|  | /* | 
|  | * adv7183.c Analog Devices ADV7183 video decoder driver | 
|  | * | 
|  | * Copyright (c) 2011 Analog Devices Inc. | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License version 2 as | 
|  | * published by the Free Software Foundation. | 
|  | * | 
|  | * This program is distributed in the hope that it will be useful, | 
|  | * but WITHOUT ANY WARRANTY; without even the implied warranty of | 
|  | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the | 
|  | * GNU General Public License for more details. | 
|  | */ | 
|  |  | 
|  | #include <linux/delay.h> | 
|  | #include <linux/errno.h> | 
|  | #include <linux/gpio.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/slab.h> | 
|  | #include <linux/types.h> | 
|  | #include <linux/videodev2.h> | 
|  |  | 
|  | #include <media/i2c/adv7183.h> | 
|  | #include <media/v4l2-ctrls.h> | 
|  | #include <media/v4l2-device.h> | 
|  |  | 
|  | #include "adv7183_regs.h" | 
|  |  | 
|  | struct adv7183 { | 
|  | struct v4l2_subdev sd; | 
|  | struct v4l2_ctrl_handler hdl; | 
|  |  | 
|  | v4l2_std_id std; /* Current set standard */ | 
|  | u32 input; | 
|  | u32 output; | 
|  | unsigned reset_pin; | 
|  | unsigned oe_pin; | 
|  | struct v4l2_mbus_framefmt fmt; | 
|  | }; | 
|  |  | 
|  | /* EXAMPLES USING 27 MHz CLOCK | 
|  | * Mode 1 CVBS Input (Composite Video on AIN5) | 
|  | * All standards are supported through autodetect, 8-bit, 4:2:2, ITU-R BT.656 output on P15 to P8. | 
|  | */ | 
|  | static const unsigned char adv7183_init_regs[] = { | 
|  | ADV7183_IN_CTRL, 0x04,           /* CVBS input on AIN5 */ | 
|  | ADV7183_DIGI_CLAMP_CTRL_1, 0x00, /* Slow down digital clamps */ | 
|  | ADV7183_SHAP_FILT_CTRL, 0x41,    /* Set CSFM to SH1 */ | 
|  | ADV7183_ADC_CTRL, 0x16,          /* Power down ADC 1 and ADC 2 */ | 
|  | ADV7183_CTI_DNR_CTRL_4, 0x04,    /* Set DNR threshold to 4 for flat response */ | 
|  | /* ADI recommended programming sequence */ | 
|  | ADV7183_ADI_CTRL, 0x80, | 
|  | ADV7183_CTI_DNR_CTRL_4, 0x20, | 
|  | 0x52, 0x18, | 
|  | 0x58, 0xED, | 
|  | 0x77, 0xC5, | 
|  | 0x7C, 0x93, | 
|  | 0x7D, 0x00, | 
|  | 0xD0, 0x48, | 
|  | 0xD5, 0xA0, | 
|  | 0xD7, 0xEA, | 
|  | ADV7183_SD_SATURATION_CR, 0x3E, | 
|  | ADV7183_PAL_V_END, 0x3E, | 
|  | ADV7183_PAL_F_TOGGLE, 0x0F, | 
|  | ADV7183_ADI_CTRL, 0x00, | 
|  | }; | 
|  |  | 
|  | static inline struct adv7183 *to_adv7183(struct v4l2_subdev *sd) | 
|  | { | 
|  | return container_of(sd, struct adv7183, sd); | 
|  | } | 
|  | static inline struct v4l2_subdev *to_sd(struct v4l2_ctrl *ctrl) | 
|  | { | 
|  | return &container_of(ctrl->handler, struct adv7183, hdl)->sd; | 
|  | } | 
|  |  | 
|  | static inline int adv7183_read(struct v4l2_subdev *sd, unsigned char reg) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  |  | 
|  | return i2c_smbus_read_byte_data(client, reg); | 
|  | } | 
|  |  | 
|  | static inline int adv7183_write(struct v4l2_subdev *sd, unsigned char reg, | 
|  | unsigned char value) | 
|  | { | 
|  | struct i2c_client *client = v4l2_get_subdevdata(sd); | 
|  |  | 
|  | return i2c_smbus_write_byte_data(client, reg, value); | 
|  | } | 
|  |  | 
|  | static int adv7183_writeregs(struct v4l2_subdev *sd, | 
|  | const unsigned char *regs, unsigned int num) | 
|  | { | 
|  | unsigned char reg, data; | 
|  | unsigned int cnt = 0; | 
|  |  | 
|  | if (num & 0x1) { | 
|  | v4l2_err(sd, "invalid regs array\n"); | 
|  | return -1; | 
|  | } | 
|  |  | 
|  | while (cnt < num) { | 
|  | reg = *regs++; | 
|  | data = *regs++; | 
|  | cnt += 2; | 
|  |  | 
|  | adv7183_write(sd, reg, data); | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_log_status(struct v4l2_subdev *sd) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  |  | 
|  | v4l2_info(sd, "adv7183: Input control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_IN_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Video selection = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_VD_SEL)); | 
|  | v4l2_info(sd, "adv7183: Output control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_OUT_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Extended output control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_EXT_OUT_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Autodetect enable = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_AUTO_DET_EN)); | 
|  | v4l2_info(sd, "adv7183: Contrast = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_CONTRAST)); | 
|  | v4l2_info(sd, "adv7183: Brightness = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_BRIGHTNESS)); | 
|  | v4l2_info(sd, "adv7183: Hue = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_HUE)); | 
|  | v4l2_info(sd, "adv7183: Default value Y = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_DEF_Y)); | 
|  | v4l2_info(sd, "adv7183: Default value C = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_DEF_C)); | 
|  | v4l2_info(sd, "adv7183: ADI control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_ADI_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Power Management = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_POW_MANAGE)); | 
|  | v4l2_info(sd, "adv7183: Status 1 2 and 3 = 0x%02x 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_STATUS_1), | 
|  | adv7183_read(sd, ADV7183_STATUS_2), | 
|  | adv7183_read(sd, ADV7183_STATUS_3)); | 
|  | v4l2_info(sd, "adv7183: Ident = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_IDENT)); | 
|  | v4l2_info(sd, "adv7183: Analog clamp control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_ANAL_CLAMP_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Digital clamp control 1 = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_DIGI_CLAMP_CTRL_1)); | 
|  | v4l2_info(sd, "adv7183: Shaping filter control 1 and 2 = 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_SHAP_FILT_CTRL), | 
|  | adv7183_read(sd, ADV7183_SHAP_FILT_CTRL_2)); | 
|  | v4l2_info(sd, "adv7183: Comb filter control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_COMB_FILT_CTRL)); | 
|  | v4l2_info(sd, "adv7183: ADI control 2 = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_ADI_CTRL_2)); | 
|  | v4l2_info(sd, "adv7183: Pixel delay control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_PIX_DELAY_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Misc gain control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_MISC_GAIN_CTRL)); | 
|  | v4l2_info(sd, "adv7183: AGC mode control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_AGC_MODE_CTRL)); | 
|  | v4l2_info(sd, "adv7183: Chroma gain control 1 and 2 = 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_CHRO_GAIN_CTRL_1), | 
|  | adv7183_read(sd, ADV7183_CHRO_GAIN_CTRL_2)); | 
|  | v4l2_info(sd, "adv7183: Luma gain control 1 and 2 = 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_LUMA_GAIN_CTRL_1), | 
|  | adv7183_read(sd, ADV7183_LUMA_GAIN_CTRL_2)); | 
|  | v4l2_info(sd, "adv7183: Vsync field control 1 2 and 3 = 0x%02x 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_VS_FIELD_CTRL_1), | 
|  | adv7183_read(sd, ADV7183_VS_FIELD_CTRL_2), | 
|  | adv7183_read(sd, ADV7183_VS_FIELD_CTRL_3)); | 
|  | v4l2_info(sd, "adv7183: Hsync position control 1 2 and 3 = 0x%02x 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_HS_POS_CTRL_1), | 
|  | adv7183_read(sd, ADV7183_HS_POS_CTRL_2), | 
|  | adv7183_read(sd, ADV7183_HS_POS_CTRL_3)); | 
|  | v4l2_info(sd, "adv7183: Polarity = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_POLARITY)); | 
|  | v4l2_info(sd, "adv7183: ADC control = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_ADC_CTRL)); | 
|  | v4l2_info(sd, "adv7183: SD offset Cb and Cr = 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_SD_OFFSET_CB), | 
|  | adv7183_read(sd, ADV7183_SD_OFFSET_CR)); | 
|  | v4l2_info(sd, "adv7183: SD saturation Cb and Cr = 0x%02x 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_SD_SATURATION_CB), | 
|  | adv7183_read(sd, ADV7183_SD_SATURATION_CR)); | 
|  | v4l2_info(sd, "adv7183: Drive strength = 0x%02x\n", | 
|  | adv7183_read(sd, ADV7183_DRIVE_STR)); | 
|  | v4l2_ctrl_handler_log_status(&decoder->hdl, sd->name); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_g_std(struct v4l2_subdev *sd, v4l2_std_id *std) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  |  | 
|  | *std = decoder->std; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_s_std(struct v4l2_subdev *sd, v4l2_std_id std) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  | int reg; | 
|  |  | 
|  | reg = adv7183_read(sd, ADV7183_IN_CTRL) & 0xF; | 
|  | if (std == V4L2_STD_PAL_60) | 
|  | reg |= 0x60; | 
|  | else if (std == V4L2_STD_NTSC_443) | 
|  | reg |= 0x70; | 
|  | else if (std == V4L2_STD_PAL_N) | 
|  | reg |= 0x90; | 
|  | else if (std == V4L2_STD_PAL_M) | 
|  | reg |= 0xA0; | 
|  | else if (std == V4L2_STD_PAL_Nc) | 
|  | reg |= 0xC0; | 
|  | else if (std & V4L2_STD_PAL) | 
|  | reg |= 0x80; | 
|  | else if (std & V4L2_STD_NTSC) | 
|  | reg |= 0x50; | 
|  | else if (std & V4L2_STD_SECAM) | 
|  | reg |= 0xE0; | 
|  | else | 
|  | return -EINVAL; | 
|  | adv7183_write(sd, ADV7183_IN_CTRL, reg); | 
|  |  | 
|  | decoder->std = std; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_reset(struct v4l2_subdev *sd, u32 val) | 
|  | { | 
|  | int reg; | 
|  |  | 
|  | reg = adv7183_read(sd, ADV7183_POW_MANAGE) | 0x80; | 
|  | adv7183_write(sd, ADV7183_POW_MANAGE, reg); | 
|  | /* wait 5ms before any further i2c writes are performed */ | 
|  | usleep_range(5000, 10000); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_s_routing(struct v4l2_subdev *sd, | 
|  | u32 input, u32 output, u32 config) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  | int reg; | 
|  |  | 
|  | if ((input > ADV7183_COMPONENT1) || (output > ADV7183_16BIT_OUT)) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (input != decoder->input) { | 
|  | decoder->input = input; | 
|  | reg = adv7183_read(sd, ADV7183_IN_CTRL) & 0xF0; | 
|  | switch (input) { | 
|  | case ADV7183_COMPOSITE1: | 
|  | reg |= 0x1; | 
|  | break; | 
|  | case ADV7183_COMPOSITE2: | 
|  | reg |= 0x2; | 
|  | break; | 
|  | case ADV7183_COMPOSITE3: | 
|  | reg |= 0x3; | 
|  | break; | 
|  | case ADV7183_COMPOSITE4: | 
|  | reg |= 0x4; | 
|  | break; | 
|  | case ADV7183_COMPOSITE5: | 
|  | reg |= 0x5; | 
|  | break; | 
|  | case ADV7183_COMPOSITE6: | 
|  | reg |= 0xB; | 
|  | break; | 
|  | case ADV7183_COMPOSITE7: | 
|  | reg |= 0xC; | 
|  | break; | 
|  | case ADV7183_COMPOSITE8: | 
|  | reg |= 0xD; | 
|  | break; | 
|  | case ADV7183_COMPOSITE9: | 
|  | reg |= 0xE; | 
|  | break; | 
|  | case ADV7183_COMPOSITE10: | 
|  | reg |= 0xF; | 
|  | break; | 
|  | case ADV7183_SVIDEO0: | 
|  | reg |= 0x6; | 
|  | break; | 
|  | case ADV7183_SVIDEO1: | 
|  | reg |= 0x7; | 
|  | break; | 
|  | case ADV7183_SVIDEO2: | 
|  | reg |= 0x8; | 
|  | break; | 
|  | case ADV7183_COMPONENT0: | 
|  | reg |= 0x9; | 
|  | break; | 
|  | case ADV7183_COMPONENT1: | 
|  | reg |= 0xA; | 
|  | break; | 
|  | default: | 
|  | break; | 
|  | } | 
|  | adv7183_write(sd, ADV7183_IN_CTRL, reg); | 
|  | } | 
|  |  | 
|  | if (output != decoder->output) { | 
|  | decoder->output = output; | 
|  | reg = adv7183_read(sd, ADV7183_OUT_CTRL) & 0xC0; | 
|  | switch (output) { | 
|  | case ADV7183_16BIT_OUT: | 
|  | reg |= 0x9; | 
|  | break; | 
|  | default: | 
|  | reg |= 0xC; | 
|  | break; | 
|  | } | 
|  | adv7183_write(sd, ADV7183_OUT_CTRL, reg); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_s_ctrl(struct v4l2_ctrl *ctrl) | 
|  | { | 
|  | struct v4l2_subdev *sd = to_sd(ctrl); | 
|  | int val = ctrl->val; | 
|  |  | 
|  | switch (ctrl->id) { | 
|  | case V4L2_CID_BRIGHTNESS: | 
|  | if (val < 0) | 
|  | val = 127 - val; | 
|  | adv7183_write(sd, ADV7183_BRIGHTNESS, val); | 
|  | break; | 
|  | case V4L2_CID_CONTRAST: | 
|  | adv7183_write(sd, ADV7183_CONTRAST, val); | 
|  | break; | 
|  | case V4L2_CID_SATURATION: | 
|  | adv7183_write(sd, ADV7183_SD_SATURATION_CB, val >> 8); | 
|  | adv7183_write(sd, ADV7183_SD_SATURATION_CR, (val & 0xFF)); | 
|  | break; | 
|  | case V4L2_CID_HUE: | 
|  | adv7183_write(sd, ADV7183_SD_OFFSET_CB, val >> 8); | 
|  | adv7183_write(sd, ADV7183_SD_OFFSET_CR, (val & 0xFF)); | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  | int reg; | 
|  |  | 
|  | /* enable autodetection block */ | 
|  | reg = adv7183_read(sd, ADV7183_IN_CTRL) & 0xF; | 
|  | adv7183_write(sd, ADV7183_IN_CTRL, reg); | 
|  |  | 
|  | /* wait autodetection switch */ | 
|  | mdelay(10); | 
|  |  | 
|  | /* get autodetection result */ | 
|  | reg = adv7183_read(sd, ADV7183_STATUS_1); | 
|  | switch ((reg >> 0x4) & 0x7) { | 
|  | case 0: | 
|  | *std &= V4L2_STD_NTSC; | 
|  | break; | 
|  | case 1: | 
|  | *std &= V4L2_STD_NTSC_443; | 
|  | break; | 
|  | case 2: | 
|  | *std &= V4L2_STD_PAL_M; | 
|  | break; | 
|  | case 3: | 
|  | *std &= V4L2_STD_PAL_60; | 
|  | break; | 
|  | case 4: | 
|  | *std &= V4L2_STD_PAL; | 
|  | break; | 
|  | case 5: | 
|  | *std &= V4L2_STD_SECAM; | 
|  | break; | 
|  | case 6: | 
|  | *std &= V4L2_STD_PAL_Nc; | 
|  | break; | 
|  | case 7: | 
|  | *std &= V4L2_STD_SECAM; | 
|  | break; | 
|  | default: | 
|  | *std = V4L2_STD_UNKNOWN; | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* after std detection, write back user set std */ | 
|  | adv7183_s_std(sd, decoder->std); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_g_input_status(struct v4l2_subdev *sd, u32 *status) | 
|  | { | 
|  | int reg; | 
|  |  | 
|  | *status = V4L2_IN_ST_NO_SIGNAL; | 
|  | reg = adv7183_read(sd, ADV7183_STATUS_1); | 
|  | if (reg < 0) | 
|  | return reg; | 
|  | if (reg & 0x1) | 
|  | *status = 0; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_enum_mbus_code(struct v4l2_subdev *sd, | 
|  | struct v4l2_subdev_pad_config *cfg, | 
|  | struct v4l2_subdev_mbus_code_enum *code) | 
|  | { | 
|  | if (code->pad || code->index > 0) | 
|  | return -EINVAL; | 
|  |  | 
|  | code->code = MEDIA_BUS_FMT_UYVY8_2X8; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_set_fmt(struct v4l2_subdev *sd, | 
|  | struct v4l2_subdev_pad_config *cfg, | 
|  | struct v4l2_subdev_format *format) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  | struct v4l2_mbus_framefmt *fmt = &format->format; | 
|  |  | 
|  | if (format->pad) | 
|  | return -EINVAL; | 
|  |  | 
|  | fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; | 
|  | fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; | 
|  | if (decoder->std & V4L2_STD_525_60) { | 
|  | fmt->field = V4L2_FIELD_SEQ_TB; | 
|  | fmt->width = 720; | 
|  | fmt->height = 480; | 
|  | } else { | 
|  | fmt->field = V4L2_FIELD_SEQ_BT; | 
|  | fmt->width = 720; | 
|  | fmt->height = 576; | 
|  | } | 
|  | if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) | 
|  | decoder->fmt = *fmt; | 
|  | else | 
|  | cfg->try_fmt = *fmt; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_get_fmt(struct v4l2_subdev *sd, | 
|  | struct v4l2_subdev_pad_config *cfg, | 
|  | struct v4l2_subdev_format *format) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  |  | 
|  | if (format->pad) | 
|  | return -EINVAL; | 
|  |  | 
|  | format->format = decoder->fmt; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_s_stream(struct v4l2_subdev *sd, int enable) | 
|  | { | 
|  | struct adv7183 *decoder = to_adv7183(sd); | 
|  |  | 
|  | if (enable) | 
|  | gpio_set_value(decoder->oe_pin, 0); | 
|  | else | 
|  | gpio_set_value(decoder->oe_pin, 1); | 
|  | udelay(1); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | #ifdef CONFIG_VIDEO_ADV_DEBUG | 
|  | static int adv7183_g_register(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg) | 
|  | { | 
|  | reg->val = adv7183_read(sd, reg->reg & 0xff); | 
|  | reg->size = 1; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_s_register(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg) | 
|  | { | 
|  | adv7183_write(sd, reg->reg & 0xff, reg->val & 0xff); | 
|  | return 0; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | static const struct v4l2_ctrl_ops adv7183_ctrl_ops = { | 
|  | .s_ctrl = adv7183_s_ctrl, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_core_ops adv7183_core_ops = { | 
|  | .log_status = adv7183_log_status, | 
|  | .reset = adv7183_reset, | 
|  | #ifdef CONFIG_VIDEO_ADV_DEBUG | 
|  | .g_register = adv7183_g_register, | 
|  | .s_register = adv7183_s_register, | 
|  | #endif | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_video_ops adv7183_video_ops = { | 
|  | .g_std = adv7183_g_std, | 
|  | .s_std = adv7183_s_std, | 
|  | .s_routing = adv7183_s_routing, | 
|  | .querystd = adv7183_querystd, | 
|  | .g_input_status = adv7183_g_input_status, | 
|  | .s_stream = adv7183_s_stream, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_pad_ops adv7183_pad_ops = { | 
|  | .enum_mbus_code = adv7183_enum_mbus_code, | 
|  | .get_fmt = adv7183_get_fmt, | 
|  | .set_fmt = adv7183_set_fmt, | 
|  | }; | 
|  |  | 
|  | static const struct v4l2_subdev_ops adv7183_ops = { | 
|  | .core = &adv7183_core_ops, | 
|  | .video = &adv7183_video_ops, | 
|  | .pad = &adv7183_pad_ops, | 
|  | }; | 
|  |  | 
|  | static int adv7183_probe(struct i2c_client *client, | 
|  | const struct i2c_device_id *id) | 
|  | { | 
|  | struct adv7183 *decoder; | 
|  | struct v4l2_subdev *sd; | 
|  | struct v4l2_ctrl_handler *hdl; | 
|  | int ret; | 
|  | struct v4l2_subdev_format fmt = { | 
|  | .which = V4L2_SUBDEV_FORMAT_ACTIVE, | 
|  | }; | 
|  | const unsigned *pin_array; | 
|  |  | 
|  | /* Check if the adapter supports the needed features */ | 
|  | if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) | 
|  | return -EIO; | 
|  |  | 
|  | v4l_info(client, "chip found @ 0x%02x (%s)\n", | 
|  | client->addr << 1, client->adapter->name); | 
|  |  | 
|  | pin_array = client->dev.platform_data; | 
|  | if (pin_array == NULL) | 
|  | return -EINVAL; | 
|  |  | 
|  | decoder = devm_kzalloc(&client->dev, sizeof(*decoder), GFP_KERNEL); | 
|  | if (decoder == NULL) | 
|  | return -ENOMEM; | 
|  |  | 
|  | decoder->reset_pin = pin_array[0]; | 
|  | decoder->oe_pin = pin_array[1]; | 
|  |  | 
|  | if (devm_gpio_request_one(&client->dev, decoder->reset_pin, | 
|  | GPIOF_OUT_INIT_LOW, "ADV7183 Reset")) { | 
|  | v4l_err(client, "failed to request GPIO %d\n", decoder->reset_pin); | 
|  | return -EBUSY; | 
|  | } | 
|  |  | 
|  | if (devm_gpio_request_one(&client->dev, decoder->oe_pin, | 
|  | GPIOF_OUT_INIT_HIGH, | 
|  | "ADV7183 Output Enable")) { | 
|  | v4l_err(client, "failed to request GPIO %d\n", decoder->oe_pin); | 
|  | return -EBUSY; | 
|  | } | 
|  |  | 
|  | sd = &decoder->sd; | 
|  | v4l2_i2c_subdev_init(sd, client, &adv7183_ops); | 
|  |  | 
|  | hdl = &decoder->hdl; | 
|  | v4l2_ctrl_handler_init(hdl, 4); | 
|  | v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | 
|  | V4L2_CID_BRIGHTNESS, -128, 127, 1, 0); | 
|  | v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | 
|  | V4L2_CID_CONTRAST, 0, 0xFF, 1, 0x80); | 
|  | v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | 
|  | V4L2_CID_SATURATION, 0, 0xFFFF, 1, 0x8080); | 
|  | v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | 
|  | V4L2_CID_HUE, 0, 0xFFFF, 1, 0x8080); | 
|  | /* hook the control handler into the driver */ | 
|  | sd->ctrl_handler = hdl; | 
|  | if (hdl->error) { | 
|  | ret = hdl->error; | 
|  |  | 
|  | v4l2_ctrl_handler_free(hdl); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* v4l2 doesn't support an autodetect standard, pick PAL as default */ | 
|  | decoder->std = V4L2_STD_PAL; | 
|  | decoder->input = ADV7183_COMPOSITE4; | 
|  | decoder->output = ADV7183_8BIT_OUT; | 
|  |  | 
|  | /* reset chip */ | 
|  | /* reset pulse width at least 5ms */ | 
|  | mdelay(10); | 
|  | gpio_set_value(decoder->reset_pin, 1); | 
|  | /* wait 5ms before any further i2c writes are performed */ | 
|  | mdelay(5); | 
|  |  | 
|  | adv7183_writeregs(sd, adv7183_init_regs, ARRAY_SIZE(adv7183_init_regs)); | 
|  | adv7183_s_std(sd, decoder->std); | 
|  | fmt.format.width = 720; | 
|  | fmt.format.height = 576; | 
|  | adv7183_set_fmt(sd, NULL, &fmt); | 
|  |  | 
|  | /* initialize the hardware to the default control values */ | 
|  | ret = v4l2_ctrl_handler_setup(hdl); | 
|  | if (ret) { | 
|  | v4l2_ctrl_handler_free(hdl); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int adv7183_remove(struct i2c_client *client) | 
|  | { | 
|  | struct v4l2_subdev *sd = i2c_get_clientdata(client); | 
|  |  | 
|  | v4l2_device_unregister_subdev(sd); | 
|  | v4l2_ctrl_handler_free(sd->ctrl_handler); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct i2c_device_id adv7183_id[] = { | 
|  | {"adv7183", 0}, | 
|  | {}, | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(i2c, adv7183_id); | 
|  |  | 
|  | static struct i2c_driver adv7183_driver = { | 
|  | .driver = { | 
|  | .name   = "adv7183", | 
|  | }, | 
|  | .probe          = adv7183_probe, | 
|  | .remove         = adv7183_remove, | 
|  | .id_table       = adv7183_id, | 
|  | }; | 
|  |  | 
|  | module_i2c_driver(adv7183_driver); | 
|  |  | 
|  | MODULE_DESCRIPTION("Analog Devices ADV7183 video decoder driver"); | 
|  | MODULE_AUTHOR("Scott Jiang <Scott.Jiang.Linux@gmail.com>"); | 
|  | MODULE_LICENSE("GPL v2"); |