| Kernel driver bel-pfe |
| ====================== |
| |
| Supported chips: |
| |
| * BEL PFE1100 |
| |
| Prefixes: 'pfe1100' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe1100-12-054xa.pdf |
| |
| * BEL PFE3000 |
| |
| Prefixes: 'pfe3000' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-pfe3000-series.pdf |
| |
| Author: Tao Ren <rentao.bupt@gmail.com> |
| |
| |
| Description |
| ----------- |
| |
| This driver supports hardware monitoring for below power supply devices |
| which support PMBus Protocol: |
| |
| * BEL PFE1100 |
| |
| 1100 Watt AC to DC power-factor-corrected (PFC) power supply. |
| PMBus Communication Manual is not publicly available. |
| |
| * BEL PFE3000 |
| |
| 3000 Watt AC/DC power-factor-corrected (PFC) and DC-DC power supply. |
| PMBus Communication Manual is not publicly available. |
| |
| The driver is a client driver to the core PMBus driver. Please see |
| Documentation/hwmon/pmbus.rst for details on PMBus client drivers. |
| |
| |
| Usage Notes |
| ----------- |
| |
| This driver does not auto-detect devices. You will have to instantiate the |
| devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for |
| details. |
| |
| Example: the following will load the driver for an PFE3000 at address 0x20 |
| on I2C bus #1:: |
| |
| $ modprobe bel-pfe |
| $ echo pfe3000 0x20 > /sys/bus/i2c/devices/i2c-1/new_device |
| |
| |
| Platform data support |
| --------------------- |
| |
| The driver supports standard PMBus driver platform data. |
| |
| |
| Sysfs entries |
| ------------- |
| |
| ======================= ======================================================= |
| curr1_label "iin" |
| curr1_input Measured input current |
| curr1_max Input current max value |
| curr1_max_alarm Input current max alarm |
| |
| curr[2-3]_label "iout[1-2]" |
| curr[2-3]_input Measured output current |
| curr[2-3]_max Output current max value |
| curr[2-3]_max_alarm Output current max alarm |
| |
| fan[1-2]_input Fan 1 and 2 speed in RPM |
| fan1_target Set fan speed reference for both fans |
| |
| in1_label "vin" |
| in1_input Measured input voltage |
| in1_crit Input voltage critical max value |
| in1_crit_alarm Input voltage critical max alarm |
| in1_lcrit Input voltage critical min value |
| in1_lcrit_alarm Input voltage critical min alarm |
| in1_max Input voltage max value |
| in1_max_alarm Input voltage max alarm |
| |
| in2_label "vcap" |
| in2_input Hold up capacitor voltage |
| |
| in[3-8]_label "vout[1-3,5-7]" |
| in[3-8]_input Measured output voltage |
| in[3-4]_alarm vout[1-2] output voltage alarm |
| |
| power[1-2]_label "pin[1-2]" |
| power[1-2]_input Measured input power |
| power[1-2]_alarm Input power high alarm |
| |
| power[3-4]_label "pout[1-2]" |
| power[3-4]_input Measured output power |
| |
| temp[1-3]_input Measured temperature |
| temp[1-3]_alarm Temperature alarm |
| ======================= ======================================================= |
| |
| .. note:: |
| |
| - curr3, fan2, vout[2-7], vcap, pin2, pout2 and temp3 attributes only |
| exist for PFE3000. |
