| // SPDX-License-Identifier: GPL-2.0 | |
| /* Copyright (c) 2018 Intel Corporation */ | |
| #include <linux/pci.h> | |
| #include <linux/delay.h> | |
| #include "igc_mac.h" | |
| #include "igc_hw.h" | |
| /** | |
| * igc_disable_pcie_master - Disables PCI-express master access | |
| * @hw: pointer to the HW structure | |
| * | |
| * Returns 0 (0) if successful, else returns -10 | |
| * (-IGC_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused | |
| * the master requests to be disabled. | |
| * | |
| * Disables PCI-Express master access and verifies there are no pending | |
| * requests. | |
| */ | |
| s32 igc_disable_pcie_master(struct igc_hw *hw) | |
| { | |
| s32 timeout = MASTER_DISABLE_TIMEOUT; | |
| s32 ret_val = 0; | |
| u32 ctrl; | |
| ctrl = rd32(IGC_CTRL); | |
| ctrl |= IGC_CTRL_GIO_MASTER_DISABLE; | |
| wr32(IGC_CTRL, ctrl); | |
| while (timeout) { | |
| if (!(rd32(IGC_STATUS) & | |
| IGC_STATUS_GIO_MASTER_ENABLE)) | |
| break; | |
| usleep_range(2000, 3000); | |
| timeout--; | |
| } | |
| if (!timeout) { | |
| hw_dbg("Master requests are pending.\n"); | |
| ret_val = -IGC_ERR_MASTER_REQUESTS_PENDING; | |
| goto out; | |
| } | |
| out: | |
| return ret_val; | |
| } | |
| /** | |
| * igc_init_rx_addrs - Initialize receive addresses | |
| * @hw: pointer to the HW structure | |
| * @rar_count: receive address registers | |
| * | |
| * Setup the receive address registers by setting the base receive address | |
| * register to the devices MAC address and clearing all the other receive | |
| * address registers to 0. | |
| */ | |
| void igc_init_rx_addrs(struct igc_hw *hw, u16 rar_count) | |
| { | |
| u8 mac_addr[ETH_ALEN] = {0}; | |
| u32 i; | |
| /* Setup the receive address */ | |
| hw_dbg("Programming MAC Address into RAR[0]\n"); | |
| hw->mac.ops.rar_set(hw, hw->mac.addr, 0); | |
| /* Zero out the other (rar_entry_count - 1) receive addresses */ | |
| hw_dbg("Clearing RAR[1-%u]\n", rar_count - 1); | |
| for (i = 1; i < rar_count; i++) | |
| hw->mac.ops.rar_set(hw, mac_addr, i); | |
| } | |
| /** | |
| * igc_set_fc_watermarks - Set flow control high/low watermarks | |
| * @hw: pointer to the HW structure | |
| * | |
| * Sets the flow control high/low threshold (watermark) registers. If | |
| * flow control XON frame transmission is enabled, then set XON frame | |
| * transmission as well. | |
| */ | |
| static s32 igc_set_fc_watermarks(struct igc_hw *hw) | |
| { | |
| u32 fcrtl = 0, fcrth = 0; | |
| /* Set the flow control receive threshold registers. Normally, | |
| * these registers will be set to a default threshold that may be | |
| * adjusted later by the driver's runtime code. However, if the | |
| * ability to transmit pause frames is not enabled, then these | |
| * registers will be set to 0. | |
| */ | |
| if (hw->fc.current_mode & igc_fc_tx_pause) { | |
| /* We need to set up the Receive Threshold high and low water | |
| * marks as well as (optionally) enabling the transmission of | |
| * XON frames. | |
| */ | |
| fcrtl = hw->fc.low_water; | |
| if (hw->fc.send_xon) | |
| fcrtl |= IGC_FCRTL_XONE; | |
| fcrth = hw->fc.high_water; | |
| } | |
| wr32(IGC_FCRTL, fcrtl); | |
| wr32(IGC_FCRTH, fcrth); | |
| return 0; | |
| } | |
| /** | |
| * igc_setup_link - Setup flow control and link settings | |
| * @hw: pointer to the HW structure | |
| * | |
| * Determines which flow control settings to use, then configures flow | |
| * control. Calls the appropriate media-specific link configuration | |
| * function. Assuming the adapter has a valid link partner, a valid link | |
| * should be established. Assumes the hardware has previously been reset | |
| * and the transmitter and receiver are not enabled. | |
| */ | |
| s32 igc_setup_link(struct igc_hw *hw) | |
| { | |
| s32 ret_val = 0; | |
| /* In the case of the phy reset being blocked, we already have a link. | |
| * We do not need to set it up again. | |
| */ | |
| if (igc_check_reset_block(hw)) | |
| goto out; | |
| /* If requested flow control is set to default, set flow control | |
| * to both 'rx' and 'tx' pause frames. | |
| */ | |
| if (hw->fc.requested_mode == igc_fc_default) | |
| hw->fc.requested_mode = igc_fc_full; | |
| /* We want to save off the original Flow Control configuration just | |
| * in case we get disconnected and then reconnected into a different | |
| * hub or switch with different Flow Control capabilities. | |
| */ | |
| hw->fc.current_mode = hw->fc.requested_mode; | |
| hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode); | |
| /* Call the necessary media_type subroutine to configure the link. */ | |
| ret_val = hw->mac.ops.setup_physical_interface(hw); | |
| if (ret_val) | |
| goto out; | |
| /* Initialize the flow control address, type, and PAUSE timer | |
| * registers to their default values. This is done even if flow | |
| * control is disabled, because it does not hurt anything to | |
| * initialize these registers. | |
| */ | |
| hw_dbg("Initializing the Flow Control address, type and timer regs\n"); | |
| wr32(IGC_FCT, FLOW_CONTROL_TYPE); | |
| wr32(IGC_FCAH, FLOW_CONTROL_ADDRESS_HIGH); | |
| wr32(IGC_FCAL, FLOW_CONTROL_ADDRESS_LOW); | |
| wr32(IGC_FCTTV, hw->fc.pause_time); | |
| ret_val = igc_set_fc_watermarks(hw); | |
| out: | |
| return ret_val; | |
| } | |
| /** | |
| * igc_force_mac_fc - Force the MAC's flow control settings | |
| * @hw: pointer to the HW structure | |
| * | |
| * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the | |
| * device control register to reflect the adapter settings. TFCE and RFCE | |
| * need to be explicitly set by software when a copper PHY is used because | |
| * autonegotiation is managed by the PHY rather than the MAC. Software must | |
| * also configure these bits when link is forced on a fiber connection. | |
| */ | |
| s32 igc_force_mac_fc(struct igc_hw *hw) | |
| { | |
| s32 ret_val = 0; | |
| u32 ctrl; | |
| ctrl = rd32(IGC_CTRL); | |
| /* Because we didn't get link via the internal auto-negotiation | |
| * mechanism (we either forced link or we got link via PHY | |
| * auto-neg), we have to manually enable/disable transmit an | |
| * receive flow control. | |
| * | |
| * The "Case" statement below enables/disable flow control | |
| * according to the "hw->fc.current_mode" parameter. | |
| * | |
| * The possible values of the "fc" parameter are: | |
| * 0: Flow control is completely disabled | |
| * 1: Rx flow control is enabled (we can receive pause | |
| * frames but not send pause frames). | |
| * 2: Tx flow control is enabled (we can send pause frames | |
| * but we do not receive pause frames). | |
| * 3: Both Rx and TX flow control (symmetric) is enabled. | |
| * other: No other values should be possible at this point. | |
| */ | |
| hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode); | |
| switch (hw->fc.current_mode) { | |
| case igc_fc_none: | |
| ctrl &= (~(IGC_CTRL_TFCE | IGC_CTRL_RFCE)); | |
| break; | |
| case igc_fc_rx_pause: | |
| ctrl &= (~IGC_CTRL_TFCE); | |
| ctrl |= IGC_CTRL_RFCE; | |
| break; | |
| case igc_fc_tx_pause: | |
| ctrl &= (~IGC_CTRL_RFCE); | |
| ctrl |= IGC_CTRL_TFCE; | |
| break; | |
| case igc_fc_full: | |
| ctrl |= (IGC_CTRL_TFCE | IGC_CTRL_RFCE); | |
| break; | |
| default: | |
| hw_dbg("Flow control param set incorrectly\n"); | |
| ret_val = -IGC_ERR_CONFIG; | |
| goto out; | |
| } | |
| wr32(IGC_CTRL, ctrl); | |
| out: | |
| return ret_val; | |
| } | |
| /** | |
| * igc_clear_hw_cntrs_base - Clear base hardware counters | |
| * @hw: pointer to the HW structure | |
| * | |
| * Clears the base hardware counters by reading the counter registers. | |
| */ | |
| void igc_clear_hw_cntrs_base(struct igc_hw *hw) | |
| { | |
| rd32(IGC_CRCERRS); | |
| rd32(IGC_MPC); | |
| rd32(IGC_SCC); | |
| rd32(IGC_ECOL); | |
| rd32(IGC_MCC); | |
| rd32(IGC_LATECOL); | |
| rd32(IGC_COLC); | |
| rd32(IGC_RERC); | |
| rd32(IGC_DC); | |
| rd32(IGC_RLEC); | |
| rd32(IGC_XONRXC); | |
| rd32(IGC_XONTXC); | |
| rd32(IGC_XOFFRXC); | |
| rd32(IGC_XOFFTXC); | |
| rd32(IGC_FCRUC); | |
| rd32(IGC_GPRC); | |
| rd32(IGC_BPRC); | |
| rd32(IGC_MPRC); | |
| rd32(IGC_GPTC); | |
| rd32(IGC_GORCL); | |
| rd32(IGC_GORCH); | |
| rd32(IGC_GOTCL); | |
| rd32(IGC_GOTCH); | |
| rd32(IGC_RNBC); | |
| rd32(IGC_RUC); | |
| rd32(IGC_RFC); | |
| rd32(IGC_ROC); | |
| rd32(IGC_RJC); | |
| rd32(IGC_TORL); | |
| rd32(IGC_TORH); | |
| rd32(IGC_TOTL); | |
| rd32(IGC_TOTH); | |
| rd32(IGC_TPR); | |
| rd32(IGC_TPT); | |
| rd32(IGC_MPTC); | |
| rd32(IGC_BPTC); | |
| rd32(IGC_PRC64); | |
| rd32(IGC_PRC127); | |
| rd32(IGC_PRC255); | |
| rd32(IGC_PRC511); | |
| rd32(IGC_PRC1023); | |
| rd32(IGC_PRC1522); | |
| rd32(IGC_PTC64); | |
| rd32(IGC_PTC127); | |
| rd32(IGC_PTC255); | |
| rd32(IGC_PTC511); | |
| rd32(IGC_PTC1023); | |
| rd32(IGC_PTC1522); | |
| rd32(IGC_ALGNERRC); | |
| rd32(IGC_RXERRC); | |
| rd32(IGC_TNCRS); | |
| rd32(IGC_HTDPMC); | |
| rd32(IGC_TSCTC); | |
| rd32(IGC_MGTPRC); | |
| rd32(IGC_MGTPDC); | |
| rd32(IGC_MGTPTC); | |
| rd32(IGC_IAC); | |
| rd32(IGC_RPTHC); | |
| rd32(IGC_TLPIC); | |
| rd32(IGC_RLPIC); | |
| rd32(IGC_HGPTC); | |
| rd32(IGC_RXDMTC); | |
| rd32(IGC_HGORCL); | |
| rd32(IGC_HGORCH); | |
| rd32(IGC_HGOTCL); | |
| rd32(IGC_HGOTCH); | |
| rd32(IGC_LENERRS); | |
| } | |
| /** | |
| * igc_rar_set - Set receive address register | |
| * @hw: pointer to the HW structure | |
| * @addr: pointer to the receive address | |
| * @index: receive address array register | |
| * | |
| * Sets the receive address array register at index to the address passed | |
| * in by addr. | |
| */ | |
| void igc_rar_set(struct igc_hw *hw, u8 *addr, u32 index) | |
| { | |
| u32 rar_low, rar_high; | |
| /* HW expects these in little endian so we reverse the byte order | |
| * from network order (big endian) to little endian | |
| */ | |
| rar_low = ((u32)addr[0] | | |
| ((u32)addr[1] << 8) | | |
| ((u32)addr[2] << 16) | ((u32)addr[3] << 24)); | |
| rar_high = ((u32)addr[4] | ((u32)addr[5] << 8)); | |
| /* If MAC address zero, no need to set the AV bit */ | |
| if (rar_low || rar_high) | |
| rar_high |= IGC_RAH_AV; | |
| /* Some bridges will combine consecutive 32-bit writes into | |
| * a single burst write, which will malfunction on some parts. | |
| * The flushes avoid this. | |
| */ | |
| wr32(IGC_RAL(index), rar_low); | |
| wrfl(); | |
| wr32(IGC_RAH(index), rar_high); | |
| wrfl(); | |
| } | |
| /** | |
| * igc_check_for_copper_link - Check for link (Copper) | |
| * @hw: pointer to the HW structure | |
| * | |
| * Checks to see of the link status of the hardware has changed. If a | |
| * change in link status has been detected, then we read the PHY registers | |
| * to get the current speed/duplex if link exists. | |
| */ | |
| s32 igc_check_for_copper_link(struct igc_hw *hw) | |
| { | |
| struct igc_mac_info *mac = &hw->mac; | |
| bool link = false; | |
| s32 ret_val; | |
| /* We only want to go out to the PHY registers to see if Auto-Neg | |
| * has completed and/or if our link status has changed. The | |
| * get_link_status flag is set upon receiving a Link Status | |
| * Change or Rx Sequence Error interrupt. | |
| */ | |
| if (!mac->get_link_status) { | |
| ret_val = 0; | |
| goto out; | |
| } | |
| /* First we want to see if the MII Status Register reports | |
| * link. If so, then we want to get the current speed/duplex | |
| * of the PHY. | |
| */ | |
| ret_val = igc_phy_has_link(hw, 1, 0, &link); | |
| if (ret_val) | |
| goto out; | |
| if (!link) | |
| goto out; /* No link detected */ | |
| mac->get_link_status = false; | |
| /* Check if there was DownShift, must be checked | |
| * immediately after link-up | |
| */ | |
| igc_check_downshift(hw); | |
| /* Auto-Neg is enabled. Auto Speed Detection takes care | |
| * of MAC speed/duplex configuration. So we only need to | |
| * configure Collision Distance in the MAC. | |
| */ | |
| igc_config_collision_dist(hw); | |
| /* Configure Flow Control now that Auto-Neg has completed. | |
| * First, we need to restore the desired flow control | |
| * settings because we may have had to re-autoneg with a | |
| * different link partner. | |
| */ | |
| ret_val = igc_config_fc_after_link_up(hw); | |
| if (ret_val) | |
| hw_dbg("Error configuring flow control\n"); | |
| out: | |
| /* Now that we are aware of our link settings, we can set the LTR | |
| * thresholds. | |
| */ | |
| ret_val = igc_set_ltr_i225(hw, link); | |
| return ret_val; | |
| } | |
| /** | |
| * igc_config_collision_dist - Configure collision distance | |
| * @hw: pointer to the HW structure | |
| * | |
| * Configures the collision distance to the default value and is used | |
| * during link setup. Currently no func pointer exists and all | |
| * implementations are handled in the generic version of this function. | |
| */ | |
| void igc_config_collision_dist(struct igc_hw *hw) | |
| { | |
| u32 tctl; | |
| tctl = rd32(IGC_TCTL); | |
| tctl &= ~IGC_TCTL_COLD; | |
| tctl |= IGC_COLLISION_DISTANCE << IGC_COLD_SHIFT; | |
| wr32(IGC_TCTL, tctl); | |
| wrfl(); | |
| } | |
| /** | |
| * igc_config_fc_after_link_up - Configures flow control after link | |
| * @hw: pointer to the HW structure | |
| * | |
| * Checks the status of auto-negotiation after link up to ensure that the | |
| * speed and duplex were not forced. If the link needed to be forced, then | |
| * flow control needs to be forced also. If auto-negotiation is enabled | |
| * then we configure flow control based on our link partner. | |
| */ | |
| s32 igc_config_fc_after_link_up(struct igc_hw *hw) | |
| { | |
| u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; | |
| u16 speed, duplex; | |
| s32 ret_val = 0; | |
| /* Without autoneg, flow control capability is not exchanged with the | |
| * link partner. IEEE 802.3 prohibits flow control in half-duplex mode. | |
| */ | |
| if (!hw->mac.autoneg_enabled) { | |
| if (hw->mac.forced_speed_duplex == IGC_FORCED_10H || | |
| hw->mac.forced_speed_duplex == IGC_FORCED_100H) | |
| hw->fc.current_mode = igc_fc_none; | |
| goto force_fc; | |
| } | |
| /* In auto-neg, we need to check and see if Auto-Neg has completed, | |
| * and if so, how the PHY and link partner has flow control | |
| * configured. | |
| */ | |
| /* Read the MII Status Register and check to see if AutoNeg | |
| * has completed. We read this twice because this reg has | |
| * some "sticky" (latched) bits. | |
| */ | |
| ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, | |
| &mii_status_reg); | |
| if (ret_val) | |
| return ret_val; | |
| ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, | |
| &mii_status_reg); | |
| if (ret_val) | |
| return ret_val; | |
| if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { | |
| hw_dbg("Copper PHY and Auto Neg has not completed.\n"); | |
| return ret_val; | |
| } | |
| /* The AutoNeg process has completed, so we now need to | |
| * read both the Auto Negotiation Advertisement | |
| * Register (Address 4) and the Auto_Negotiation Base | |
| * Page Ability Register (Address 5) to determine how | |
| * flow control was negotiated. | |
| */ | |
| ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV, | |
| &mii_nway_adv_reg); | |
| if (ret_val) | |
| return ret_val; | |
| ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY, | |
| &mii_nway_lp_ability_reg); | |
| if (ret_val) | |
| return ret_val; | |
| /* Two bits in the Auto Negotiation Advertisement Register | |
| * (Address 4) and two bits in the Auto Negotiation Base | |
| * Page Ability Register (Address 5) determine flow control | |
| * for both the PHY and the link partner. The following | |
| * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, | |
| * 1999, describes these PAUSE resolution bits and how flow | |
| * control is determined based upon these settings. | |
| * NOTE: DC = Don't Care | |
| * | |
| * LOCAL DEVICE | LINK PARTNER | |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution | |
| *-------|---------|-------|---------|-------------------- | |
| * 0 | 0 | DC | DC | igc_fc_none | |
| * 0 | 1 | 0 | DC | igc_fc_none | |
| * 0 | 1 | 1 | 0 | igc_fc_none | |
| * 0 | 1 | 1 | 1 | igc_fc_tx_pause | |
| * 1 | 0 | 0 | DC | igc_fc_none | |
| * 1 | DC | 1 | DC | igc_fc_full | |
| * 1 | 1 | 0 | 0 | igc_fc_none | |
| * 1 | 1 | 0 | 1 | igc_fc_rx_pause | |
| * | |
| * Are both PAUSE bits set to 1? If so, this implies | |
| * Symmetric Flow Control is enabled at both ends. The | |
| * ASM_DIR bits are irrelevant per the spec. | |
| * | |
| * For Symmetric Flow Control: | |
| * | |
| * LOCAL DEVICE | LINK PARTNER | |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result | |
| *-------|---------|-------|---------|-------------------- | |
| * 1 | DC | 1 | DC | IGC_fc_full | |
| * | |
| */ | |
| if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && | |
| (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { | |
| /* Now we need to check if the user selected RX ONLY | |
| * of pause frames. In this case, we had to advertise | |
| * FULL flow control because we could not advertise RX | |
| * ONLY. Hence, we must now check to see if we need to | |
| * turn OFF the TRANSMISSION of PAUSE frames. | |
| */ | |
| if (hw->fc.requested_mode == igc_fc_full) { | |
| hw->fc.current_mode = igc_fc_full; | |
| hw_dbg("Flow Control = FULL.\n"); | |
| } else { | |
| hw->fc.current_mode = igc_fc_rx_pause; | |
| hw_dbg("Flow Control = RX PAUSE frames only.\n"); | |
| } | |
| } | |
| /* For receiving PAUSE frames ONLY. | |
| * | |
| * LOCAL DEVICE | LINK PARTNER | |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result | |
| *-------|---------|-------|---------|-------------------- | |
| * 0 | 1 | 1 | 1 | igc_fc_tx_pause | |
| */ | |
| else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && | |
| (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && | |
| (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && | |
| (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { | |
| hw->fc.current_mode = igc_fc_tx_pause; | |
| hw_dbg("Flow Control = TX PAUSE frames only.\n"); | |
| } | |
| /* For transmitting PAUSE frames ONLY. | |
| * | |
| * LOCAL DEVICE | LINK PARTNER | |
| * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result | |
| *-------|---------|-------|---------|-------------------- | |
| * 1 | 1 | 0 | 1 | igc_fc_rx_pause | |
| */ | |
| else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && | |
| (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && | |
| !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && | |
| (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { | |
| hw->fc.current_mode = igc_fc_rx_pause; | |
| hw_dbg("Flow Control = RX PAUSE frames only.\n"); | |
| } | |
| /* Per the IEEE spec, at this point flow control should be | |
| * disabled. However, we want to consider that we could | |
| * be connected to a legacy switch that doesn't advertise | |
| * desired flow control, but can be forced on the link | |
| * partner. So if we advertised no flow control, that is | |
| * what we will resolve to. If we advertised some kind of | |
| * receive capability (Rx Pause Only or Full Flow Control) | |
| * and the link partner advertised none, we will configure | |
| * ourselves to enable Rx Flow Control only. We can do | |
| * this safely for two reasons: If the link partner really | |
| * didn't want flow control enabled, and we enable Rx, no | |
| * harm done since we won't be receiving any PAUSE frames | |
| * anyway. If the intent on the link partner was to have | |
| * flow control enabled, then by us enabling RX only, we | |
| * can at least receive pause frames and process them. | |
| * This is a good idea because in most cases, since we are | |
| * predominantly a server NIC, more times than not we will | |
| * be asked to delay transmission of packets than asking | |
| * our link partner to pause transmission of frames. | |
| */ | |
| else if ((hw->fc.requested_mode == igc_fc_none) || | |
| (hw->fc.requested_mode == igc_fc_tx_pause) || | |
| (hw->fc.strict_ieee)) { | |
| hw->fc.current_mode = igc_fc_none; | |
| hw_dbg("Flow Control = NONE.\n"); | |
| } else { | |
| hw->fc.current_mode = igc_fc_rx_pause; | |
| hw_dbg("Flow Control = RX PAUSE frames only.\n"); | |
| } | |
| /* Now we need to do one last check... If we auto- | |
| * negotiated to HALF DUPLEX, flow control should not be | |
| * enabled per IEEE 802.3 spec. | |
| */ | |
| ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex); | |
| if (ret_val) { | |
| hw_dbg("Error getting link speed and duplex\n"); | |
| return ret_val; | |
| } | |
| if (duplex == HALF_DUPLEX) | |
| hw->fc.current_mode = igc_fc_none; | |
| /* Now we call a subroutine to actually force the MAC | |
| * controller to use the correct flow control settings. | |
| */ | |
| force_fc: | |
| ret_val = igc_force_mac_fc(hw); | |
| if (ret_val) { | |
| hw_dbg("Error forcing flow control settings\n"); | |
| return ret_val; | |
| } | |
| return ret_val; | |
| } | |
| /** | |
| * igc_get_auto_rd_done - Check for auto read completion | |
| * @hw: pointer to the HW structure | |
| * | |
| * Check EEPROM for Auto Read done bit. | |
| */ | |
| s32 igc_get_auto_rd_done(struct igc_hw *hw) | |
| { | |
| s32 ret_val = 0; | |
| s32 i = 0; | |
| while (i < AUTO_READ_DONE_TIMEOUT) { | |
| if (rd32(IGC_EECD) & IGC_EECD_AUTO_RD) | |
| break; | |
| usleep_range(1000, 2000); | |
| i++; | |
| } | |
| if (i == AUTO_READ_DONE_TIMEOUT) { | |
| hw_dbg("Auto read by HW from NVM has not completed.\n"); | |
| ret_val = -IGC_ERR_RESET; | |
| goto out; | |
| } | |
| out: | |
| return ret_val; | |
| } | |
| /** | |
| * igc_get_speed_and_duplex_copper - Retrieve current speed/duplex | |
| * @hw: pointer to the HW structure | |
| * @speed: stores the current speed | |
| * @duplex: stores the current duplex | |
| * | |
| * Read the status register for the current speed/duplex and store the current | |
| * speed and duplex for copper connections. | |
| */ | |
| s32 igc_get_speed_and_duplex_copper(struct igc_hw *hw, u16 *speed, | |
| u16 *duplex) | |
| { | |
| u32 status; | |
| status = rd32(IGC_STATUS); | |
| if (status & IGC_STATUS_SPEED_1000) { | |
| /* For I225, STATUS will indicate 1G speed in both 1 Gbps | |
| * and 2.5 Gbps link modes. An additional bit is used | |
| * to differentiate between 1 Gbps and 2.5 Gbps. | |
| */ | |
| if (hw->mac.type == igc_i225 && | |
| (status & IGC_STATUS_SPEED_2500)) { | |
| *speed = SPEED_2500; | |
| hw_dbg("2500 Mbs, "); | |
| } else { | |
| *speed = SPEED_1000; | |
| hw_dbg("1000 Mbs, "); | |
| } | |
| } else if (status & IGC_STATUS_SPEED_100) { | |
| *speed = SPEED_100; | |
| hw_dbg("100 Mbs, "); | |
| } else { | |
| *speed = SPEED_10; | |
| hw_dbg("10 Mbs, "); | |
| } | |
| if (status & IGC_STATUS_FD) { | |
| *duplex = FULL_DUPLEX; | |
| hw_dbg("Full Duplex\n"); | |
| } else { | |
| *duplex = HALF_DUPLEX; | |
| hw_dbg("Half Duplex\n"); | |
| } | |
| return 0; | |
| } | |
| /** | |
| * igc_put_hw_semaphore - Release hardware semaphore | |
| * @hw: pointer to the HW structure | |
| * | |
| * Release hardware semaphore used to access the PHY or NVM | |
| */ | |
| void igc_put_hw_semaphore(struct igc_hw *hw) | |
| { | |
| u32 swsm; | |
| swsm = rd32(IGC_SWSM); | |
| swsm &= ~(IGC_SWSM_SMBI | IGC_SWSM_SWESMBI); | |
| wr32(IGC_SWSM, swsm); | |
| } | |
| /** | |
| * igc_enable_mng_pass_thru - Enable processing of ARP's | |
| * @hw: pointer to the HW structure | |
| * | |
| * Verifies the hardware needs to leave interface enabled so that frames can | |
| * be directed to and from the management interface. | |
| */ | |
| bool igc_enable_mng_pass_thru(struct igc_hw *hw) | |
| { | |
| bool ret_val = false; | |
| u32 fwsm, factps; | |
| u32 manc; | |
| if (!hw->mac.asf_firmware_present) | |
| goto out; | |
| manc = rd32(IGC_MANC); | |
| if (!(manc & IGC_MANC_RCV_TCO_EN)) | |
| goto out; | |
| if (hw->mac.arc_subsystem_valid) { | |
| fwsm = rd32(IGC_FWSM); | |
| factps = rd32(IGC_FACTPS); | |
| if (!(factps & IGC_FACTPS_MNGCG) && | |
| ((fwsm & IGC_FWSM_MODE_MASK) == | |
| (igc_mng_mode_pt << IGC_FWSM_MODE_SHIFT))) { | |
| ret_val = true; | |
| goto out; | |
| } | |
| } else { | |
| if ((manc & IGC_MANC_SMBUS_EN) && | |
| !(manc & IGC_MANC_ASF_EN)) { | |
| ret_val = true; | |
| goto out; | |
| } | |
| } | |
| out: | |
| return ret_val; | |
| } | |
| /** | |
| * igc_hash_mc_addr - Generate a multicast hash value | |
| * @hw: pointer to the HW structure | |
| * @mc_addr: pointer to a multicast address | |
| * | |
| * Generates a multicast address hash value which is used to determine | |
| * the multicast filter table array address and new table value. See | |
| * igc_mta_set() | |
| **/ | |
| static u32 igc_hash_mc_addr(struct igc_hw *hw, u8 *mc_addr) | |
| { | |
| u32 hash_value, hash_mask; | |
| u8 bit_shift = 0; | |
| /* Register count multiplied by bits per register */ | |
| hash_mask = (hw->mac.mta_reg_count * 32) - 1; | |
| /* For a mc_filter_type of 0, bit_shift is the number of left-shifts | |
| * where 0xFF would still fall within the hash mask. | |
| */ | |
| while (hash_mask >> bit_shift != 0xFF) | |
| bit_shift++; | |
| /* The portion of the address that is used for the hash table | |
| * is determined by the mc_filter_type setting. | |
| * The algorithm is such that there is a total of 8 bits of shifting. | |
| * The bit_shift for a mc_filter_type of 0 represents the number of | |
| * left-shifts where the MSB of mc_addr[5] would still fall within | |
| * the hash_mask. Case 0 does this exactly. Since there are a total | |
| * of 8 bits of shifting, then mc_addr[4] will shift right the | |
| * remaining number of bits. Thus 8 - bit_shift. The rest of the | |
| * cases are a variation of this algorithm...essentially raising the | |
| * number of bits to shift mc_addr[5] left, while still keeping the | |
| * 8-bit shifting total. | |
| * | |
| * For example, given the following Destination MAC Address and an | |
| * MTA register count of 128 (thus a 4096-bit vector and 0xFFF mask), | |
| * we can see that the bit_shift for case 0 is 4. These are the hash | |
| * values resulting from each mc_filter_type... | |
| * [0] [1] [2] [3] [4] [5] | |
| * 01 AA 00 12 34 56 | |
| * LSB MSB | |
| * | |
| * case 0: hash_value = ((0x34 >> 4) | (0x56 << 4)) & 0xFFF = 0x563 | |
| * case 1: hash_value = ((0x34 >> 3) | (0x56 << 5)) & 0xFFF = 0xAC6 | |
| * case 2: hash_value = ((0x34 >> 2) | (0x56 << 6)) & 0xFFF = 0x163 | |
| * case 3: hash_value = ((0x34 >> 0) | (0x56 << 8)) & 0xFFF = 0x634 | |
| */ | |
| switch (hw->mac.mc_filter_type) { | |
| default: | |
| case 0: | |
| break; | |
| case 1: | |
| bit_shift += 1; | |
| break; | |
| case 2: | |
| bit_shift += 2; | |
| break; | |
| case 3: | |
| bit_shift += 4; | |
| break; | |
| } | |
| hash_value = hash_mask & (((mc_addr[4] >> (8 - bit_shift)) | | |
| (((u16)mc_addr[5]) << bit_shift))); | |
| return hash_value; | |
| } | |
| /** | |
| * igc_update_mc_addr_list - Update Multicast addresses | |
| * @hw: pointer to the HW structure | |
| * @mc_addr_list: array of multicast addresses to program | |
| * @mc_addr_count: number of multicast addresses to program | |
| * | |
| * Updates entire Multicast Table Array. | |
| * The caller must have a packed mc_addr_list of multicast addresses. | |
| **/ | |
| void igc_update_mc_addr_list(struct igc_hw *hw, | |
| u8 *mc_addr_list, u32 mc_addr_count) | |
| { | |
| u32 hash_value, hash_bit, hash_reg; | |
| int i; | |
| /* clear mta_shadow */ | |
| memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); | |
| /* update mta_shadow from mc_addr_list */ | |
| for (i = 0; (u32)i < mc_addr_count; i++) { | |
| hash_value = igc_hash_mc_addr(hw, mc_addr_list); | |
| hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); | |
| hash_bit = hash_value & 0x1F; | |
| hw->mac.mta_shadow[hash_reg] |= BIT(hash_bit); | |
| mc_addr_list += ETH_ALEN; | |
| } | |
| /* replace the entire MTA table */ | |
| for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) | |
| array_wr32(IGC_MTA, i, hw->mac.mta_shadow[i]); | |
| wrfl(); | |
| } |