; |
| gpio1 = &PIO1; |
| gpio2 = &PIO2; |
| gpio3 = &PIO3; |
| gpio4 = &PIO4; |
| gpio5 = &PIO40; |
| gpio6 = &PIO5; |
| gpio7 = &PIO6; |
| gpio8 = &PIO7; |
| gpio9 = &PIO8; |
| gpio10 = &PIO9; |
| gpio11 = &PIO10; |
| gpio12 = &PIO11; |
| gpio13 = &PIO12; |
| gpio14 = &PIO30; |
| gpio15 = &PIO31; |
| gpio16 = &PIO13; |
| gpio17 = &PIO14; |
| gpio18 = &PIO15; |
| gpio19 = &PIO16; |
| gpio20 = &PIO17; |
| gpio21 = &PIO18; |
| gpio22 = &PIO100; |
| gpio23 = &PIO101; |
| gpio24 = &PIO102; |
| gpio25 = &PIO103; |
| gpio26 = &PIO104; |
| gpio27 = &PIO105; |
| gpio28 = &PIO106; |
| gpio29 = &PIO107; |
| }; |
| |
| soc { |
| pin-controller-sbc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stih416-sbc-pinctrl"; |
| st,syscfg = <&syscfg_sbc>; |
| reg = <0xfe61f080 0x4>; |
| reg-names = "irqmux"; |
| interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "irqmux"; |
| ranges = <0 0xfe610000 0x6000>; |
| |
| PIO0: gpio@fe610000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0 0x100>; |
| st,bank-name = "PIO0"; |
| }; |
| PIO1: gpio@fe611000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x1000 0x100>; |
| st,bank-name = "PIO1"; |
| }; |
| PIO2: gpio@fe612000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x2000 0x100>; |
| st,bank-name = "PIO2"; |
| }; |
| PIO3: gpio@fe613000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x3000 0x100>; |
| st,bank-name = "PIO3"; |
| }; |
| PIO4: gpio@fe614000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x4000 0x100>; |
| st,bank-name = "PIO4"; |
| }; |
| PIO40: gpio@fe615000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x5000 0x100>; |
| st,bank-name = "PIO40"; |
| st,retime-pin-mask = <0x7f>; |
| }; |
| |
| rc{ |
| pinctrl_ir: ir0 { |
| st,pins { |
| ir = <&PIO4 0 ALT2 IN>; |
| }; |
| }; |
| }; |
| sbc_serial1 { |
| pinctrl_sbc_serial1: sbc_serial1 { |
| st,pins { |
| tx = <&PIO2 6 ALT3 OUT>; |
| rx = <&PIO2 7 ALT3 IN>; |
| }; |
| }; |
| }; |
| |
| keyscan { |
| pinctrl_keyscan: keyscan { |
| st,pins { |
| keyin0 = <&PIO0 2 ALT2 IN>; |
| keyin1 = <&PIO0 3 ALT2 IN>; |
| keyin2 = <&PIO0 4 ALT2 IN>; |
| keyin3 = <&PIO2 6 ALT2 IN>; |
| |
| keyout0 = <&PIO1 6 ALT2 OUT>; |
| keyout1 = <&PIO1 7 ALT2 OUT>; |
| keyout2 = <&PIO0 6 ALT2 OUT>; |
| keyout3 = <&PIO2 7 ALT2 OUT>; |
| }; |
| }; |
| }; |
| |
| sbc_i2c0 { |
| pinctrl_sbc_i2c0_default: sbc_i2c0-default { |
| st,pins { |
| sda = <&PIO4 6 ALT1 BIDIR>; |
| scl = <&PIO4 5 ALT1 BIDIR>; |
| }; |
| }; |
| }; |
| |
| sbc_i2c1 { |
| pinctrl_sbc_i2c1_default: sbc_i2c1-default { |
| st,pins { |
| sda = <&PIO3 2 ALT2 BIDIR>; |
| scl = <&PIO3 1 ALT2 BIDIR>; |
| }; |
| }; |
| }; |
| |
| gmac1 { |
| pinctrl_mii1: mii1 { |
| st,pins { |
| txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>; |
| txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>; |
| txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>; |
| txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>; |
| txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>; |
| txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>; |
| txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; |
| col = <&PIO0 7 ALT1 IN BYPASS 1000>; |
| |
| mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>; |
| mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; |
| crs = <&PIO1 2 ALT1 IN BYPASS 1000>; |
| mdint = <&PIO1 3 ALT1 IN BYPASS 0>; |
| rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>; |
| rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>; |
| rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>; |
| rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>; |
| |
| rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>; |
| rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>; |
| rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; |
| phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>; |
| }; |
| }; |
| pinctrl_rgmii1: rgmii1-0 { |
| st,pins { |
| txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>; |
| txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>; |
| txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>; |
| txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>; |
| txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>; |
| txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; |
| |
| mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; |
| mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; |
| rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>; |
| rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>; |
| rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>; |
| rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>; |
| |
| rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>; |
| rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; |
| phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>; |
| |
| clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>; |
| }; |
| }; |
| }; |
| }; |
| |
| pin-controller-front { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stih416-front-pinctrl"; |
| st,syscfg = <&syscfg_front>; |
| reg = <0xfee0f080 0x4>; |
| reg-names = "irqmux"; |
| interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "irqmux"; |
| ranges = <0 0xfee00000 0x10000>; |
| |
| PIO5: gpio@fee00000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0 0x100>; |
| st,bank-name = "PIO5"; |
| }; |
| PIO6: gpio@fee01000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x1000 0x100>; |
| st,bank-name = "PIO6"; |
| }; |
| PIO7: gpio@fee02000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x2000 0x100>; |
| st,bank-name = "PIO7"; |
| }; |
| PIO8: gpio@fee03000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x3000 0x100>; |
| st,bank-name = "PIO8"; |
| }; |
| PIO9: gpio@fee04000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x4000 0x100>; |
| st,bank-name = "PIO9"; |
| }; |
| PIO10: gpio@fee05000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x5000 0x100>; |
| st,bank-name = "PIO10"; |
| }; |
| PIO11: gpio@fee06000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x6000 0x100>; |
| st,bank-name = "PIO11"; |
| }; |
| PIO12: gpio@fee07000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x7000 0x100>; |
| st,bank-name = "PIO12"; |
| }; |
| PIO30: gpio@fee08000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x8000 0x100>; |
| st,bank-name = "PIO30"; |
| }; |
| PIO31: gpio@fee09000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x9000 0x100>; |
| st,bank-name = "PIO31"; |
| }; |
| |
| serial2-oe { |
| pinctrl_serial2_oe: serial2-1 { |
| st,pins { |
| output-enable = <&PIO11 3 ALT2 OUT>; |
| }; |
| }; |
| }; |
| |
| i2c0 { |
| pinctrl_i2c0_default: i2c0-default { |
| st,pins { |
| sda = <&PIO9 3 ALT1 BIDIR>; |
| scl = <&PIO9 2 ALT1 BIDIR>; |
| }; |
| }; |
| }; |
| |
| i2c1 { |
| pinctrl_i2c1_default: i2c1-default { |
| st,pins { |
| sda = <&PIO12 1 ALT1 BIDIR>; |
| scl = <&PIO12 0 ALT1 BIDIR>; |
| }; |
| }; |
| }; |
| |
| fsm { |
| pinctrl_fsm: fsm { |
| st,pins { |
| spi-fsm-clk = <&PIO12 2 ALT1 OUT>; |
| spi-fsm-cs = <&PIO12 3 ALT1 OUT>; |
| spi-fsm-mosi = <&PIO12 4 ALT1 OUT>; |
| spi-fsm-miso = <&PIO12 5 ALT1 IN>; |
| spi-fsm-hol = <&PIO12 6 ALT1 OUT>; |
| spi-fsm-wp = <&PIO12 7 ALT1 OUT>; |
| }; |
| }; |
| }; |
| }; |
| |
| pin-controller-rear { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stih416-rear-pinctrl"; |
| st,syscfg = <&syscfg_rear>; |
| reg = <0xfe82f080 0x4>; |
| reg-names = "irqmux"; |
| interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "irqmux"; |
| ranges = <0 0xfe820000 0x6000>; |
| |
| PIO13: gpio@fe820000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0 0x100>; |
| st,bank-name = "PIO13"; |
| }; |
| PIO14: gpio@fe821000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x1000 0x100>; |
| st,bank-name = "PIO14"; |
| }; |
| PIO15: gpio@fe822000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x2000 0x100>; |
| st,bank-name = "PIO15"; |
| }; |
| PIO16: gpio@fe823000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x3000 0x100>; |
| st,bank-name = "PIO16"; |
| }; |
| PIO17: gpio@fe824000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x4000 0x100>; |
| st,bank-name = "PIO17"; |
| }; |
| PIO18: gpio@fe825000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x5000 0x100>; |
| st,bank-name = "PIO18"; |
| st,retime-pin-mask = <0xf>; |
| }; |
| |
| serial2 { |
| pinctrl_serial2: serial2-0 { |
| st,pins { |
| tx = <&PIO17 4 ALT2 OUT>; |
| rx = <&PIO17 5 ALT2 IN>; |
| }; |
| }; |
| }; |
| |
| gmac0 { |
| pinctrl_mii0: mii0 { |
| st,pins { |
| mdint = <&PIO13 6 ALT2 IN BYPASS 0>; |
| txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>; |
| txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>; |
| txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; |
| txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>; |
| txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>; |
| |
| txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; |
| txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; |
| crs = <&PIO15 2 ALT2 IN BYPASS 1000>; |
| col = <&PIO15 3 ALT2 IN BYPASS 1000>; |
| mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>; |
| mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; |
| |
| rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>; |
| rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>; |
| rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>; |
| rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>; |
| rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>; |
| rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>; |
| rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; |
| phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>; |
| }; |
| }; |
| |
| pinctrl_gmii0: gmii0 { |
| st,pins { |
| }; |
| }; |
| pinctrl_rgmii0: rgmii0 { |
| st,pins { |
| phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>; |
| txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>; |
| txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>; |
| txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>; |
| txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>; |
| txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>; |
| txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; |
| |
| mdio = <&PIO15 4 ALT2 OUT BYPASS 0>; |
| mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; |
| |
| rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>; |
| rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>; |
| rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>; |
| rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>; |
| rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>; |
| rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>; |
| |
| clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>; |
| }; |
| }; |
| }; |
| }; |
| |
| pin-controller-fvdp-fe { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stih416-fvdp-fe-pinctrl"; |
| st,syscfg = <&syscfg_fvdp_fe>; |
| reg = <0xfd6bf080 0x4>; |
| reg-names = "irqmux"; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "irqmux"; |
| ranges = <0 0xfd6b0000 0x3000>; |
| |
| PIO100: gpio@fd6b0000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0 0x100>; |
| st,bank-name = "PIO100"; |
| }; |
| PIO101: gpio@fd6b1000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x1000 0x100>; |
| st,bank-name = "PIO101"; |
| }; |
| PIO102: gpio@fd6b2000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x2000 0x100>; |
| st,bank-name = "PIO102"; |
| }; |
| }; |
| |
| pin-controller-fvdp-lite { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "st,stih416-fvdp-lite-pinctrl"; |
| st,syscfg = <&syscfg_fvdp_lite>; |
| reg = <0xfd33f080 0x4>; |
| reg-names = "irqmux"; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "irqmux"; |
| ranges = <0 0xfd330000 0x5000>; |
| |
| PIO103: gpio@fd330000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0 0x100>; |
| st,bank-name = "PIO103"; |
| }; |
| PIO104: gpio@fd331000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x1000 0x100>; |
| st,bank-name = "PIO104"; |
| }; |
| PIO105: gpio@fd332000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x2000 0x100>; |
| st,bank-name = "PIO105"; |
| }; |
| PIO106: gpio@fd333000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x3000 0x100>; |
| st,bank-name = "PIO106"; |
| }; |
| |
| PIO107: gpio@fd334000 { |
| gpio-controller; |
| #gpio-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x4000 0x100>; |
| st,bank-name = "PIO107"; |
| st,retime-pin-mask = <0xf>; |
| }; |
| }; |
| }; |
| }; |
