| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. |
| * Copyright (c) 2024, Xilin Wu <wuxilin123@gmail.com> |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| #include "x1e80100.dtsi" |
| #include "x1e80100-pmics.dtsi" |
| |
| / { |
| model = "ASUS Vivobook S 15"; |
| compatible = "asus,vivobook-s15", "qcom,x1e80100"; |
| chassis-type = "laptop"; |
| |
| aliases { |
| serial1 = &uart14; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-0 = <&hall_int_n_default>; |
| pinctrl-names = "default"; |
| |
| switch-lid { |
| gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| wakeup-source; |
| wakeup-event-action = <EV_ACT_DEASSERTED>; |
| }; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,x1e80100-pmic-glink", |
| "qcom,sm8550-pmic-glink", |
| "qcom,pmic-glink"; |
| orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, |
| <&tlmm 123 GPIO_ACTIVE_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| /* Left-side port, closer to the screen */ |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss0_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss0_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| /* Left-side port, farther from the screen */ |
| connector@1 { |
| compatible = "usb-c-connector"; |
| reg = <1>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss1_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss1_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| linux,cma { |
| compatible = "shared-dma-pool"; |
| size = <0x0 0x8000000>; |
| reusable; |
| linux,cma-default; |
| }; |
| }; |
| |
| vreg_edp_3p3: regulator-edp-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_EDP_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&edp_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vreg_nvme: regulator-nvme { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_NVME_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&nvme_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vph_pwr: regulator-vph-pwr { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| /* |
| * TODO: These two regulators are actually part of the removable M.2 |
| * card and not the CRD mainboard. Need to describe this differently. |
| * Functionally it works correctly, because all we need to do is to |
| * turn on the actual 3.3V supply above. |
| */ |
| vreg_wcn_0p95: regulator-wcn-0p95 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_WCN_0P95"; |
| regulator-min-microvolt = <950000>; |
| regulator-max-microvolt = <950000>; |
| |
| vin-supply = <&vreg_wcn_3p3>; |
| }; |
| |
| vreg_wcn_1p9: regulator-wcn-1p9 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_WCN_1P9"; |
| regulator-min-microvolt = <1900000>; |
| regulator-max-microvolt = <1900000>; |
| |
| vin-supply = <&vreg_wcn_3p3>; |
| }; |
| |
| vreg_wcn_3p3: regulator-wcn-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_WCN_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&wcn_sw_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| wcn7850-pmu { |
| compatible = "qcom,wcn7850-pmu"; |
| |
| vdd-supply = <&vreg_wcn_0p95>; |
| vddio-supply = <&vreg_l15b_1p8>; |
| vddaon-supply = <&vreg_wcn_0p95>; |
| vdddig-supply = <&vreg_wcn_0p95>; |
| vddrfa1p2-supply = <&vreg_wcn_1p9>; |
| vddrfa1p8-supply = <&vreg_wcn_1p9>; |
| |
| wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>; |
| bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&wcn_wlan_en>, <&wcn_bt_en>; |
| pinctrl-names = "default"; |
| |
| regulators { |
| vreg_pmu_rfa_cmn: ldo0 { |
| regulator-name = "vreg_pmu_rfa_cmn"; |
| }; |
| |
| vreg_pmu_aon_0p59: ldo1 { |
| regulator-name = "vreg_pmu_aon_0p59"; |
| }; |
| |
| vreg_pmu_wlcx_0p8: ldo2 { |
| regulator-name = "vreg_pmu_wlcx_0p8"; |
| }; |
| |
| vreg_pmu_wlmx_0p85: ldo3 { |
| regulator-name = "vreg_pmu_wlmx_0p85"; |
| }; |
| |
| vreg_pmu_btcmx_0p85: ldo4 { |
| regulator-name = "vreg_pmu_btcmx_0p85"; |
| }; |
| |
| vreg_pmu_rfa_0p8: ldo5 { |
| regulator-name = "vreg_pmu_rfa_0p8"; |
| }; |
| |
| vreg_pmu_rfa_1p2: ldo6 { |
| regulator-name = "vreg_pmu_rfa_1p2"; |
| }; |
| |
| vreg_pmu_rfa_1p8: ldo7 { |
| regulator-name = "vreg_pmu_rfa_1p8"; |
| }; |
| |
| vreg_pmu_pcie_0p9: ldo8 { |
| regulator-name = "vreg_pmu_pcie_0p9"; |
| }; |
| |
| vreg_pmu_pcie_1p8: ldo9 { |
| regulator-name = "vreg_pmu_pcie_1p8"; |
| }; |
| }; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8550-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-bob1-supply = <&vph_pwr>; |
| vdd-bob2-supply = <&vph_pwr>; |
| vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; |
| vdd-l2-l13-l14-supply = <&vreg_bob1>; |
| vdd-l5-l16-supply = <&vreg_bob1>; |
| vdd-l6-l7-supply = <&vreg_bob2>; |
| vdd-l8-l9-supply = <&vreg_bob1>; |
| vdd-l12-supply = <&vreg_s5j_1p2>; |
| vdd-l15-supply = <&vreg_s4c_1p8>; |
| vdd-l17-supply = <&vreg_bob2>; |
| |
| vreg_bob1: bob1 { |
| regulator-name = "vreg_bob1"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob2: bob2 { |
| regulator-name = "vreg_bob2"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_3p0: ldo2 { |
| regulator-name = "vreg_l2b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4b_1p8: ldo4 { |
| regulator-name = "vreg_l4b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13b_3p0: ldo13 { |
| regulator-name = "vreg_l13b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b_3p0: ldo14 { |
| regulator-name = "vreg_l14b_3p0"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b_1p8: ldo15 { |
| regulator-name = "vreg_l15b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-l1-supply = <&vreg_s5j_1p2>; |
| vdd-l2-supply = <&vreg_s1f_0p7>; |
| vdd-l3-supply = <&vreg_s1f_0p7>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| vreg_l3c_0p8: ldo3 { |
| regulator-name = "vreg_l3c_0p8"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s4c_1p8: smps4 { |
| regulator-name = "vreg_s4c_1p8"; |
| regulator-min-microvolt = <1856000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "d"; |
| |
| vdd-l1-supply = <&vreg_s1f_0p7>; |
| vdd-l2-supply = <&vreg_s1f_0p7>; |
| vdd-l3-supply = <&vreg_s4c_1p8>; |
| vdd-s1-supply = <&vph_pwr>; |
| |
| vreg_l1d_0p8: ldo1 { |
| regulator-name = "vreg_l1d_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2d_0p9: ldo2 { |
| regulator-name = "vreg_l2d_0p9"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3d_1p8: ldo3 { |
| regulator-name = "vreg_l3d_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-3 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "e"; |
| |
| vdd-l2-supply = <&vreg_s1f_0p7>; |
| vdd-l3-supply = <&vreg_s5j_1p2>; |
| |
| vreg_l2e_0p8: ldo2 { |
| regulator-name = "vreg_l2e_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3e_1p2: ldo3 { |
| regulator-name = "vreg_l3e_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-4 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "f"; |
| |
| vdd-l1-supply = <&vreg_s5j_1p2>; |
| vdd-l2-supply = <&vreg_s5j_1p2>; |
| vdd-l3-supply = <&vreg_s5j_1p2>; |
| vdd-s1-supply = <&vph_pwr>; |
| |
| vreg_s1f_0p7: smps1 { |
| regulator-name = "vreg_s1f_0p7"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-6 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "i"; |
| |
| vdd-l1-supply = <&vreg_s4c_1p8>; |
| vdd-l2-supply = <&vreg_s5j_1p2>; |
| vdd-l3-supply = <&vreg_s1f_0p7>; |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| |
| vreg_l3i_0p8: ldo3 { |
| regulator-name = "vreg_l3i_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-7 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "j"; |
| |
| vdd-l1-supply = <&vreg_s1f_0p7>; |
| vdd-l2-supply = <&vreg_s5j_1p2>; |
| vdd-l3-supply = <&vreg_s1f_0p7>; |
| vdd-s5-supply = <&vph_pwr>; |
| |
| vreg_s5j_1p2: smps5 { |
| regulator-name = "vreg_s5j_1p2"; |
| regulator-min-microvolt = <1256000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1j_0p8: ldo1 { |
| regulator-name = "vreg_l1j_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2j_1p2: ldo2 { |
| regulator-name = "vreg_l2j_1p2"; |
| regulator-min-microvolt = <1256000>; |
| regulator-max-microvolt = <1256000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3j_0p8: ldo3 { |
| regulator-name = "vreg_l3j_0p8"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| firmware-name = "qcom/x1e80100/ASUSTeK/vivobook-s15/qcdxkmsuc8380.mbn"; |
| }; |
| }; |
| |
| &i2c0 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| touchpad@15 { |
| compatible = "hid-over-i2c"; |
| reg = <0x15>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&tpad_default>; |
| pinctrl-names = "default"; |
| |
| wakeup-source; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| /* PS8830 USB4 Retimer? @ 0x8 */ |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| /* PS8830 USB4 Retimer? @ 0x8 */ |
| }; |
| |
| &i2c5 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| keyboard@3a { |
| compatible = "hid-over-i2c"; |
| reg = <0x3a>; |
| |
| hid-descr-addr = <0x1>; |
| interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-0 = <&kybd_default>; |
| pinctrl-names = "default"; |
| |
| wakeup-source; |
| }; |
| |
| eusb5_repeater: redriver@43 { |
| compatible = "nxp,ptn3222"; |
| reg = <0x43>; |
| #phy-cells = <0>; |
| |
| vdd3v3-supply = <&vreg_l13b_3p0>; |
| vdd1v8-supply = <&vreg_l4b_1p8>; |
| |
| reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&eusb5_reset_n>; |
| pinctrl-names = "default"; |
| }; |
| |
| eusb3_repeater: redriver@47 { |
| compatible = "nxp,ptn3222"; |
| reg = <0x47>; |
| #phy-cells = <0>; |
| |
| vdd3v3-supply = <&vreg_l13b_3p0>; |
| vdd1v8-supply = <&vreg_l4b_1p8>; |
| |
| reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&eusb3_reset_n>; |
| pinctrl-names = "default"; |
| }; |
| |
| eusb6_repeater: redriver@4f { |
| compatible = "nxp,ptn3222"; |
| reg = <0x4f>; |
| #phy-cells = <0>; |
| |
| vdd3v3-supply = <&vreg_l13b_3p0>; |
| vdd1v8-supply = <&vreg_l4b_1p8>; |
| |
| reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&eusb6_reset_n>; |
| pinctrl-names = "default"; |
| }; |
| |
| /* EC @ 0x76 */ |
| }; |
| |
| &i2c7 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| /* PS8830 USB4 Retimer? @ 0x8 */ |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dp3 { |
| /delete-property/ #sound-dai-cells; |
| |
| status = "okay"; |
| |
| aux-bus { |
| panel { |
| compatible = "samsung,atna56ac03", "samsung,atna33xc20"; |
| enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>; |
| power-supply = <&vreg_edp_3p3>; |
| |
| pinctrl-0 = <&edp_bl_en>; |
| pinctrl-names = "default"; |
| |
| port { |
| edp_panel_in: endpoint { |
| remote-endpoint = <&mdss_dp3_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| |
| mdss_dp3_out: endpoint { |
| data-lanes = <0 1 2 3>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| |
| remote-endpoint = <&edp_panel_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dp3_phy { |
| vdda-phy-supply = <&vreg_l3j_0p8>; |
| vdda-pll-supply = <&vreg_l2j_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4 { |
| perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&pcie4_default>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4_phy { |
| vdda-phy-supply = <&vreg_l3i_0p8>; |
| vdda-pll-supply = <&vreg_l3e_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4_port0 { |
| wifi@0 { |
| compatible = "pci17cb,1107"; |
| reg = <0x10000 0x0 0x0 0x0 0x0>; |
| |
| vddaon-supply = <&vreg_pmu_aon_0p59>; |
| vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; |
| vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; |
| }; |
| }; |
| |
| &pcie6a { |
| perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; |
| |
| vddpe-3v3-supply = <&vreg_nvme>; |
| |
| pinctrl-0 = <&pcie6a_default>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &pcie6a_phy { |
| vdda-phy-supply = <&vreg_l1d_0p8>; |
| vdda-pll-supply = <&vreg_l2j_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pmc8380_3_gpios { |
| edp_bl_en: edp-bl-en-state { |
| pins = "gpio4"; |
| function = "normal"; |
| power-source = <1>; /* 1.8 V */ |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>; |
| bias-pull-down; |
| input-disable; |
| output-enable; |
| }; |
| }; |
| |
| &qupv3_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_1 { |
| status = "okay"; |
| }; |
| |
| &qupv3_2 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/x1e80100/ASUSTeK/vivobook-s15/qcadsp8380.mbn", |
| "qcom/x1e80100/ASUSTeK/vivobook-s15/adsp_dtbs.elf"; |
| |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/x1e80100/ASUSTeK/vivobook-s15/qccdsp8380.mbn", |
| "qcom/x1e80100/ASUSTeK/vivobook-s15/cdsp_dtbs.elf"; |
| |
| status = "okay"; |
| }; |
| |
| &smb2360_0 { |
| status = "okay"; |
| }; |
| |
| &smb2360_0_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d_1p8>; |
| vdd3-supply = <&vreg_l2b_3p0>; |
| }; |
| |
| &smb2360_1 { |
| status = "okay"; |
| }; |
| |
| &smb2360_1_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d_1p8>; |
| vdd3-supply = <&vreg_l14b_3p0>; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <34 2>, /* Unused */ |
| <44 4>, /* SPI (TPM) */ |
| <238 1>; /* UFS Reset */ |
| |
| edp_reg_en: edp-reg-en-state { |
| pins = "gpio70"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| eusb3_reset_n: eusb3-reset-n-state { |
| pins = "gpio6"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| output-low; |
| }; |
| |
| eusb5_reset_n: eusb5-reset-n-state { |
| pins = "gpio7"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| output-low; |
| }; |
| |
| eusb6_reset_n: eusb6-reset-n-state { |
| pins = "gpio184"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| output-low; |
| }; |
| |
| hall_int_n_default: hall-int-n-state { |
| pins = "gpio92"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| kybd_default: kybd-default-state { |
| pins = "gpio67"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| nvme_reg_en: nvme-reg-en-state { |
| pins = "gpio18"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| pcie4_default: pcie4-default-state { |
| clkreq-n-pins { |
| pins = "gpio147"; |
| function = "pcie4_clk"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio146"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio148"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie6a_default: pcie6a-default-state { |
| clkreq-n-pins { |
| pins = "gpio153"; |
| function = "pcie6a_clk"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| perst-n-pins { |
| pins = "gpio152"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio154"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| tpad_default: tpad-default-state { |
| pins = "gpio3"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| wcn_bt_en: wcn-bt-en-state { |
| pins = "gpio116"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-pull-down; |
| }; |
| |
| wcn_sw_en: wcn-sw-en-state { |
| pins = "gpio214"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| wcn_wlan_en: wcn-wlan-en-state { |
| pins = "gpio117"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| }; |
| |
| &uart14 { |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn7850-bt"; |
| max-speed = <3200000>; |
| |
| vddaon-supply = <&vreg_pmu_aon_0p59>; |
| vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| }; |
| }; |
| |
| &usb_1_ss0_hsphy { |
| vdd-supply = <&vreg_l3j_0p8>; |
| vdda12-supply = <&vreg_l2j_1p2>; |
| |
| phys = <&smb2360_0_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_qmpphy { |
| vdda-phy-supply = <&vreg_l2j_1p2>; |
| vdda-pll-supply = <&vreg_l1j_0p8>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss0_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss0_hs_in>; |
| }; |
| |
| &usb_1_ss0_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss0_ss_in>; |
| }; |
| |
| &usb_1_ss1_hsphy { |
| vdd-supply = <&vreg_l3j_0p8>; |
| vdda12-supply = <&vreg_l2j_1p2>; |
| |
| phys = <&smb2360_1_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1_qmpphy { |
| vdda-phy-supply = <&vreg_l2j_1p2>; |
| vdda-pll-supply = <&vreg_l2d_0p9>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss1_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss1_hs_in>; |
| }; |
| |
| &usb_1_ss1_qmpphy_out { |
| remote-endpoint = <&pmic_glink_ss1_ss_in>; |
| }; |
| |
| &usb_2 { |
| status = "okay"; |
| }; |
| |
| &usb_2_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_2_hsphy { |
| vdd-supply = <&vreg_l2e_0p8>; |
| vdda12-supply = <&vreg_l3e_1p2>; |
| |
| phys = <&eusb5_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp { |
| status = "okay"; |
| }; |
| |
| &usb_mp_hsphy0 { |
| vdd-supply = <&vreg_l2e_0p8>; |
| vdda12-supply = <&vreg_l3e_1p2>; |
| |
| phys = <&eusb6_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp_hsphy1 { |
| vdd-supply = <&vreg_l2e_0p8>; |
| vdda12-supply = <&vreg_l3e_1p2>; |
| |
| phys = <&eusb3_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp_qmpphy0 { |
| vdda-phy-supply = <&vreg_l3e_1p2>; |
| vdda-pll-supply = <&vreg_l3c_0p8>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp_qmpphy1 { |
| vdda-phy-supply = <&vreg_l3e_1p2>; |
| vdda-pll-supply = <&vreg_l3c_0p8>; |
| |
| status = "okay"; |
| }; |
