| # SPDX-License-Identifier: GPL-2.0 |
| # |
| # For a description of the syntax of this configuration file, |
| # see Documentation/kbuild/kconfig-language.rst. |
| # |
| # Auxiliary display drivers configuration. |
| # |
| |
| menuconfig AUXDISPLAY |
| bool "Auxiliary Display support" |
| help |
| Say Y here to get to see options for auxiliary display drivers. |
| This option alone does not add any kernel code. |
| |
| If you say N, all options in this submenu will be skipped and disabled. |
| |
| if AUXDISPLAY |
| |
| config CHARLCD |
| tristate "Character LCD core support" if COMPILE_TEST |
| help |
| This is the base system for character-based LCD displays. |
| It makes no sense to have this alone, you select your display driver |
| and if it needs the charlcd core, it will select it automatically. |
| This is some character LCD core interface that multiple drivers can |
| use. |
| |
| config LINEDISP |
| tristate "Character line display core support" if COMPILE_TEST |
| help |
| This is the core support for single-line character displays, to be |
| selected by drivers that use it. |
| |
| config HD44780_COMMON |
| tristate "Common functions for HD44780 (and compatibles) LCD displays" if COMPILE_TEST |
| select CHARLCD |
| help |
| This is a module with the common symbols for HD44780 (and compatibles) |
| displays. This is the code that multiple other modules use. It is not |
| useful alone. If you have some sort of HD44780 compatible display, |
| you very likely use this. It is selected automatically by selecting |
| your concrete display. |
| |
| config HD44780 |
| tristate "HD44780 Character LCD support" |
| depends on GPIOLIB || COMPILE_TEST |
| select HD44780_COMMON |
| help |
| Enable support for Character LCDs using a HD44780 controller. |
| The LCD is accessible through the /dev/lcd char device (10, 156). |
| This code can either be compiled as a module, or linked into the |
| kernel and started at boot. |
| If you don't understand what all this is about, say N. |
| |
| config KS0108 |
| tristate "KS0108 LCD Controller" |
| depends on PARPORT_PC |
| default n |
| help |
| If you have a LCD controlled by one or more KS0108 |
| controllers, say Y. You will need also another more specific |
| driver for your LCD. |
| |
| Depends on Parallel Port support. If you say Y at |
| parport, you will be able to compile this as a module (M) |
| and built-in as well (Y). |
| |
| To compile this as a module, choose M here: |
| the module will be called ks0108. |
| |
| If unsure, say N. |
| |
| config KS0108_PORT |
| hex "Parallel port where the LCD is connected" |
| depends on KS0108 |
| default 0x378 |
| help |
| The address of the parallel port where the LCD is connected. |
| |
| The first standard parallel port address is 0x378. |
| The second standard parallel port address is 0x278. |
| The third standard parallel port address is 0x3BC. |
| |
| You can specify a different address if you need. |
| |
| If you don't know what I'm talking about, load the parport module, |
| and execute "dmesg" or "cat /proc/ioports". You can see there how |
| many parallel ports are present and which address each one has. |
| |
| Usually you only need to use 0x378. |
| |
| If you compile this as a module, you can still override this |
| using the module parameters. |
| |
| config KS0108_DELAY |
| int "Delay between each control writing (microseconds)" |
| depends on KS0108 |
| default "2" |
| help |
| Amount of time the ks0108 should wait between each control write |
| to the parallel port. |
| |
| If your LCD seems to miss random writings, increment this. |
| |
| If you don't know what I'm talking about, ignore it. |
| |
| If you compile this as a module, you can still override this |
| value using the module parameters. |
| |
| config CFAG12864B |
| tristate "CFAG12864B LCD" |
| depends on X86 |
| depends on FB |
| depends on KS0108 |
| select FB_SYS_FILLRECT |
| select FB_SYS_COPYAREA |
| select FB_SYS_IMAGEBLIT |
| select FB_SYS_FOPS |
| default n |
| help |
| If you have a Crystalfontz 128x64 2-color LCD, cfag12864b Series, |
| say Y. You also need the ks0108 LCD Controller driver. |
| |
| For help about how to wire your LCD to the parallel port, |
| check Documentation/admin-guide/auxdisplay/cfag12864b.rst |
| |
| Depends on the x86 arch and the framebuffer support. |
| |
| The LCD framebuffer driver can be attached to a console. |
| It will work fine. However, you can't attach it to the fbdev driver |
| of the xorg server. |
| |
| To compile this as a module, choose M here: |
| the modules will be called cfag12864b and cfag12864bfb. |
| |
| If unsure, say N. |
| |
| config CFAG12864B_RATE |
| int "Refresh rate (hertz)" |
| depends on CFAG12864B |
| default "20" |
| help |
| Refresh rate of the LCD. |
| |
| As the LCD is not memory mapped, the driver has to make the work by |
| software. This means you should be careful setting this value higher. |
| If your CPUs are really slow or you feel the system is slowed down, |
| decrease the value. |
| |
| Be careful modifying this value to a very high value: |
| You can freeze the computer, or the LCD maybe can't draw as fast as you |
| are requesting. |
| |
| If you don't know what I'm talking about, ignore it. |
| |
| If you compile this as a module, you can still override this |
| value using the module parameters. |
| |
| config IMG_ASCII_LCD |
| tristate "Imagination Technologies ASCII LCD Display" |
| depends on HAS_IOMEM |
| default y if MIPS_MALTA |
| select MFD_SYSCON |
| select LINEDISP |
| help |
| Enable this to support the simple ASCII LCD displays found on |
| development boards such as the MIPS Boston, MIPS Malta & MIPS SEAD3 |
| from Imagination Technologies. |
| |
| config HT16K33 |
| tristate "Holtek Ht16K33 LED controller with keyscan" |
| depends on FB && I2C && INPUT |
| select FB_SYS_FOPS |
| select FB_SYS_FILLRECT |
| select FB_SYS_COPYAREA |
| select FB_SYS_IMAGEBLIT |
| select INPUT_MATRIXKMAP |
| select FB_BACKLIGHT |
| select NEW_LEDS |
| select LEDS_CLASS |
| select LINEDISP |
| help |
| Say yes here to add support for Holtek HT16K33, RAM mapping 16*8 |
| LED controller driver with keyscan. |
| |
| config LCD2S |
| tristate "lcd2s 20x4 character display over I2C console" |
| depends on I2C |
| select CHARLCD |
| help |
| This is a driver that lets you use the lcd2s 20x4 character display |
| from Modtronix engineering as a console output device. The display |
| is a simple single color character display. You have to connect it |
| to an I2C bus. |
| |
| config ARM_CHARLCD |
| bool "ARM Ltd. Character LCD Driver" |
| depends on PLAT_VERSATILE |
| help |
| This is a driver for the character LCD found on the ARM Ltd. |
| Versatile and RealView Platform Baseboards. It doesn't do |
| very much more than display the text "ARM Linux" on the first |
| line and the Linux version on the second line, but that's |
| still useful. |
| |
| menuconfig PARPORT_PANEL |
| tristate "Parallel port LCD/Keypad Panel support" |
| depends on PARPORT |
| select HD44780_COMMON |
| help |
| Say Y here if you have an HD44780 or KS-0074 LCD connected to your |
| parallel port. This driver also features 4 and 6-key keypads. The LCD |
| is accessible through the /dev/lcd char device (10, 156), and the |
| keypad through /dev/keypad (10, 185). This code can either be |
| compiled as a module, or linked into the kernel and started at boot. |
| If you don't understand what all this is about, say N. |
| |
| if PARPORT_PANEL |
| |
| config PANEL_PARPORT |
| int "Default parallel port number (0=LPT1)" |
| range 0 255 |
| default "0" |
| help |
| This is the index of the parallel port the panel is connected to. One |
| driver instance only supports one parallel port, so if your keypad |
| and LCD are connected to two separate ports, you have to start two |
| modules with different arguments. Numbering starts with '0' for LPT1, |
| and so on. |
| |
| config PANEL_PROFILE |
| int "Default panel profile (0-5, 0=custom)" |
| range 0 5 |
| default "5" |
| help |
| To ease configuration, the driver supports different configuration |
| profiles for past and recent wirings. These profiles can also be |
| used to define an approximative configuration, completed by a few |
| other options. Here are the profiles : |
| |
| 0 = custom (see further) |
| 1 = 2x16 parallel LCD, old keypad |
| 2 = 2x16 serial LCD (KS-0074), new keypad |
| 3 = 2x16 parallel LCD (Hantronix), no keypad |
| 4 = 2x16 parallel LCD (Nexcom NSA1045) with Nexcom's keypad |
| 5 = 2x40 parallel LCD (old one), with old keypad |
| |
| Custom configurations allow you to define how your display is |
| wired to the parallel port, and how it works. This is only intended |
| for experts. |
| |
| config PANEL_KEYPAD |
| depends on PANEL_PROFILE="0" |
| int "Keypad type (0=none, 1=old 6 keys, 2=new 6 keys, 3=Nexcom 4 keys)" |
| range 0 3 |
| default 0 |
| help |
| This enables and configures a keypad connected to the parallel port. |
| The keys will be read from character device 10,185. Valid values are : |
| |
| 0 : do not enable this driver |
| 1 : old 6 keys keypad |
| 2 : new 6 keys keypad, as used on the server at www.ant-computing.com |
| 3 : Nexcom NSA1045's 4 keys keypad |
| |
| New profiles can be described in the driver source. The driver also |
| supports simultaneous keys pressed when the keypad supports them. |
| |
| config PANEL_LCD |
| depends on PANEL_PROFILE="0" |
| int "LCD type (0=none, 1=custom, 2=old //, 3=ks0074, 4=hantronix, 5=Nexcom)" |
| range 0 5 |
| default 0 |
| help |
| This enables and configures an LCD connected to the parallel port. |
| The driver includes an interpreter for escape codes starting with |
| '\e[L' which are specific to the LCD, and a few ANSI codes. The |
| driver will be registered as character device 10,156, usually |
| under the name '/dev/lcd'. There are a total of 6 supported types : |
| |
| 0 : do not enable the driver |
| 1 : custom configuration and wiring (see further) |
| 2 : 2x16 & 2x40 parallel LCD (old wiring) |
| 3 : 2x16 serial LCD (KS-0074 based) |
| 4 : 2x16 parallel LCD (Hantronix wiring) |
| 5 : 2x16 parallel LCD (Nexcom wiring) |
| |
| When type '1' is specified, other options will appear to configure |
| more precise aspects (wiring, dimensions, protocol, ...). Please note |
| that those values changed from the 2.4 driver for better consistency. |
| |
| config PANEL_LCD_HEIGHT |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "Number of lines on the LCD (1-2)" |
| range 1 2 |
| default 2 |
| help |
| This is the number of visible character lines on the LCD in custom profile. |
| It can either be 1 or 2. |
| |
| config PANEL_LCD_WIDTH |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "Number of characters per line on the LCD (1-40)" |
| range 1 40 |
| default 40 |
| help |
| This is the number of characters per line on the LCD in custom profile. |
| Common values are 16,20,24,40. |
| |
| config PANEL_LCD_BWIDTH |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "Internal LCD line width (1-40, 40 by default)" |
| range 1 40 |
| default 40 |
| help |
| Most LCDs use a standard controller which supports hardware lines of 40 |
| characters, although sometimes only 16, 20 or 24 of them are really wired |
| to the terminal. This results in some non-visible but addressable characters, |
| and is the case for most parallel LCDs. Other LCDs, and some serial ones, |
| however, use the same line width internally as what is visible. The KS0074 |
| for example, uses 16 characters per line for 16 visible characters per line. |
| |
| This option lets you configure the value used by your LCD in 'custom' profile. |
| If you don't know, put '40' here. |
| |
| config PANEL_LCD_HWIDTH |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "Hardware LCD line width (1-64, 64 by default)" |
| range 1 64 |
| default 64 |
| help |
| Most LCDs use a single address bit to differentiate line 0 and line 1. Since |
| some of them need to be able to address 40 chars with the lower bits, they |
| often use the immediately superior power of 2, which is 64, to address the |
| next line. |
| |
| If you don't know what your LCD uses, in doubt let 16 here for a 2x16, and |
| 64 here for a 2x40. |
| |
| config PANEL_LCD_CHARSET |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "LCD character set (0=normal, 1=KS0074)" |
| range 0 1 |
| default 0 |
| help |
| Some controllers such as the KS0074 use a somewhat strange character set |
| where many symbols are at unusual places. The driver knows how to map |
| 'standard' ASCII characters to the character sets used by these controllers. |
| Valid values are : |
| |
| 0 : normal (untranslated) character set |
| 1 : KS0074 character set |
| |
| If you don't know, use the normal one (0). |
| |
| config PANEL_LCD_PROTO |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "LCD communication mode (0=parallel 8 bits, 1=serial)" |
| range 0 1 |
| default 0 |
| help |
| This driver now supports any serial or parallel LCD wired to a parallel |
| port. But before assigning signals, the driver needs to know if it will |
| be driving a serial LCD or a parallel one. Serial LCDs only use 2 wires |
| (SDA/SCL), while parallel ones use 2 or 3 wires for the control signals |
| (E, RS, sometimes RW), and 4 or 8 for the data. Use 0 here for a 8 bits |
| parallel LCD, and 1 for a serial LCD. |
| |
| config PANEL_LCD_PIN_E |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0" |
| int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) " |
| range -17 17 |
| default 14 |
| help |
| This describes the number of the parallel port pin to which the LCD 'E' |
| signal has been connected. It can be : |
| |
| 0 : no connection (eg: connected to ground) |
| 1..17 : directly connected to any of these pins on the DB25 plug |
| -1..-17 : connected to the same pin through an inverter (eg: transistor). |
| |
| Default for the 'E' pin in custom profile is '14' (AUTOFEED). |
| |
| config PANEL_LCD_PIN_RS |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0" |
| int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) " |
| range -17 17 |
| default 17 |
| help |
| This describes the number of the parallel port pin to which the LCD 'RS' |
| signal has been connected. It can be : |
| |
| 0 : no connection (eg: connected to ground) |
| 1..17 : directly connected to any of these pins on the DB25 plug |
| -1..-17 : connected to the same pin through an inverter (eg: transistor). |
| |
| Default for the 'RS' pin in custom profile is '17' (SELECT IN). |
| |
| config PANEL_LCD_PIN_RW |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0" |
| int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) " |
| range -17 17 |
| default 16 |
| help |
| This describes the number of the parallel port pin to which the LCD 'RW' |
| signal has been connected. It can be : |
| |
| 0 : no connection (eg: connected to ground) |
| 1..17 : directly connected to any of these pins on the DB25 plug |
| -1..-17 : connected to the same pin through an inverter (eg: transistor). |
| |
| Default for the 'RW' pin in custom profile is '16' (INIT). |
| |
| config PANEL_LCD_PIN_SCL |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0" |
| int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) " |
| range -17 17 |
| default 1 |
| help |
| This describes the number of the parallel port pin to which the serial |
| LCD 'SCL' signal has been connected. It can be : |
| |
| 0 : no connection (eg: connected to ground) |
| 1..17 : directly connected to any of these pins on the DB25 plug |
| -1..-17 : connected to the same pin through an inverter (eg: transistor). |
| |
| Default for the 'SCL' pin in custom profile is '1' (STROBE). |
| |
| config PANEL_LCD_PIN_SDA |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0" |
| int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) " |
| range -17 17 |
| default 2 |
| help |
| This describes the number of the parallel port pin to which the serial |
| LCD 'SDA' signal has been connected. It can be : |
| |
| 0 : no connection (eg: connected to ground) |
| 1..17 : directly connected to any of these pins on the DB25 plug |
| -1..-17 : connected to the same pin through an inverter (eg: transistor). |
| |
| Default for the 'SDA' pin in custom profile is '2' (D0). |
| |
| config PANEL_LCD_PIN_BL |
| depends on PANEL_PROFILE="0" && PANEL_LCD="1" |
| int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) " |
| range -17 17 |
| default 0 |
| help |
| This describes the number of the parallel port pin to which the LCD 'BL' signal |
| has been connected. It can be : |
| |
| 0 : no connection (eg: connected to ground) |
| 1..17 : directly connected to any of these pins on the DB25 plug |
| -1..-17 : connected to the same pin through an inverter (eg: transistor). |
| |
| Default for the 'BL' pin in custom profile is '0' (uncontrolled). |
| |
| endif # PARPORT_PANEL |
| |
| config PANEL_CHANGE_MESSAGE |
| bool "Change LCD initialization message ?" |
| depends on CHARLCD |
| default "n" |
| help |
| This allows you to replace the boot message indicating the kernel version |
| and the driver version with a custom message. This is useful on appliances |
| where a simple 'Starting system' message can be enough to stop a customer |
| from worrying. |
| |
| If you say 'Y' here, you'll be able to choose a message yourself. Otherwise, |
| say 'N' and keep the default message with the version. |
| |
| config PANEL_BOOT_MESSAGE |
| depends on PANEL_CHANGE_MESSAGE="y" |
| string "New initialization message" |
| default "" |
| help |
| This allows you to replace the boot message indicating the kernel version |
| and the driver version with a custom message. This is useful on appliances |
| where a simple 'Starting system' message can be enough to stop a customer |
| from worrying. |
| |
| An empty message will only clear the display at driver init time. Any other |
| printf()-formatted message is valid with newline and escape codes. |
| |
| choice |
| prompt "Backlight initial state" |
| default CHARLCD_BL_FLASH |
| help |
| Select the initial backlight state on boot or module load. |
| |
| Previously, there was no option for this: the backlight flashed |
| briefly on init. Now you can also turn it off/on. |
| |
| config CHARLCD_BL_OFF |
| bool "Off" |
| help |
| Backlight is initially turned off |
| |
| config CHARLCD_BL_ON |
| bool "On" |
| help |
| Backlight is initially turned on |
| |
| config CHARLCD_BL_FLASH |
| bool "Flash" |
| help |
| Backlight is flashed briefly on init |
| |
| endchoice |
| |
| endif # AUXDISPLAY |
| |
| config PANEL |
| tristate "Parallel port LCD/Keypad Panel support (OLD OPTION)" |
| depends on PARPORT |
| select AUXDISPLAY |
| select PARPORT_PANEL |
