arch/arm/boot/dts/st/stm32mp133c-prihmb.dts - linux - Git at Google

 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /dts-v1/;

 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/regulator/st,stm32mp13-regulator.h>
 #include "stm32mp133.dtsi"
 #include "stm32mp13xc.dtsi"
 #include "stm32mp13-pinctrl.dtsi"

 / {
 	model = "Priva E-Measuringbox board";
 	compatible = "pri,prihmb", "st,stm32mp133";

 	aliases {
 		ethernet0 = &ethernet1;
 		mdio-gpio0 = &mdio0;
 		mmc0 = &sdmmc1;
 		mmc1 = &sdmmc2;
 		serial0 = &uart4;
 		serial1 = &usart6;
 		serial2 = &uart7;
 	};

 	chosen {
 		stdout-path = "serial0:115200n8";
 	};

 	counter-0 {
 		compatible = "interrupt-counter";
 		gpios = <&gpioa 11 GPIO_ACTIVE_HIGH>;
 	};

 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;

 		button-reset {
 			label = "reset-button";
 			linux,code = <BTN_1>;
 			gpios = <&gpioi 7 GPIO_ACTIVE_LOW>;
 		};
 	};

 	leds {
 		compatible = "gpio-leds";

 		led-blue {
 			function = LED_FUNCTION_HEARTBEAT;
 			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
 	};

 	led-controller-0 {
 		compatible = "pwm-leds-multicolor";

 		multi-led {
 			color = <LED_COLOR_ID_RGB>;
 			function = LED_FUNCTION_STATUS;
 			max-brightness = <255>;

 			led-red {
 				active-low;
 				color = <LED_COLOR_ID_RED>;
 				pwms = <&pwm2 2 1000000 1>;
 			};

 			led-green {
 				active-low;
 				color = <LED_COLOR_ID_GREEN>;
 				pwms = <&pwm1 1 1000000 1>;
 			};

 			led-blue {
 				active-low;
 				color = <LED_COLOR_ID_BLUE>;
 				pwms = <&pwm1 2 1000000 1>;
 			};
 		};
 	};

 	led-controller-1 {
 		compatible = "pwm-leds-multicolor";

 		multi-led {
 			color = <LED_COLOR_ID_RGB>;
 			function = LED_FUNCTION_STATUS;
 			max-brightness = <255>;

 			led-red {
 				active-low;
 				color = <LED_COLOR_ID_RED>;
 				pwms = <&pwm1 0 1000000 1>;
 			};

 			led-green {
 				active-low;
 				color = <LED_COLOR_ID_GREEN>;
 				pwms = <&pwm2 0 1000000 1>;
 			};

 			led-blue {
 				active-low;
 				color = <LED_COLOR_ID_BLUE>;
 				pwms = <&pwm2 1 1000000 1>;
 			};
 		};
 	};

 	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
 	 * stmmac MDC clock without reducing system bus rate, we need to use
 	 * gpio based MDIO bus.
 	 */
 	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		gpios = <&gpiog 2 GPIO_ACTIVE_HIGH
 			 &gpioa 2 GPIO_ACTIVE_HIGH>;

 		/* TI DP83TD510E */
 		phy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-id2000.0181";
 			reg = <0>;
 			interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
 			reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10>;
 			reset-deassert-us = <35>;
 		};
 	};

 	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xc0000000 0x10000000>;
 	};

 	reg_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};

 	reserved-memory {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;

 		optee@ce000000 {
 			reg = <0xce000000 0x02000000>;
 			no-map;
 		};
 	};
 };

 &adc_1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&adc_1_pins_a>;
 	vdda-supply = <&reg_3v3>;
 	vref-supply = <&reg_3v3>;
 	status = "okay";
 };

 &adc1 {
 	status = "okay";

 	channel@0 { /* Fan current PC0*/
 		reg = <0>;
 		st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
 	};
 	channel@11 { /* Fan voltage */
 		reg = <11>;
 		st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
 	};
 	channel@15 { /* Supply voltage */
 		reg = <15>;
 		st,min-sample-time-ns = <10000>;  /* 10µs sampling time */
 	};
 };

 &dts {
 	status = "okay";
 };

 &ethernet1 {
 	status = "okay";
 	pinctrl-0 = <&ethernet1_rmii_pins_a>;
 	pinctrl-1 = <&ethernet1_rmii_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rmii";
 	phy-handle = <&phy0>;
 };

 &i2c1 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&i2c1_pins_a>;
 	pinctrl-1 = <&i2c1_sleep_pins_a>;
 	clock-frequency = <100000>;
 	/delete-property/dmas;
 	/delete-property/dma-names;
 	status = "okay";

 	board-sensor@48 {
 		compatible = "ti,tmp1075";
 		reg = <0x48>;
 		vs-supply = <&reg_3v3>;
 	};
 };

 &{i2c1_pins_a/pins} {
 	pinmux = <STM32_PINMUX('D', 3, AF5)>, /* I2C1_SCL */
 		 <STM32_PINMUX('B', 8, AF4)>; /* I2C1_SDA */
 	bias-disable;
 	drive-open-drain;
 	slew-rate = <0>;
 };

 &{i2c1_sleep_pins_a/pins} {
 	pinmux = <STM32_PINMUX('D', 3, ANALOG)>, /* I2C1_SCL */
 		 <STM32_PINMUX('B', 8, ANALOG)>; /* I2C1_SDA */
 };

 &iwdg2 {
 	timeout-sec = <32>;
 	status = "okay";
 };

 /* SD card without Card-detect */
 &sdmmc1 {
 	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
 	broken-cd;
 	no-sdio;
 	no-1-8-v;
 	st,neg-edge;
 	bus-width = <4>;
 	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };

 /* EMMC */
 &sdmmc2 {
 	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
 	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
 	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
 	non-removable;
 	no-sd;
 	no-sdio;
 	no-1-8-v;
 	st,neg-edge;
 	mmc-ddr-3_3v;
 	bus-width = <8>;
 	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };

 &timers1 {
 	status = "okay";
 	/delete-property/dmas;
 	/delete-property/dma-names;

 	pwm1: pwm {
 		pinctrl-0 = <&pwm1_pins_a>;
 		pinctrl-1 = <&pwm1_sleep_pins_a>;
 		pinctrl-names = "default", "sleep";
 		status = "okay";
 	};
 };

 &timers4 {
 	status = "okay";
 	/delete-property/dmas;
 	/delete-property/dma-names;

 	pwm2: pwm {
 		pinctrl-0 = <&pwm4_pins_a>;
 		pinctrl-1 = <&pwm4_sleep_pins_a>;
 		pinctrl-names = "default", "sleep";
 		status = "okay";
 	};
 };

 /* Fan PWM */
 &timers5 {
 	status = "okay";

 	pwm3: pwm {
 		pinctrl-0 = <&pwm5_pins_a>;
 		pinctrl-1 = <&pwm5_sleep_pins_a>;
 		pinctrl-names = "default", "sleep";
 		status = "okay";
 	};
 };

 &timers2 {
 	status = "okay";

 	timer@1 {
 		status = "okay";
 	};
 };

 &uart4 {
 	pinctrl-names = "default", "sleep", "idle";
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
 	/delete-property/dmas;
 	/delete-property/dma-names;
 	status = "okay";
 };

 &uart7 {
 	pinctrl-names = "default", "sleep", "idle";
 	pinctrl-0 = <&uart7_pins_a>;
 	pinctrl-1 = <&uart7_sleep_pins_a>;
 	pinctrl-2 = <&uart7_idle_pins_a>;
 	/delete-property/dmas;
 	/delete-property/dma-names;
 	status = "okay";
 };

 &usart6 {
 	pinctrl-names = "default", "sleep", "idle";
 	pinctrl-0 = <&usart6_pins_a>;
 	pinctrl-1 = <&usart6_sleep_pins_a>;
 	pinctrl-2 = <&usart6_idle_pins_a>;
 	linux,rs485-enabled-at-boot-time;
 	/delete-property/dmas;
 	/delete-property/dma-names;
 	status = "okay";
 };

 &pinctrl {
 	adc_1_pins_a: adc1-0 {
 		pins {
 			pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* ADC1 in0 */
 				 <STM32_PINMUX('C', 2, ANALOG)>, /* ADC1 in15 */
 				 <STM32_PINMUX('F', 13, ANALOG)>; /* ADC1 in11 */
 		};
 	};

 	ethernet1_rmii_pins_a: rmii-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
 				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
 				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
 				 <STM32_PINMUX('A', 1, AF11)>;   /* ETH1_RMII_REF_CLK */
 			bias-disable;
 			drive-push-pull;
 			slew-rate = <2>;
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
 				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
 				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
 			bias-disable;
 		};
 	};

 	ethernet1_rmii_sleep_pins_a: rmii-sleep-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
 				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
 				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
 				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
 				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
 				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
 				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
 		};
 	};

 	pwm1_pins_a: pwm1-0 {
 		pins {
 			pinmux = <STM32_PINMUX('E', 9, AF1)>, /* TIM1_CH1 */
 				 <STM32_PINMUX('E', 11, AF1)>, /* TIM1_CH2 */
 				 <STM32_PINMUX('E', 13, AF1)>; /* TIM1_CH3 */
 			bias-pull-down;
 			drive-push-pull;
 			slew-rate = <0>;
 		};
 	};

 	pwm1_sleep_pins_a: pwm1-sleep-0 {
 		pins {
 			pinmux = <STM32_PINMUX('E', 9, ANALOG)>, /* TIM1_CH1 */
 				 <STM32_PINMUX('E', 11, ANALOG)>, /* TIM1_CH2 */
 				 <STM32_PINMUX('E', 13, ANALOG)>; /* TIM1_CH3 */
 		};
 	};

 	pwm4_pins_a: pwm4-0 {
 		pins {
 			pinmux = <STM32_PINMUX('D', 12, AF2)>, /* TIM4_CH1 */
 				 <STM32_PINMUX('B', 7, AF2)>, /* TIM4_CH2 */
 				 <STM32_PINMUX('D', 14, AF2)>; /* TIM4_CH3 */
 			bias-pull-down;
 			drive-push-pull;
 			slew-rate = <0>;
 		};
 	};

 	pwm4_sleep_pins_a: pwm4-sleep-0 {
 		pins {
 			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* TIM4_CH1 */
 				 <STM32_PINMUX('B', 7, ANALOG)>, /* TIM4_CH2 */
 				 <STM32_PINMUX('D', 14, ANALOG)>; /* TIM4_CH3 */
 		};
 	};
 	pwm5_pins_a: pwm5-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
 		};
 	};

 	pwm5_sleep_pins_a: pwm5-sleep-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
 		};
 	};

 	uart7_pins_a: uart7-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART_TX */
 			bias-disable;
 			drive-push-pull;
 			slew-rate = <0>;
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
 			bias-pull-up;
 		};
 	};

 	uart7_idle_pins_a: uart7-idle-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* UART7_TX */
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
 			bias-pull-up;
 		};
 	};

 	uart7_sleep_pins_a: uart7-sleep-0 {
 		pins {
 			pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* UART7_TX */
 				 <STM32_PINMUX('E', 10, ANALOG)>; /* UART7_RX */
 		};
 	};

 	usart6_pins_a: usart6-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('F', 8, AF7)>, /* USART6_TX */
 				 <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
 			bias-disable;
 			drive-push-pull;
 			slew-rate = <0>;
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
 			bias-disable;
 		};
 	};

 	usart6_idle_pins_a: usart6-idle-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('F', 8, ANALOG)>; /* USART6_TX */
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
 			bias-disable;
 			drive-push-pull;
 			slew-rate = <0>;
 		};
 		pins3 {
 			pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
 			bias-disable;
 		};
 	};

 	usart6_sleep_pins_a: usart6-sleep-0 {
 		pins {
 			pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* USART6_TX */
 				 <STM32_PINMUX('F', 10, ANALOG)>, /* USART6_DE */
 				 <STM32_PINMUX('H', 11, ANALOG)>; /* USART6_RX */
 		};
 	};
 };
	// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
	/dts-v1/;

	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/input/input.h>
	#include <dt-bindings/leds/common.h>
	#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
	#include "stm32mp133.dtsi"
	#include "stm32mp13xc.dtsi"
	#include "stm32mp13-pinctrl.dtsi"

	/ {
	model = "Priva E-Measuringbox board";
	compatible = "pri,prihmb", "st,stm32mp133";

	aliases {
	ethernet0 = &ethernet1;
	mdio-gpio0 = &mdio0;
	mmc0 = &sdmmc1;
	mmc1 = &sdmmc2;
	serial0 = &uart4;
	serial1 = &usart6;
	serial2 = &uart7;
	};

	chosen {
	stdout-path = "serial0:115200n8";
	};

	counter-0 {
	compatible = "interrupt-counter";
	gpios = <&gpioa 11 GPIO_ACTIVE_HIGH>;
	};

	gpio-keys {
	compatible = "gpio-keys";
	autorepeat;

	button-reset {
	label = "reset-button";
	linux,code = <BTN_1>;
	gpios = <&gpioi 7 GPIO_ACTIVE_LOW>;
	};
	};

	leds {
	compatible = "gpio-leds";

	led-blue {
	function = LED_FUNCTION_HEARTBEAT;
	color = <LED_COLOR_ID_BLUE>;
	gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
	linux,default-trigger = "heartbeat";
	default-state = "off";
	};
	};

	led-controller-0 {
	compatible = "pwm-leds-multicolor";

	multi-led {
	color = <LED_COLOR_ID_RGB>;
	function = LED_FUNCTION_STATUS;
	max-brightness = <255>;

	led-red {
	active-low;
	color = <LED_COLOR_ID_RED>;
	pwms = <&pwm2 2 1000000 1>;
	};

	led-green {
	active-low;
	color = <LED_COLOR_ID_GREEN>;
	pwms = <&pwm1 1 1000000 1>;
	};

	led-blue {
	active-low;
	color = <LED_COLOR_ID_BLUE>;
	pwms = <&pwm1 2 1000000 1>;
	};
	};
	};

	led-controller-1 {
	compatible = "pwm-leds-multicolor";

	multi-led {
	color = <LED_COLOR_ID_RGB>;
	function = LED_FUNCTION_STATUS;
	max-brightness = <255>;

	led-red {
	active-low;
	color = <LED_COLOR_ID_RED>;
	pwms = <&pwm1 0 1000000 1>;
	};

	led-green {
	active-low;
	color = <LED_COLOR_ID_GREEN>;
	pwms = <&pwm2 0 1000000 1>;
	};

	led-blue {
	active-low;
	color = <LED_COLOR_ID_BLUE>;
	pwms = <&pwm2 1 1000000 1>;
	};
	};
	};

	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
	* stmmac MDC clock without reducing system bus rate, we need to use
	* gpio based MDIO bus.
	*/
	mdio0: mdio {
	compatible = "virtual,mdio-gpio";
	#address-cells = <1>;
	#size-cells = <0>;
	gpios = <&gpiog 2 GPIO_ACTIVE_HIGH
	&gpioa 2 GPIO_ACTIVE_HIGH>;

	/* TI DP83TD510E */
	phy0: ethernet-phy@0 {
	compatible = "ethernet-phy-id2000.0181";
	reg = <0>;
	interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
	reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
	reset-assert-us = <10>;
	reset-deassert-us = <35>;
	};
	};

	memory@c0000000 {
	device_type = "memory";
	reg = <0xc0000000 0x10000000>;
	};

	reg_3v3: regulator-3v3 {
	compatible = "regulator-fixed";
	regulator-name = "3v3";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	};

	reserved-memory {
	#address-cells = <1>;
	#size-cells = <1>;
	ranges;

	optee@ce000000 {
	reg = <0xce000000 0x02000000>;
	no-map;
	};
	};
	};

	&adc_1 {
	pinctrl-names = "default";
	pinctrl-0 = <&adc_1_pins_a>;
	vdda-supply = <&reg_3v3>;
	vref-supply = <&reg_3v3>;
	status = "okay";
	};

	&adc1 {
	status = "okay";

	channel@0 { /* Fan current PC0*/
	reg = <0>;
	st,min-sample-time-ns = <10000>; /* 10µs sampling time */
	};
	channel@11 { /* Fan voltage */
	reg = <11>;
	st,min-sample-time-ns = <10000>; /* 10µs sampling time */
	};
	channel@15 { /* Supply voltage */
	reg = <15>;
	st,min-sample-time-ns = <10000>; /* 10µs sampling time */
	};
	};

	&dts {
	status = "okay";
	};

	&ethernet1 {
	status = "okay";
	pinctrl-0 = <&ethernet1_rmii_pins_a>;
	pinctrl-1 = <&ethernet1_rmii_sleep_pins_a>;
	pinctrl-names = "default", "sleep";
	phy-mode = "rmii";
	phy-handle = <&phy0>;
	};

	&i2c1 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&i2c1_pins_a>;
	pinctrl-1 = <&i2c1_sleep_pins_a>;
	clock-frequency = <100000>;
	/delete-property/dmas;
	/delete-property/dma-names;
	status = "okay";

	board-sensor@48 {
	compatible = "ti,tmp1075";
	reg = <0x48>;
	vs-supply = <&reg_3v3>;
	};
	};

	&{i2c1_pins_a/pins} {
	pinmux = <STM32_PINMUX('D', 3, AF5)>, /* I2C1_SCL */
	<STM32_PINMUX('B', 8, AF4)>; /* I2C1_SDA */
	bias-disable;
	drive-open-drain;
	slew-rate = <0>;
	};

	&{i2c1_sleep_pins_a/pins} {
	pinmux = <STM32_PINMUX('D', 3, ANALOG)>, /* I2C1_SCL */
	<STM32_PINMUX('B', 8, ANALOG)>; /* I2C1_SDA */
	};

	&iwdg2 {
	timeout-sec = <32>;
	status = "okay";
	};

	/* SD card without Card-detect */
	&sdmmc1 {
	pinctrl-names = "default", "opendrain", "sleep";
	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
	broken-cd;
	no-sdio;
	no-1-8-v;
	st,neg-edge;
	bus-width = <4>;
	vmmc-supply = <&reg_3v3>;
	status = "okay";
	};

	/* EMMC */
	&sdmmc2 {
	pinctrl-names = "default", "opendrain", "sleep";
	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
	non-removable;
	no-sd;
	no-sdio;
	no-1-8-v;
	st,neg-edge;
	mmc-ddr-3_3v;
	bus-width = <8>;
	vmmc-supply = <&reg_3v3>;
	status = "okay";
	};

	&timers1 {
	status = "okay";
	/delete-property/dmas;
	/delete-property/dma-names;

	pwm1: pwm {
	pinctrl-0 = <&pwm1_pins_a>;
	pinctrl-1 = <&pwm1_sleep_pins_a>;
	pinctrl-names = "default", "sleep";
	status = "okay";
	};
	};

	&timers4 {
	status = "okay";
	/delete-property/dmas;
	/delete-property/dma-names;

	pwm2: pwm {
	pinctrl-0 = <&pwm4_pins_a>;
	pinctrl-1 = <&pwm4_sleep_pins_a>;
	pinctrl-names = "default", "sleep";
	status = "okay";
	};
	};

	/* Fan PWM */
	&timers5 {
	status = "okay";

	pwm3: pwm {
	pinctrl-0 = <&pwm5_pins_a>;
	pinctrl-1 = <&pwm5_sleep_pins_a>;
	pinctrl-names = "default", "sleep";
	status = "okay";
	};
	};

	&timers2 {
	status = "okay";

	timer@1 {
	status = "okay";
	};
	};

	&uart4 {
	pinctrl-names = "default", "sleep", "idle";
	pinctrl-0 = <&uart4_pins_a>;
	pinctrl-1 = <&uart4_sleep_pins_a>;
	pinctrl-2 = <&uart4_idle_pins_a>;
	/delete-property/dmas;
	/delete-property/dma-names;
	status = "okay";
	};

	&uart7 {
	pinctrl-names = "default", "sleep", "idle";
	pinctrl-0 = <&uart7_pins_a>;
	pinctrl-1 = <&uart7_sleep_pins_a>;
	pinctrl-2 = <&uart7_idle_pins_a>;
	/delete-property/dmas;
	/delete-property/dma-names;
	status = "okay";
	};

	&usart6 {
	pinctrl-names = "default", "sleep", "idle";
	pinctrl-0 = <&usart6_pins_a>;
	pinctrl-1 = <&usart6_sleep_pins_a>;
	pinctrl-2 = <&usart6_idle_pins_a>;
	linux,rs485-enabled-at-boot-time;
	/delete-property/dmas;
	/delete-property/dma-names;
	status = "okay";
	};

	&pinctrl {
	adc_1_pins_a: adc1-0 {
	pins {
	pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* ADC1 in0 */
	<STM32_PINMUX('C', 2, ANALOG)>, /* ADC1 in15 */
	<STM32_PINMUX('F', 13, ANALOG)>; /* ADC1 in11 */
	};
	};

	ethernet1_rmii_pins_a: rmii-0 {
	pins1 {
	pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
	<STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
	<STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
	<STM32_PINMUX('A', 1, AF11)>; /* ETH1_RMII_REF_CLK */
	bias-disable;
	drive-push-pull;
	slew-rate = <2>;
	};
	pins2 {
	pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */
	<STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */
	<STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */
	bias-disable;
	};
	};

	ethernet1_rmii_sleep_pins_a: rmii-sleep-0 {
	pins1 {
	pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
	<STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
	<STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
	<STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */
	<STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */
	<STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */
	<STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */
	};
	};

	pwm1_pins_a: pwm1-0 {
	pins {
	pinmux = <STM32_PINMUX('E', 9, AF1)>, /* TIM1_CH1 */
	<STM32_PINMUX('E', 11, AF1)>, /* TIM1_CH2 */
	<STM32_PINMUX('E', 13, AF1)>; /* TIM1_CH3 */
	bias-pull-down;
	drive-push-pull;
	slew-rate = <0>;
	};
	};

	pwm1_sleep_pins_a: pwm1-sleep-0 {
	pins {
	pinmux = <STM32_PINMUX('E', 9, ANALOG)>, /* TIM1_CH1 */
	<STM32_PINMUX('E', 11, ANALOG)>, /* TIM1_CH2 */
	<STM32_PINMUX('E', 13, ANALOG)>; /* TIM1_CH3 */
	};
	};

	pwm4_pins_a: pwm4-0 {
	pins {
	pinmux = <STM32_PINMUX('D', 12, AF2)>, /* TIM4_CH1 */
	<STM32_PINMUX('B', 7, AF2)>, /* TIM4_CH2 */
	<STM32_PINMUX('D', 14, AF2)>; /* TIM4_CH3 */
	bias-pull-down;
	drive-push-pull;
	slew-rate = <0>;
	};
	};

	pwm4_sleep_pins_a: pwm4-sleep-0 {
	pins {
	pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* TIM4_CH1 */
	<STM32_PINMUX('B', 7, ANALOG)>, /* TIM4_CH2 */
	<STM32_PINMUX('D', 14, ANALOG)>; /* TIM4_CH3 */
	};
	};
	pwm5_pins_a: pwm5-0 {
	pins {
	pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
	};
	};

	pwm5_sleep_pins_a: pwm5-sleep-0 {
	pins {
	pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
	};
	};

	uart7_pins_a: uart7-0 {
	pins1 {
	pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART_TX */
	bias-disable;
	drive-push-pull;
	slew-rate = <0>;
	};
	pins2 {
	pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
	bias-pull-up;
	};
	};

	uart7_idle_pins_a: uart7-idle-0 {
	pins1 {
	pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* UART7_TX */
	};
	pins2 {
	pinmux = <STM32_PINMUX('E', 10, AF7)>; /* UART7_RX */
	bias-pull-up;
	};
	};

	uart7_sleep_pins_a: uart7-sleep-0 {
	pins {
	pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* UART7_TX */
	<STM32_PINMUX('E', 10, ANALOG)>; /* UART7_RX */
	};
	};

	usart6_pins_a: usart6-0 {
	pins1 {
	pinmux = <STM32_PINMUX('F', 8, AF7)>, /* USART6_TX */
	<STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
	bias-disable;
	drive-push-pull;
	slew-rate = <0>;
	};
	pins2 {
	pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
	bias-disable;
	};
	};

	usart6_idle_pins_a: usart6-idle-0 {
	pins1 {
	pinmux = <STM32_PINMUX('F', 8, ANALOG)>; /* USART6_TX */
	};
	pins2 {
	pinmux = <STM32_PINMUX('F', 10, AF7)>; /* USART6_DE */
	bias-disable;
	drive-push-pull;
	slew-rate = <0>;
	};
	pins3 {
	pinmux = <STM32_PINMUX('H', 11, AF7)>; /* USART6_RX */
	bias-disable;
	};
	};

	usart6_sleep_pins_a: usart6-sleep-0 {
	pins {
	pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* USART6_TX */
	<STM32_PINMUX('F', 10, ANALOG)>, /* USART6_DE */
	<STM32_PINMUX('H', 11, ANALOG)>; /* USART6_RX */
	};
	};
	};