| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| |
| #include "x1e80100.dtsi" |
| #include "x1e80100-pmics.dtsi" |
| |
| / { |
| aliases { |
| serial0 = &uart2; |
| i2c0 = &i2c0; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| i2c5 = &i2c5; |
| i2c7 = &i2c7; |
| }; |
| |
| wcd938x: audio-codec { |
| compatible = "qcom,wcd9385-codec"; |
| |
| reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| |
| vdd-buck-supply = <&vreg_l15b>; |
| vdd-rxtx-supply = <&vreg_l15b>; |
| vdd-io-supply = <&vreg_l15b>; |
| vdd-mic-bias-supply = <&vreg_bob1>; |
| |
| pinctrl-0 = <&wcd_default>; |
| pinctrl-names = "default"; |
| |
| #sound-dai-cells = <1>; |
| }; |
| |
| backlight: backlight { |
| compatible = "pwm-backlight"; |
| pwms = <&pmk8550_pwm 0 5000000>; |
| enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>; |
| /* TODO: power-supply? */ |
| |
| pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>; |
| pinctrl-names = "default"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&hall_int_n_default>; |
| pinctrl-names = "default"; |
| |
| switch-lid { |
| gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| wakeup-source; |
| wakeup-event-action = <EV_ACT_DEASSERTED>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cam_indicator_en>; |
| |
| led-camera-indicator { |
| label = "white:camera-indicator"; |
| function = LED_FUNCTION_INDICATOR; |
| color = <LED_COLOR_ID_WHITE>; |
| gpios = <&tlmm 225 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "none"; |
| default-state = "off"; |
| /* Reuse as a panic indicator until we get a "camera on" trigger */ |
| panic-indicator; |
| }; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,x1e80100-pmic-glink", |
| "qcom,sm8550-pmic-glink", |
| "qcom,pmic-glink"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, |
| <&tlmm 123 GPIO_ACTIVE_HIGH>; |
| |
| /* Left-side rear port */ |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss0_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss0_ss_in: endpoint { |
| remote-endpoint = <&retimer_ss0_ss_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_ss0_con_sbu_in: endpoint { |
| remote-endpoint = <&retimer_ss0_con_sbu_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| /* Left-side front port */ |
| connector@1 { |
| compatible = "usb-c-connector"; |
| reg = <1>; |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_ss1_hs_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss1_ss_in: endpoint { |
| remote-endpoint = <&retimer_ss1_ss_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_ss1_con_sbu_in: endpoint { |
| remote-endpoint = <&retimer_ss1_con_sbu_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| linux,cma { |
| compatible = "shared-dma-pool"; |
| size = <0x0 0x8000000>; |
| reusable; |
| linux,cma-default; |
| }; |
| }; |
| |
| vreg_edp_3p3: regulator-edp-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_EDP_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&edp_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_rtmr0_1p15: regulator-rtmr0-1p15 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_RTMR0_1P15"; |
| |
| regulator-min-microvolt = <1150000>; |
| regulator-max-microvolt = <1150000>; |
| |
| gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&rtmr0_1p15_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_rtmr0_1p8: regulator-rtmr0-1p8 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_RTMR0_1P8"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&rtmr0_1p8_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_rtmr0_3p3: regulator-rtmr0-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_RTMR0_3P3"; |
| |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&rtmr0_3p3_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_rtmr1_1p15: regulator-rtmr1-1p15 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_RTMR1_1P15"; |
| |
| regulator-min-microvolt = <1150000>; |
| regulator-max-microvolt = <1150000>; |
| |
| gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&rtmr1_1p15_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_rtmr1_1p8: regulator-rtmr1-1p8 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_RTMR1_1P8"; |
| |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&rtmr1_1p8_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vreg_rtmr1_3p3: regulator-rtmr1-3p3 { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_RTMR1_3P3"; |
| |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&rtmr1_3p3_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| |
| vreg_nvme: regulator-nvme { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "VREG_NVME_3P3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-0 = <&nvme_reg_en>; |
| pinctrl-names = "default"; |
| |
| regulator-boot-on; |
| }; |
| |
| vph_pwr: regulator-vph-pwr { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| sound { |
| compatible = "qcom,x1e80100-sndcard"; |
| model = "X1E80100-Romulus"; |
| audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC2", "MIC BIAS2", |
| "VA DMIC0", "MIC BIAS3", |
| "VA DMIC1", "MIC BIAS3", |
| "VA DMIC0", "VA MIC BIAS3", |
| "VA DMIC1", "VA MIC BIAS3", |
| "TX SWR_INPUT1", "ADC2_OUTPUT"; |
| |
| va-dai-link { |
| link-name = "VA Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&lpass_vamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, |
| <&swr0 0>, <&lpass_wsamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8550-rpmh-regulators"; |
| qcom,pmic-id = "b"; |
| |
| vdd-bob1-supply = <&vph_pwr>; |
| vdd-bob2-supply = <&vph_pwr>; |
| vdd-l1-l4-l10-supply = <&vreg_s4c>; |
| vdd-l2-l13-l14-supply = <&vreg_bob1>; |
| vdd-l5-l16-supply = <&vreg_bob1>; |
| vdd-l6-l7-supply = <&vreg_bob2>; |
| vdd-l8-l9-supply = <&vreg_bob1>; |
| vdd-l12-supply = <&vreg_s5j>; |
| vdd-l15-supply = <&vreg_s4c>; |
| vdd-l17-supply = <&vreg_bob2>; |
| |
| vreg_bob1: bob1 { |
| regulator-name = "vreg_bob1"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob2: bob2 { |
| regulator-name = "vreg_bob2"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1b: ldo1 { |
| regulator-name = "vreg_l1b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b: ldo2 { |
| regulator-name = "vreg_l2b"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4b: ldo4 { |
| regulator-name = "vreg_l4b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5b: ldo5 { |
| regulator-name = "vreg_l5b"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b: ldo6 { |
| regulator-name = "vreg_l6b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b: ldo7 { |
| regulator-name = "vreg_l7b"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8b: ldo8 { |
| regulator-name = "vreg_l8b"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l9b: ldo9 { |
| regulator-name = "vreg_l9b"; |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l10b: ldo10 { |
| regulator-name = "vreg_l10b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12b: ldo12 { |
| regulator-name = "vreg_l12b"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l13b: ldo13 { |
| regulator-name = "vreg_l13b"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b: ldo14 { |
| regulator-name = "vreg_l14b"; |
| regulator-min-microvolt = <3072000>; |
| regulator-max-microvolt = <3072000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b: ldo15 { |
| regulator-name = "vreg_l15b"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-always-on; |
| }; |
| |
| vreg_l16b: ldo16 { |
| regulator-name = "vreg_l16b"; |
| regulator-min-microvolt = <2912000>; |
| regulator-max-microvolt = <2912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17b: ldo17 { |
| regulator-name = "vreg_l17b"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <2504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "c"; |
| |
| vdd-l1-supply = <&vreg_s5j>; |
| vdd-l2-supply = <&vreg_s1f>; |
| vdd-l3-supply = <&vreg_s1f>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| vreg_s4c: smps4 { |
| regulator-name = "vreg_s4c"; |
| regulator-min-microvolt = <1856000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1c: ldo1 { |
| regulator-name = "vreg_l1c"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2c: ldo2 { |
| regulator-name = "vreg_l2c"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c: ldo3 { |
| regulator-name = "vreg_l3c"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "d"; |
| |
| vdd-l1-supply = <&vreg_s1f>; |
| vdd-l2-supply = <&vreg_s1f>; |
| vdd-l3-supply = <&vreg_s4c>; |
| vdd-s1-supply = <&vph_pwr>; |
| |
| vreg_l1d: ldo1 { |
| regulator-name = "vreg_l1d"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2d: ldo2 { |
| regulator-name = "vreg_l2d"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3d: ldo3 { |
| regulator-name = "vreg_l3d"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-3 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "e"; |
| |
| vdd-l2-supply = <&vreg_s1f>; |
| vdd-l3-supply = <&vreg_s5j>; |
| |
| vreg_l2e: ldo2 { |
| regulator-name = "vreg_l2e"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3e: ldo3 { |
| regulator-name = "vreg_l3e"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-4 { |
| compatible = "qcom,pmc8380-rpmh-regulators"; |
| qcom,pmic-id = "f"; |
| |
| vdd-l1-supply = <&vreg_s5j>; |
| vdd-l2-supply = <&vreg_s5j>; |
| vdd-l3-supply = <&vreg_s5j>; |
| vdd-s1-supply = <&vph_pwr>; |
| |
| vreg_s1f: smps1 { |
| regulator-name = "vreg_s1f"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1f: ldo1 { |
| regulator-name = "vreg_l1f"; |
| regulator-min-microvolt = <1024000>; |
| regulator-max-microvolt = <1024000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2f: ldo2 { |
| regulator-name = "vreg_l2f"; |
| regulator-min-microvolt = <1024000>; |
| regulator-max-microvolt = <1024000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3f: ldo3 { |
| regulator-name = "vreg_l3f"; |
| regulator-min-microvolt = <1024000>; |
| regulator-max-microvolt = <1024000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-6 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "i"; |
| |
| vdd-l1-supply = <&vreg_s4c>; |
| vdd-l2-supply = <&vreg_s5j>; |
| vdd-l3-supply = <&vreg_s1f>; |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| |
| vreg_s1i: smps1 { |
| regulator-name = "vreg_s1i"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s2i: smps2 { |
| regulator-name = "vreg_s2i"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1i: ldo1 { |
| regulator-name = "vreg_l1i"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2i: ldo2 { |
| regulator-name = "vreg_l2i"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3i: ldo3 { |
| regulator-name = "vreg_l3i"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-7 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| qcom,pmic-id = "j"; |
| |
| vdd-l1-supply = <&vreg_s1f>; |
| vdd-l2-supply = <&vreg_s5j>; |
| vdd-l3-supply = <&vreg_s1f>; |
| vdd-s5-supply = <&vph_pwr>; |
| |
| vreg_s5j: smps5 { |
| regulator-name = "vreg_s5j"; |
| regulator-min-microvolt = <1256000>; |
| regulator-max-microvolt = <1304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1j: ldo1 { |
| regulator-name = "vreg_l1j"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2j: ldo2 { |
| regulator-name = "vreg_l2j"; |
| regulator-min-microvolt = <1256000>; |
| regulator-max-microvolt = <1256000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3j: ldo3 { |
| regulator-name = "vreg_l3j"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| memory-region = <&gpu_microcode_mem>; |
| firmware-name = "qcom/x1e80100/microsoft/qcdxkmsuc8380.mbn"; |
| }; |
| }; |
| |
| &i2c0 { |
| clock-frequency = <100000>; |
| |
| status = "okay"; |
| |
| /* Something @39, @3e, @44 */ |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| /* Left-side rear port */ |
| typec-mux@8 { |
| compatible = "parade,ps8830"; |
| reg = <0x8>; |
| |
| reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>; |
| |
| clocks = <&rpmhcc RPMH_RF_CLK3>; |
| |
| vdd-supply = <&vreg_rtmr0_1p15>; |
| vdd33-supply = <&vreg_rtmr0_3p3>; |
| vdd33-cap-supply = <&vreg_rtmr0_3p3>; |
| vddar-supply = <&vreg_rtmr0_1p15>; |
| vddat-supply = <&vreg_rtmr0_1p15>; |
| vddio-supply = <&vreg_rtmr0_1p8>; |
| |
| pinctrl-0 = <&rtmr0_default>; |
| pinctrl-names = "default"; |
| |
| retimer-switch; |
| orientation-switch; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| retimer_ss0_ss_out: endpoint { |
| remote-endpoint = <&pmic_glink_ss0_ss_in>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| retimer_ss0_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss0_qmpphy_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| retimer_ss0_con_sbu_out: endpoint { |
| remote-endpoint = <&pmic_glink_ss0_con_sbu_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| }; |
| |
| &i2c4 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| /* Something @18, @2c, @2e */ |
| }; |
| |
| &i2c5 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| ptn3222: redriver@4f { |
| compatible = "nxp,ptn3222"; |
| reg = <0x4f>; |
| |
| reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>; |
| |
| vdd3v3-supply = <&vreg_l13b>; |
| vdd1v8-supply = <&vreg_l4b>; |
| |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| &i2c7 { |
| clock-frequency = <400000>; |
| |
| status = "okay"; |
| |
| /* Left-side front port */ |
| typec-mux@8 { |
| compatible = "parade,ps8830"; |
| reg = <0x8>; |
| |
| reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>; |
| |
| clocks = <&rpmhcc RPMH_RF_CLK4>; |
| |
| vdd-supply = <&vreg_rtmr1_1p15>; |
| vdd33-supply = <&vreg_rtmr1_3p3>; |
| vdd33-cap-supply = <&vreg_rtmr1_3p3>; |
| vddar-supply = <&vreg_rtmr1_1p15>; |
| vddat-supply = <&vreg_rtmr1_1p15>; |
| vddio-supply = <&vreg_rtmr1_1p8>; |
| |
| retimer-switch; |
| orientation-switch; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| retimer_ss1_ss_out: endpoint { |
| remote-endpoint = <&pmic_glink_ss1_ss_in>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| retimer_ss1_ss_in: endpoint { |
| remote-endpoint = <&usb_1_ss1_qmpphy_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| retimer_ss1_con_sbu_out: endpoint { |
| remote-endpoint = <&pmic_glink_ss1_con_sbu_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &lpass_tlmm { |
| spkr_01_sd_n_active: spkr-01-sd-n-active-state { |
| pins = "gpio12"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &lpass_vamacro { |
| qcom,dmic-sample-rate = <4800000>; |
| |
| vdd-micb-supply = <&vreg_l1b>; |
| |
| pinctrl-0 = <&dmic01_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dp0 { |
| status = "okay"; |
| }; |
| |
| &mdss_dp0_out { |
| data-lanes = <0 1>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| }; |
| |
| &mdss_dp1 { |
| status = "okay"; |
| }; |
| |
| &mdss_dp1_out { |
| data-lanes = <0 1>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| }; |
| |
| &mdss_dp3 { |
| /delete-property/ #sound-dai-cells; |
| |
| status = "okay"; |
| |
| aux-bus { |
| panel { |
| compatible = "edp-panel"; |
| |
| backlight = <&backlight>; |
| power-supply = <&vreg_edp_3p3>; |
| |
| port { |
| edp_panel_in: endpoint { |
| remote-endpoint = <&mdss_dp3_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| |
| mdss_dp3_out: endpoint { |
| data-lanes = <0 1 2 3>; |
| link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| |
| remote-endpoint = <&edp_panel_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dp3_phy { |
| vdda-phy-supply = <&vreg_l3j>; |
| vdda-pll-supply = <&vreg_l2j>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie3 { |
| perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&pcie3_default>; |
| pinctrl-names = "default"; |
| |
| /* The RTS5261 chip on the other side only does Gen1x1 anyway */ |
| max-link-speed = <1>; |
| status = "okay"; |
| }; |
| |
| &pcie3_phy { |
| vdda-phy-supply = <&vreg_l3c>; |
| vdda-pll-supply = <&vreg_l3e>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie4 { |
| status = "okay"; |
| }; |
| |
| &pcie4_phy { |
| vdda-phy-supply = <&vreg_l3i>; |
| vdda-pll-supply = <&vreg_l3e>; |
| |
| status = "okay"; |
| }; |
| |
| &pcie6a { |
| perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; |
| wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; |
| |
| vddpe-3v3-supply = <&vreg_nvme>; |
| |
| pinctrl-0 = <&pcie6a_default>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &pcie6a_phy { |
| vdda-phy-supply = <&vreg_l1d>; |
| vdda-pll-supply = <&vreg_l2j>; |
| |
| status = "okay"; |
| }; |
| |
| &pm8550_gpios { |
| rtmr0_default: rtmr0-reset-n-active-state { |
| pins = "gpio10"; |
| function = "normal"; |
| power-source = <1>; /* 1.8V */ |
| }; |
| |
| rtmr0_3p3_reg_en: rtmr0-3p3-reg-en-state { |
| pins = "gpio11"; |
| function = "normal"; |
| power-source = <1>; /* 1.8V */ |
| }; |
| }; |
| |
| &pm8550ve_9_gpios { |
| rtmr0_1p8_reg_en: rtmr0-1p8-reg-en-state { |
| pins = "gpio8"; |
| function = "normal"; |
| power-source = <1>; /* 1.8V */ |
| }; |
| }; |
| |
| &pmc8380_3_gpios { |
| edp_bl_en: edp-bl-en-state { |
| pins = "gpio4"; |
| function = "normal"; |
| power-source = <1>; /* 1.8V */ |
| input-disable; |
| output-enable; |
| }; |
| }; |
| |
| &pmc8380_5_gpios { |
| rtmr0_1p15_reg_en: rtmr0-1p15-reg-en-state { |
| pins = "gpio8"; |
| function = "normal"; |
| power-source = <1>; /* 1.8V */ |
| }; |
| }; |
| |
| &pmk8550_pwm { |
| status = "okay"; |
| }; |
| |
| &pmk8550_gpios { |
| edp_bl_pwm: edp-bl-pwm-state { |
| pins = "gpio5"; |
| function = "func3"; |
| }; |
| }; |
| |
| &qupv3_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_1 { |
| status = "okay"; |
| }; |
| |
| &qupv3_2 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/x1e80100/microsoft/Romulus/qcadsp8380.mbn", |
| "qcom/x1e80100/microsoft/Romulus/adsp_dtbs.elf"; |
| |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/x1e80100/microsoft/Romulus/qccdsp8380.mbn", |
| "qcom/x1e80100/microsoft/Romulus/cdsp_dtbs.elf"; |
| |
| status = "okay"; |
| }; |
| |
| &smb2360_0 { |
| status = "okay"; |
| }; |
| |
| &smb2360_0_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d>; |
| vdd3-supply = <&vreg_l2b>; |
| }; |
| |
| &smb2360_1 { |
| status = "okay"; |
| }; |
| |
| &smb2360_1_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d>; |
| vdd3-supply = <&vreg_l14b>; |
| }; |
| |
| &smb2360_2 { |
| status = "okay"; |
| }; |
| |
| &smb2360_2_eusb2_repeater { |
| vdd18-supply = <&vreg_l3d>; |
| vdd3-supply = <&vreg_l8b>; |
| }; |
| |
| &swr0 { |
| pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| |
| /* WSA8845, Left speaker */ |
| left_spkr: speaker@0,0 { |
| compatible = "sdw20217020400"; |
| reg = <0 0>; |
| reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| vdd-1p8-supply = <&vreg_l15b>; |
| vdd-io-supply = <&vreg_l12b>; |
| qcom,port-mapping = <1 2 3 7 10 13>; |
| }; |
| |
| /* WSA8845, Right speaker */ |
| right_spkr: speaker@0,1 { |
| compatible = "sdw20217020400"; |
| reg = <0 1>; |
| reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| vdd-1p8-supply = <&vreg_l15b>; |
| vdd-io-supply = <&vreg_l12b>; |
| qcom,port-mapping = <4 5 6 7 11 13>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| /* WCD9385 RX */ |
| wcd_rx: codec@0,4 { |
| compatible = "sdw20217010d00"; |
| reg = <0 4>; |
| qcom,rx-port-mapping = <1 2 3 4 5>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| /* WCD9385 TX */ |
| wcd_tx: codec@0,3 { |
| compatible = "sdw20217010d00"; |
| reg = <0 3>; |
| qcom,tx-port-mapping = <2 2 3 4>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <44 4>, /* SPI (TPM) */ |
| <238 1>; /* UFS Reset */ |
| |
| hall_int_n_default: hall-int-n-state { |
| pins = "gpio2"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| nvme_reg_en: nvme-reg-en-state { |
| pins = "gpio18"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| edp_reg_en: edp-reg-en-state { |
| pins = "gpio70"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| ssam_state: ssam-state-state { |
| pins = "gpio91"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| pcie3_default: pcie3-default-state { |
| perst-n-pins { |
| pins = "gpio143"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| clkreq-n-pins { |
| pins = "gpio144"; |
| function = "pcie3_clk"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio145"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| pcie6a_default: pcie6a-default-state { |
| perst-n-pins { |
| pins = "gpio152"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| clkreq-n-pins { |
| pins = "gpio153"; |
| function = "pcie6a_clk"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| wake-n-pins { |
| pins = "gpio154"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| rtmr1_1p8_reg_en: rtmr1-1p8-reg-en-state { |
| pins = "gpio175"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rtmr1_3p3_reg_en: rtmr1-3p3-reg-en-state { |
| pins = "gpio186"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| rtmr1_1p15_reg_en: rtmr1-1p15-reg-en-state { |
| pins = "gpio188"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wcd_default: wcd-reset-n-active-state { |
| pins = "gpio191"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| cam_indicator_en: cam-indicator-en-state { |
| pins = "gpio225"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| &uart2 { |
| status = "okay"; |
| |
| embedded-controller { |
| compatible = "microsoft,surface-sam"; |
| |
| interrupts-extended = <&tlmm 91 IRQ_TYPE_EDGE_RISING>; |
| |
| current-speed = <4000000>; |
| |
| pinctrl-0 = <&ssam_state>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &usb_1_ss0_hsphy { |
| vdd-supply = <&vreg_l3j>; |
| vdda12-supply = <&vreg_l2j>; |
| |
| phys = <&smb2360_0_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_qmpphy { |
| vdda-phy-supply = <&vreg_l2j>; |
| vdda-pll-supply = <&vreg_l1j>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss0_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss0_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss0_hs_in>; |
| }; |
| |
| &usb_1_ss0_qmpphy_out { |
| remote-endpoint = <&retimer_ss0_ss_in>; |
| }; |
| |
| &usb_1_ss1_hsphy { |
| vdd-supply = <&vreg_l3j>; |
| vdda12-supply = <&vreg_l2j>; |
| |
| phys = <&smb2360_1_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1_qmpphy { |
| vdda-phy-supply = <&vreg_l2j>; |
| vdda-pll-supply = <&vreg_l2d>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_ss1_dwc3 { |
| dr_mode = "host"; |
| }; |
| |
| &usb_1_ss1_dwc3_hs { |
| remote-endpoint = <&pmic_glink_ss1_hs_in>; |
| }; |
| |
| &usb_1_ss1_qmpphy_out { |
| remote-endpoint = <&retimer_ss1_ss_in>; |
| }; |
| |
| /* MP0 goes to the Surface Connector, MP1 goes to the USB-A port */ |
| &usb_mp { |
| status = "okay"; |
| }; |
| |
| &usb_mp_hsphy0 { |
| vdd-supply = <&vreg_l2e>; |
| vdda12-supply = <&vreg_l2j>; |
| |
| phys = <&smb2360_2_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp_hsphy1 { |
| vdd-supply = <&vreg_l2e>; |
| vdda12-supply = <&vreg_l2j>; |
| |
| phys = <&ptn3222>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp_qmpphy0 { |
| vdda-phy-supply = <&vreg_l3e>; |
| vdda-pll-supply = <&vreg_l3c>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_mp_qmpphy1 { |
| vdda-phy-supply = <&vreg_l3e>; |
| vdda-pll-supply = <&vreg_l3c>; |
| |
| status = "okay"; |
| }; |
