| #!/bin/sh | |
| # SPDX-License-Identifier: GPL-2.0 | |
| # | |
| # Test for mishandling of splice() on pseudofilesystems, which should catch | |
| # bugs like 11990a5bd7e5 ("module: Correctly truncate sysfs sections output") | |
| # | |
| # Since splice fallback was removed as part of the set_fs() rework, many of these | |
| # tests expect to fail now. See https://lore.kernel.org/lkml/202009181443.C2179FB@keescook/ | |
| set -e | |
| DIR=$(dirname "$0") | |
| ret=0 | |
| expect_success() | |
| { | |
| title="$1" | |
| shift | |
| echo "" >&2 | |
| echo "$title ..." >&2 | |
| set +e | |
| "$@" | |
| rc=$? | |
| set -e | |
| case "$rc" in | |
| 0) | |
| echo "ok: $title succeeded" >&2 | |
| ;; | |
| 1) | |
| echo "FAIL: $title should work" >&2 | |
| ret=$(( ret + 1 )) | |
| ;; | |
| *) | |
| echo "FAIL: something else went wrong" >&2 | |
| ret=$(( ret + 1 )) | |
| ;; | |
| esac | |
| } | |
| expect_failure() | |
| { | |
| title="$1" | |
| shift | |
| echo "" >&2 | |
| echo "$title ..." >&2 | |
| set +e | |
| "$@" | |
| rc=$? | |
| set -e | |
| case "$rc" in | |
| 0) | |
| echo "FAIL: $title unexpectedly worked" >&2 | |
| ret=$(( ret + 1 )) | |
| ;; | |
| 1) | |
| echo "ok: $title correctly failed" >&2 | |
| ;; | |
| *) | |
| echo "FAIL: something else went wrong" >&2 | |
| ret=$(( ret + 1 )) | |
| ;; | |
| esac | |
| } | |
| do_splice() | |
| { | |
| filename="$1" | |
| bytes="$2" | |
| expected="$3" | |
| report="$4" | |
| out=$("$DIR"/splice_read "$filename" "$bytes" | cat) | |
| if [ "$out" = "$expected" ] ; then | |
| echo " matched $report" >&2 | |
| return 0 | |
| else | |
| echo " no match: '$out' vs $report" >&2 | |
| return 1 | |
| fi | |
| } | |
| test_splice() | |
| { | |
| filename="$1" | |
| echo " checking $filename ..." >&2 | |
| full=$(cat "$filename") | |
| rc=$? | |
| if [ $rc -ne 0 ] ; then | |
| return 2 | |
| fi | |
| two=$(echo "$full" | grep -m1 . | cut -c-2) | |
| # Make sure full splice has the same contents as a standard read. | |
| echo " splicing 4096 bytes ..." >&2 | |
| if ! do_splice "$filename" 4096 "$full" "full read" ; then | |
| return 1 | |
| fi | |
| # Make sure a partial splice see the first two characters. | |
| echo " splicing 2 bytes ..." >&2 | |
| if ! do_splice "$filename" 2 "$two" "'$two'" ; then | |
| return 1 | |
| fi | |
| return 0 | |
| } | |
| ### /proc/$pid/ has no splice interface; these should all fail. | |
| expect_failure "proc_single_open(), seq_read() splice" test_splice /proc/$$/limits | |
| expect_failure "special open(), seq_read() splice" test_splice /proc/$$/comm | |
| ### /proc/sys/ has a splice interface; these should all succeed. | |
| expect_success "proc_handler: proc_dointvec_minmax() splice" test_splice /proc/sys/fs/nr_open | |
| expect_success "proc_handler: proc_dostring() splice" test_splice /proc/sys/kernel/modprobe | |
| expect_success "proc_handler: special read splice" test_splice /proc/sys/kernel/version | |
| ### /sys/ has no splice interface; these should all fail. | |
| if ! [ -d /sys/module/test_module/sections ] ; then | |
| expect_success "test_module kernel module load" modprobe test_module | |
| fi | |
| expect_success "kernfs attr splice" test_splice /sys/module/test_module/coresize | |
| expect_success "kernfs binattr splice" test_splice /sys/module/test_module/sections/.init.text | |
| exit $ret |