| /* |
| * P1025 RDB Device Tree Source stub (no addresses or top-level ranges) |
| * |
| * Copyright 2011 Freescale Semiconductor Inc. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are met: |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution. |
| * * Neither the name of Freescale Semiconductor nor the |
| * names of its contributors may be used to endorse or promote products |
| * derived from this software without specific prior written permission. |
| * |
| * |
| * ALTERNATIVELY, this software may be distributed under the terms of the |
| * GNU General Public License ("GPL") as published by the Free Software |
| * Foundation, either version 2 of that License or (at your option) any |
| * later version. |
| * |
| * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY |
| * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED |
| * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
| * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY |
| * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES |
| * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; |
| * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND |
| * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS |
| * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| &lbc { |
| nor@0,0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "cfi-flash"; |
| reg = <0x0 0x0 0x1000000>; |
| bank-width = <2>; |
| device-width = <1>; |
| |
| partition@0 { |
| /* This location must not be altered */ |
| /* 256KB for Vitesse 7385 Switch firmware */ |
| reg = <0x0 0x00040000>; |
| label = "NOR Vitesse-7385 Firmware"; |
| read-only; |
| }; |
| |
| partition@40000 { |
| /* 256KB for DTB Image */ |
| reg = <0x00040000 0x00040000>; |
| label = "NOR DTB Image"; |
| }; |
| |
| partition@80000 { |
| /* 3.5 MB for Linux Kernel Image */ |
| reg = <0x00080000 0x00380000>; |
| label = "NOR Linux Kernel Image"; |
| }; |
| |
| partition@400000 { |
| /* 11MB for JFFS2 based Root file System */ |
| reg = <0x00400000 0x00b00000>; |
| label = "NOR JFFS2 Root File System"; |
| }; |
| |
| partition@f00000 { |
| /* This location must not be altered */ |
| /* 512KB for u-boot Bootloader Image */ |
| /* 512KB for u-boot Environment Variables */ |
| reg = <0x00f00000 0x00100000>; |
| label = "NOR U-Boot Image"; |
| read-only; |
| }; |
| }; |
| |
| nand@1,0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,p1025-fcm-nand", |
| "fsl,elbc-fcm-nand"; |
| reg = <0x1 0x0 0x40000>; |
| |
| partition@0 { |
| /* This location must not be altered */ |
| /* 1MB for u-boot Bootloader Image */ |
| reg = <0x0 0x00100000>; |
| label = "NAND U-Boot Image"; |
| read-only; |
| }; |
| |
| partition@100000 { |
| /* 1MB for DTB Image */ |
| reg = <0x00100000 0x00100000>; |
| label = "NAND DTB Image"; |
| }; |
| |
| partition@200000 { |
| /* 4MB for Linux Kernel Image */ |
| reg = <0x00200000 0x00400000>; |
| label = "NAND Linux Kernel Image"; |
| }; |
| |
| partition@600000 { |
| /* 4MB for Compressed Root file System Image */ |
| reg = <0x00600000 0x00400000>; |
| label = "NAND Compressed RFS Image"; |
| }; |
| |
| partition@a00000 { |
| /* 7MB for JFFS2 based Root file System */ |
| reg = <0x00a00000 0x00700000>; |
| label = "NAND JFFS2 Root File System"; |
| }; |
| |
| partition@1100000 { |
| /* 15MB for JFFS2 based Root file System */ |
| reg = <0x01100000 0x00f00000>; |
| label = "NAND Writable User area"; |
| }; |
| }; |
| |
| }; |
| |
| &soc { |
| i2c@3000 { |
| rtc@68 { |
| compatible = "dallas,ds1339"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| spi@7000 { |
| flash@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "spansion,s25sl12801"; |
| reg = <0>; |
| spi-max-frequency = <40000000>; /* input clock */ |
| |
| partition@u-boot { |
| /* 512KB for u-boot Bootloader Image */ |
| reg = <0x0 0x00080000>; |
| label = "u-boot"; |
| read-only; |
| }; |
| |
| partition@dtb { |
| /* 512KB for DTB Image */ |
| reg = <0x00080000 0x00080000>; |
| label = "dtb"; |
| }; |
| |
| partition@kernel { |
| /* 4MB for Linux Kernel Image */ |
| reg = <0x00100000 0x00400000>; |
| label = "kernel"; |
| }; |
| |
| partition@fs { |
| /* 4MB for Compressed RFS Image */ |
| reg = <0x00500000 0x00400000>; |
| label = "file system"; |
| }; |
| |
| partition@jffs-fs { |
| /* 7MB for JFFS2 based RFS */ |
| reg = <0x00900000 0x00700000>; |
| label = "file system jffs2"; |
| }; |
| }; |
| }; |
| |
| usb@22000 { |
| phy_type = "ulpi"; |
| }; |
| |
| /* USB2 is shared with localbus, so it must be disabled |
| by default. We can't put 'status = "disabled";' here |
| since U-Boot doesn't clear the status property when |
| it enables USB2. OTOH, U-Boot does create a new node |
| when there isn't any. So, just comment it out. |
| usb@23000 { |
| phy_type = "ulpi"; |
| }; |
| */ |
| |
| mdio@24000 { |
| phy0: ethernet-phy@0 { |
| interrupt-parent = <&mpic>; |
| interrupts = <3 1>; |
| reg = <0x0>; |
| }; |
| |
| phy1: ethernet-phy@1 { |
| interrupt-parent = <&mpic>; |
| interrupts = <2 1>; |
| reg = <0x1>; |
| }; |
| |
| tbi0: tbi-phy@11 { |
| reg = <0x11>; |
| device_type = "tbi-phy"; |
| }; |
| }; |
| |
| mdio@25000 { |
| tbi1: tbi-phy@11 { |
| reg = <0x11>; |
| device_type = "tbi-phy"; |
| }; |
| }; |
| |
| mdio@26000 { |
| tbi2: tbi-phy@11 { |
| reg = <0x11>; |
| device_type = "tbi-phy"; |
| }; |
| }; |
| |
| enet0: ethernet@b0000 { |
| fixed-link = <1 1 1000 0 0>; |
| phy-connection-type = "rgmii-id"; |
| |
| }; |
| |
| enet1: ethernet@b1000 { |
| phy-handle = <&phy0>; |
| tbi-handle = <&tbi1>; |
| phy-connection-type = "sgmii"; |
| }; |
| |
| enet2: ethernet@b2000 { |
| phy-handle = <&phy1>; |
| phy-connection-type = "rgmii-id"; |
| }; |
| |
| par_io@e0100 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0xe0100 0x60>; |
| ranges = <0x0 0xe0100 0x60>; |
| device_type = "par_io"; |
| num-ports = <3>; |
| pio1: ucc_pin@01 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ |
| 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */ |
| 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */ |
| 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */ |
| 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */ |
| 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */ |
| 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */ |
| 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */ |
| 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */ |
| 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */ |
| 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */ |
| 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */ |
| 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */ |
| 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */ |
| 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */ |
| 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */ |
| 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */ |
| 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */ |
| }; |
| |
| pio2: ucc_pin@02 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ |
| 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */ |
| 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */ |
| 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */ |
| 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */ |
| 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */ |
| 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */ |
| 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */ |
| 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */ |
| 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */ |
| }; |
| |
| pio3: ucc_pin@03 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/ |
| 0x0 0x12 0x2 0x0 0x2 0x0 /* SER7_CTS_B*/ |
| 0x0 0x13 0x1 0x0 0x2 0x0 /* SER7_RTS_B*/ |
| 0x0 0x14 0x2 0x0 0x2 0x0 /* SER7_RXD0*/ |
| 0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/ |
| }; |
| |
| pio4: ucc_pin@04 { |
| pio-map = < |
| /* port pin dir open_drain assignment has_irq */ |
| 0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/ |
| 0x0 0x1c 0x2 0x0 0x2 0x0 /* SER3_CTS_B*/ |
| 0x0 0x1d 0x1 0x0 0x2 0x0 /* SER3_RTS_B*/ |
| 0x0 0x1e 0x2 0x0 0x2 0x0 /* SER3_RXD0*/ |
| 0x0 0x1f 0x1 0x0 0x2 0x0>; /* SER3_TXD0*/ |
| }; |
| }; |
| }; |
| |
| &qe { |
| serial2: ucc@2600 { |
| device_type = "serial"; |
| compatible = "ucc_uart"; |
| port-number = <0>; |
| rx-clock-name = "brg6"; |
| tx-clock-name = "brg6"; |
| pio-handle = <&pio3>; |
| }; |
| |
| serial3: ucc@2200 { |
| device_type = "serial"; |
| compatible = "ucc_uart"; |
| port-number = <1>; |
| rx-clock-name = "brg2"; |
| tx-clock-name = "brg2"; |
| pio-handle = <&pio4>; |
| }; |
| }; |
