| Kernel driver ads1015 | 
 | ===================== | 
 |  | 
 | Supported chips: | 
 |   * Texas Instruments ADS1015 | 
 |     Prefix: 'ads1015' | 
 |     Datasheet: Publicly available at the Texas Instruments website : | 
 |                http://focus.ti.com/lit/ds/symlink/ads1015.pdf | 
 |   * Texas Instruments ADS1115 | 
 |     Prefix: 'ads1115' | 
 |     Datasheet: Publicly available at the Texas Instruments website : | 
 |                http://focus.ti.com/lit/ds/symlink/ads1115.pdf | 
 |  | 
 | Authors: | 
 |         Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de> | 
 |  | 
 | Description | 
 | ----------- | 
 |  | 
 | This driver implements support for the Texas Instruments ADS1015/ADS1115. | 
 |  | 
 | This device is a 12/16-bit A-D converter with 4 inputs. | 
 |  | 
 | The inputs can be used single ended or in certain differential combinations. | 
 |  | 
 | The inputs can be made available by 8 sysfs input files in0_input - in7_input: | 
 | in0: Voltage over AIN0 and AIN1. | 
 | in1: Voltage over AIN0 and AIN3. | 
 | in2: Voltage over AIN1 and AIN3. | 
 | in3: Voltage over AIN2 and AIN3. | 
 | in4: Voltage over AIN0 and GND. | 
 | in5: Voltage over AIN1 and GND. | 
 | in6: Voltage over AIN2 and GND. | 
 | in7: Voltage over AIN3 and GND. | 
 |  | 
 | Which inputs are available can be configured using platform data or devicetree. | 
 |  | 
 | By default all inputs are exported. | 
 |  | 
 | Platform Data | 
 | ------------- | 
 |  | 
 | In linux/platform_data/ads1015.h platform data is defined, channel_data contains | 
 | configuration data for the used input combinations: | 
 | - pga is the programmable gain amplifier (values are full scale) | 
 |   0: +/- 6.144 V | 
 |   1: +/- 4.096 V | 
 |   2: +/- 2.048 V | 
 |   3: +/- 1.024 V | 
 |   4: +/- 0.512 V | 
 |   5: +/- 0.256 V | 
 | - data_rate in samples per second | 
 |   0: 128 | 
 |   1: 250 | 
 |   2: 490 | 
 |   3: 920 | 
 |   4: 1600 | 
 |   5: 2400 | 
 |   6: 3300 | 
 |  | 
 | Example: | 
 | struct ads1015_platform_data data = { | 
 | 	.channel_data = { | 
 | 		[2] = { .enabled = true, .pga = 1, .data_rate = 0 }, | 
 | 		[4] = { .enabled = true, .pga = 4, .data_rate = 5 }, | 
 | 	} | 
 | }; | 
 |  | 
 | In this case only in2_input (FS +/- 4.096 V, 128 SPS) and in4_input | 
 | (FS +/- 0.512 V, 2400 SPS) would be created. | 
 |  | 
 | Devicetree | 
 | ---------- | 
 |  | 
 | Configuration is also possible via devicetree: | 
 | Documentation/devicetree/bindings/hwmon/ads1015.txt |