|  | Kernel driver ads1015 | 
|  | ===================== | 
|  |  | 
|  | Supported chips: | 
|  | * Texas Instruments ADS1015 | 
|  | Prefix: 'ads1015' | 
|  | Datasheet: Publicly available at the Texas Instruments website : | 
|  | http://focus.ti.com/lit/ds/symlink/ads1015.pdf | 
|  | * Texas Instruments ADS1115 | 
|  | Prefix: 'ads1115' | 
|  | Datasheet: Publicly available at the Texas Instruments website : | 
|  | http://focus.ti.com/lit/ds/symlink/ads1115.pdf | 
|  |  | 
|  | Authors: | 
|  | Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de> | 
|  |  | 
|  | Description | 
|  | ----------- | 
|  |  | 
|  | This driver implements support for the Texas Instruments ADS1015/ADS1115. | 
|  |  | 
|  | This device is a 12/16-bit A-D converter with 4 inputs. | 
|  |  | 
|  | The inputs can be used single ended or in certain differential combinations. | 
|  |  | 
|  | The inputs can be made available by 8 sysfs input files in0_input - in7_input: | 
|  | in0: Voltage over AIN0 and AIN1. | 
|  | in1: Voltage over AIN0 and AIN3. | 
|  | in2: Voltage over AIN1 and AIN3. | 
|  | in3: Voltage over AIN2 and AIN3. | 
|  | in4: Voltage over AIN0 and GND. | 
|  | in5: Voltage over AIN1 and GND. | 
|  | in6: Voltage over AIN2 and GND. | 
|  | in7: Voltage over AIN3 and GND. | 
|  |  | 
|  | Which inputs are available can be configured using platform data or devicetree. | 
|  |  | 
|  | By default all inputs are exported. | 
|  |  | 
|  | Platform Data | 
|  | ------------- | 
|  |  | 
|  | In linux/i2c/ads1015.h platform data is defined, channel_data contains | 
|  | configuration data for the used input combinations: | 
|  | - pga is the programmable gain amplifier (values are full scale) | 
|  | 0: +/- 6.144 V | 
|  | 1: +/- 4.096 V | 
|  | 2: +/- 2.048 V | 
|  | 3: +/- 1.024 V | 
|  | 4: +/- 0.512 V | 
|  | 5: +/- 0.256 V | 
|  | - data_rate in samples per second | 
|  | 0: 128 | 
|  | 1: 250 | 
|  | 2: 490 | 
|  | 3: 920 | 
|  | 4: 1600 | 
|  | 5: 2400 | 
|  | 6: 3300 | 
|  |  | 
|  | Example: | 
|  | struct ads1015_platform_data data = { | 
|  | .channel_data = { | 
|  | [2] = { .enabled = true, .pga = 1, .data_rate = 0 }, | 
|  | [4] = { .enabled = true, .pga = 4, .data_rate = 5 }, | 
|  | } | 
|  | }; | 
|  |  | 
|  | In this case only in2_input (FS +/- 4.096 V, 128 SPS) and in4_input | 
|  | (FS +/- 0.512 V, 2400 SPS) would be created. | 
|  |  | 
|  | Devicetree | 
|  | ---------- | 
|  |  | 
|  | Configuration is also possible via devicetree: | 
|  | Documentation/devicetree/bindings/hwmon/ads1015.txt |