arch/mips/Kconfig - u-boot - Git at Google


            
            menu "MIPS architecture"

            
            	depends on MIPS


            config SYS_ARCH

            
            	default "mips"


            config SYS_CPU

            
            	default "mips32" if CPU_MIPS32

            
            	default "mips64" if CPU_MIPS64


            choice

            
            	prompt "Target select"

            
            	optional


            config TARGET_MALTA

            
            	bool "Support malta"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select BOARD_EARLY_INIT_R

            
            	select DM

            
            	select DM_SERIAL

            
            	select PCI

            
            	select DYNAMIC_IO_PORT_BASE

            
            	select MIPS_CM

            
            	select MIPS_INSERT_BOOT_CONFIG

            
            	select SYS_CACHE_SHIFT_6

            
            	select MIPS_L2_CACHE

            
            	select OF_CONTROL

            
            	select OF_ISA_BUS

            
            	select PCI_MAP_SYSTEM_MEMORY

            
            	select ROM_EXCEPTION_VECTORS

            
            	select SUPPORTS_CPU_MIPS32_R1

            
            	select SUPPORTS_CPU_MIPS32_R2

            
            	select SUPPORTS_CPU_MIPS32_R6

            
            	select SUPPORTS_CPU_MIPS64_R1

            
            	select SUPPORTS_CPU_MIPS64_R2

            
            	select SUPPORTS_CPU_MIPS64_R6

            
            	select SUPPORT_BIG_ENDIAN

            
            	select SUPPORT_LITTLE_ENDIAN

            
            	select SWAP_IO_SPACE

            
            	imply CMD_DM


            config ARCH_ATH79

            
            	bool "Support QCA/Atheros ath79"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select DM

            
            	select OF_CONTROL

            
            	imply CMD_DM


            config ARCH_MSCC

            
            	bool "Support MSCC VCore-III"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select OF_CONTROL

            
            	select DM


            config ARCH_BMIPS

            
            	bool "Support BMIPS SoCs"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select CLK

            
            	select CPU

            
            	select DM

            
            	select OF_CONTROL

            
            	select RAM

            
            	select SYSRESET

            
            	imply CMD_DM


            config ARCH_MTMIPS

            
            	bool "Support MediaTek MIPS platforms"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select CLK

            
            	imply CMD_DM

            
            	select DISPLAY_CPUINFO

            
            	select DM

            
            	imply DM_GPIO

            
            	select DM_RESET

            
            	select DM_SERIAL

            
            	select PINCTRL

            
            	select PINMUX

            
            	select PINCONF

            
            	select RESET_MTMIPS

            
            	imply MTD

            
            	imply DM_SPI

            
            	imply DM_SPI_FLASH

            
            	select LAST_STAGE_INIT

            
            	select MIPS_TUNE_24KC

            
            	select OF_CONTROL

            
            	select ROM_EXCEPTION_VECTORS

            
            	select SUPPORTS_CPU_MIPS32_R1

            
            	select SUPPORTS_CPU_MIPS32_R2

            
            	select SUPPORT_LITTLE_ENDIAN

            
            	select SUPPORT_SPL


            config ARCH_JZ47XX

            
            	bool "Support Ingenic JZ47xx"

            
            	select SUPPORT_SPL

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select OF_CONTROL

            
            	select DM


            config ARCH_OCTEON

            
            	bool "Support Marvell Octeon CN7xxx platforms"

            
            	select ARCH_EARLY_INIT_R

            
            	select CPU_CAVIUM_OCTEON

            
            	select DISPLAY_CPUINFO

            
            	select DMA_ADDR_T_64BIT

            
            	select DM

            
            	select DM_GPIO

            
            	select DM_I2C

            
            	select DM_SERIAL

            
            	select DM_SPI

            
            	select MIPS_L2_CACHE

            
            	select MIPS_MACH_EARLY_INIT

            
            	select MIPS_TUNE_OCTEON3

            
            	select MTD

            
            	select ROM_EXCEPTION_VECTORS

            
            	select SUPPORT_BIG_ENDIAN

            
            	select SUPPORTS_CPU_MIPS64_OCTEON

            
            	select PHYS_64BIT

            
            	select OF_CONTROL

            
            	select OF_LIVE

            
            	imply CMD_DM


            config MACH_PIC32

            
            	bool "Support Microchip PIC32"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select DM

            
            	select DM_EVENT

            
            	select OF_CONTROL

            
            	imply CMD_DM


            config TARGET_BOSTON

            
            	bool "Support Boston"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select DM

            
            	select DM_SERIAL

            
            	select MIPS_CM

            
            	select SYS_CACHE_SHIFT_6

            
            	select MIPS_L2_CACHE

            
            	select OF_BOARD_SETUP

            
            	select OF_CONTROL

            
            	select ROM_EXCEPTION_VECTORS

            
            	select SUPPORTS_CPU_MIPS32_R1

            
            	select SUPPORTS_CPU_MIPS32_R2

            
            	select SUPPORTS_CPU_MIPS32_R6

            
            	select SUPPORTS_CPU_MIPS64_R1

            
            	select SUPPORTS_CPU_MIPS64_R2

            
            	select SUPPORTS_CPU_MIPS64_R6

            
            	select SUPPORT_BIG_ENDIAN

            
            	select SUPPORT_LITTLE_ENDIAN

            
            	imply CMD_DM


            config TARGET_XILFPGA

            
            	bool "Support Imagination Xilfpga"

            
            	select HAS_FIXED_TIMER_FREQUENCY

            
            	select DM

            
            	select DM_GPIO

            
            	select DM_SERIAL

            
            	select SYS_CACHE_SHIFT_4

            
            	select OF_CONTROL

            
            	select ROM_EXCEPTION_VECTORS

            
            	select SUPPORTS_CPU_MIPS32_R1

            
            	select SUPPORTS_CPU_MIPS32_R2

            
            	select SUPPORT_LITTLE_ENDIAN

            
            	imply CMD_DM

            
            	help

            
            	  This supports IMGTEC MIPSfpga platform


            endchoice


            source "board/imgtec/boston/Kconfig"

            
            source "board/imgtec/malta/Kconfig"

            
            source "board/imgtec/xilfpga/Kconfig"

            
            source "arch/mips/mach-ath79/Kconfig"

            
            source "arch/mips/mach-mscc/Kconfig"

            
            source "arch/mips/mach-bmips/Kconfig"

            
            source "arch/mips/mach-jz47xx/Kconfig"

            
            source "arch/mips/mach-pic32/Kconfig"

            
            source "arch/mips/mach-mtmips/Kconfig"

            
            source "arch/mips/mach-octeon/Kconfig"


            if MIPS


            choice

            
            	prompt "CPU selection"

            
            	default CPU_MIPS32_R2


            config CPU_MIPS32_R1

            
            	bool "MIPS32 Release 1"

            
            	depends on SUPPORTS_CPU_MIPS32_R1

            
            	select 32BIT

            
            	help

            
            	  Choose this option to build an U-Boot for release 1 through 5 of the

            
            	  MIPS32 architecture.


            config CPU_MIPS32_R2

            
            	bool "MIPS32 Release 2"

            
            	depends on SUPPORTS_CPU_MIPS32_R2

            
            	select 32BIT

            
            	help

            
            	  Choose this option to build an U-Boot for release 2 through 5 of the

            
            	  MIPS32 architecture.


            config CPU_MIPS32_R6

            
            	bool "MIPS32 Release 6"

            
            	depends on SUPPORTS_CPU_MIPS32_R6

            
            	select 32BIT

            
            	help

            
            	  Choose this option to build an U-Boot for release 6 or later of the

            
            	  MIPS32 architecture.


            config CPU_MIPS64_R1

            
            	bool "MIPS64 Release 1"

            
            	depends on SUPPORTS_CPU_MIPS64_R1

            
            	select 64BIT

            
            	help

            
            	  Choose this option to build a kernel for release 1 through 5 of the

            
            	  MIPS64 architecture.


            config CPU_MIPS64_R2

            
            	bool "MIPS64 Release 2"

            
            	depends on SUPPORTS_CPU_MIPS64_R2

            
            	select 64BIT

            
            	help

            
            	  Choose this option to build a kernel for release 2 through 5 of the

            
            	  MIPS64 architecture.


            config CPU_MIPS64_R6

            
            	bool "MIPS64 Release 6"

            
            	depends on SUPPORTS_CPU_MIPS64_R6

            
            	select 64BIT

            
            	help

            
            	  Choose this option to build a kernel for release 6 or later of the

            
            	  MIPS64 architecture.


            config CPU_MIPS64_OCTEON

            
            	bool "Marvell Octeon series of CPUs"

            
            	depends on SUPPORTS_CPU_MIPS64_OCTEON

            
            	select 64BIT

            
            	help

            
            	 Choose this option for Marvell Octeon CPUs.  These CPUs are between

            
            	 MIPS64 R5 and R6 with other extensions.


            endchoice


            menu "General setup"


            config ROM_EXCEPTION_VECTORS

            
            	bool "Build U-Boot image with exception vectors"

            
            	help

            
            	  Enable this to include exception vectors in the U-Boot image. This is

            
            	  required if the U-Boot entry point is equal to the address of the

            
            	  CPU reset exception vector (e.g. U-Boot as ROM loader in Qemu,

            
            	  U-Boot booted from parallel NOR flash).

            
            	  Disable this, if the U-Boot image is booted from DRAM (e.g. by SPL).

            
            	  In that case the image size will be reduced by 0x500 bytes.


            config SYS_MIPS_TIMER_FREQ

            
            	int "Fixed MIPS CPU timer frequency in Hz"

            
            	depends on HAS_FIXED_TIMER_FREQUENCY

            
            	help

            
            	  Configures a fixed CPU timer frequency.


            config MIPS_CM_BASE

            
            	hex "MIPS CM GCR Base Address"

            
            	depends on MIPS_CM

            
            	default 0x16100000 if TARGET_BOSTON

            
            	default 0x1fbf8000

            
            	help

            
            	  The physical base address at which to map the MIPS Coherence Manager

            
            	  Global Configuration Registers (GCRs). This should be set such that

            
            	  the GCRs occupy a region of the physical address space which is

            
            	  otherwise unused, or at minimum that software doesn't need to access.


            config MIPS_CACHE_INDEX_BASE

            
            	hex "Index base address for cache initialisation"

            
            	default 0x80000000 if CPU_MIPS32

            
            	default 0xffffffff80000000 if CPU_MIPS64

            
            	help

            
            	  This is the base address for a memory block, which is used for

            
            	  initialising the cache lines. This is also the base address of a memory

            
            	  block which is used for loading and filling cache lines when

            
            	  SYS_MIPS_CACHE_INIT_RAM_LOAD is selected.

            
            	  Normally this is CKSEG0. If the MIPS system needs to move this block

            
            	  to some SRAM or ScratchPad RAM, adapt this option accordingly.


            config MIPS_MACH_EARLY_INIT

            
            	bool "Enable mach specific very early init code"

            
            	help

            
            	  Use this to enable the call to mips_mach_early_init() very early

            
            	  from start.S. This function can be used e.g. to do some very early

            
            	  CPU / SoC intitialization or image copying. Its called very early

            
            	  and at this stage the PC might not match the linking address

            
            	  (CONFIG_TEXT_BASE) - no absolute jump done until this call.


            config MIPS_CACHE_SETUP

            
            	bool "Allow generic start code to initialize and setup caches"

            
            	default n if SKIP_LOWLEVEL_INIT

            
            	default y

            
            	help

            
            	  This allows the generic start code to invoke the generic initialization

            
            	  of the CPU caches. Disabling this can be useful for RAM boot scenarios

            
            	  (EJTAG, SPL payload) or for machines which don't need cache initialization

            
            	  or which want to provide their own cache implementation.


            	  If unsure, say yes.


            config MIPS_CACHE_DISABLE

            
            	bool "Allow generic start code to initially disable caches"

            
            	default n if SKIP_LOWLEVEL_INIT

            
            	default y

            
            	help

            
            	  This allows the generic start code to initially disable the CPU caches

            
            	  and run uncached until the caches are initialized and enabled. Disabling

            
            	  this can be useful on machines which don't need cache initialization or

            
            	  which want to provide their own cache implementation.


            	  If unsure, say yes.


            config MIPS_RELOCATION_TABLE_SIZE

            
            	hex "Relocation table size"

            
            	range 0x100 0x10000

            
            	default "0x8000"

            
            	---help---

            
            	  A table of relocation data will be appended to the U-Boot binary

            
            	  and parsed in relocate_code() to fix up all offsets in the relocated

            
            	  U-Boot.


            	  This option allows the amount of space reserved for the table to be

            
            	  adjusted in a range from 256 up to 64k. The default is 32k and should

            
            	  be ok in most cases. Reduce this value to shrink the size of U-Boot

            
            	  binary.


            	  The build will fail and a valid size suggested if this is too small.


            	  If unsure, leave at the default value.


            config RESTORE_EXCEPTION_VECTOR_BASE

            
            	bool "Restore exception vector base before booting linux kernel"

            
            	help

            
            	  In U-Boot the exception vector base will be moved to top of memory,

            
            	  to be used to display register dump when exception occurs.

            
            	  But some old linux kernel does not honor the base set in CP0_EBASE.

            
            	  A modified exception vector base will cause kernel crash.


            	  This option will restore the exception vector base to its previous

            
            	  value.


            	  If unsure, say N.


            config OVERRIDE_EXCEPTION_VECTOR_BASE

            
            	bool "Override the exception vector base to be restored"

            
            	depends on RESTORE_EXCEPTION_VECTOR_BASE

            
            	help

            
            	  Enable this option if you want to use a different exception vector

            
            	  base rather than the previously saved one.


            config NEW_EXCEPTION_VECTOR_BASE

            
            	hex "New exception vector base"

            
            	depends on OVERRIDE_EXCEPTION_VECTOR_BASE

            
            	range 0x80000000 0xbffff000

            
            	default 0x80000000

            
            	help

            
            	  The exception vector base to be restored before booting linux kernel


            config INIT_STACK_WITHOUT_MALLOC_F

            
            	bool "Do not reserve malloc space on initial stack"

            
            	help

            
            	  Enable this option if you don't want to reserve malloc space on

            
            	  initial stack. This is useful if the initial stack can't hold large

            
            	  malloc space. Platform should set the malloc_base later when DRAM is

            
            	  ready to use.


            config SPL_INIT_STACK_WITHOUT_MALLOC_F

            
            	bool "Do not reserve malloc space on initial stack in SPL"

            
            	help

            
            	  Enable this option if you don't want to reserve malloc space on

            
            	  initial stack. This is useful if the initial stack can't hold large

            
            	  malloc space. Platform should set the malloc_base later when DRAM is

            
            	  ready to use.


            config SPL_LOADER_SUPPORT

            
            	bool

            
            	help

            
            	  Enable this option if you want to use SPL loaders without DM enabled.


            endmenu


            menu "OS boot interface"


            config MIPS_BOOT_CMDLINE_LEGACY

            
            	bool "Hand over legacy command line to Linux kernel"

            
            	default y

            
            	help

            
            	  Enable this option if you want U-Boot to hand over the Yamon-style

            
            	  command line to the kernel. All bootargs will be prepared as argc/argv

            
            	  compatible list. The argument count (argc) is stored in register $a0.

            
            	  The address of the argument list (argv) is stored in register $a1.


            config MIPS_BOOT_ENV_LEGACY

            
            	bool "Hand over legacy environment to Linux kernel"

            
            	default y

            
            	help

            
            	  Enable this option if you want U-Boot to hand over the Yamon-style

            
            	  environment to the kernel. Information like memory size, initrd

            
            	  address and size will be prepared as zero-terminated key/value list.

            
            	  The address of the environment is stored in register $a2.


            config MIPS_BOOT_FDT

            
            	bool "Hand over a flattened device tree to Linux kernel"

            
            	help

            
            	  Enable this option if you want U-Boot to hand over a flattened

            
            	  device tree to the kernel. According to UHI register $a0 will be set

            
            	  to -2 and the FDT address is stored in $a1.


            endmenu


            config SUPPORTS_CPU_MIPS32_R1

            
            	bool


            config SUPPORTS_CPU_MIPS32_R2

            
            	bool


            config SUPPORTS_CPU_MIPS32_R6

            
            	bool


            config SUPPORTS_CPU_MIPS64_R1

            
            	bool


            config SUPPORTS_CPU_MIPS64_R2

            
            	bool


            config SUPPORTS_CPU_MIPS64_R6

            
            	bool


            config SUPPORTS_CPU_MIPS64_OCTEON

            
            	bool


            config HAS_FIXED_TIMER_FREQUENCY

            
            	bool


            config CPU_CAVIUM_OCTEON

            
            	bool


            config CPU_MIPS32

            
            	bool

            
            	default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R6


            config CPU_MIPS64

            
            	bool

            
            	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R6

            
            	default y if CPU_MIPS64_OCTEON


            config MIPS_TUNE_4KC

            
            	bool


            config MIPS_TUNE_14KC

            
            	bool


            config MIPS_TUNE_24KC

            
            	bool


            config MIPS_TUNE_34KC

            
            	bool


            config MIPS_TUNE_74KC

            
            	bool


            config MIPS_TUNE_OCTEON3

            
            	bool


            config SWAP_IO_SPACE

            
            	bool


            config SYS_MIPS_CACHE_INIT_RAM_LOAD

            
            	bool


            config MIPS_INIT_STACK_IN_SRAM

            
            	bool

            
            	help

            
            	  Select this if the initial stack frame could be setup in SRAM.

            
            	  Normally the initial stack frame is set up in DRAM which is often

            
            	  only available after lowlevel_init. With this option the initial

            
            	  stack frame and the early C environment is set up before

            
            	  lowlevel_init. Thus lowlevel_init does not need to be implemented

            
            	  in assembler.


            config MIPS_SRAM_INIT

            
            	bool

            
            	depends on MIPS_INIT_STACK_IN_SRAM

            
            	help

            
            	  Select this if the SRAM for initial stack needs to be initialized

            
            	  before it can be used. If enabled, a function mips_sram_init() will

            
            	  be called just before setup_stack_gd.


            config DMA_ADDR_T_64BIT

            
            	bool

            
            	help

            
            	 Select this to enable 64-bit DMA addressing


            config SYS_DCACHE_SIZE

            
            	int

            
            	default 0

            
            	help

            
            	  The total size of the L1 Dcache, if known at compile time.


            config SYS_DCACHE_LINE_SIZE

            
            	int

            
            	default 0

            
            	help

            
            	  The size of L1 Dcache lines, if known at compile time.


            config SYS_ICACHE_SIZE

            
            	int

            
            	default 0

            
            	help

            
            	  The total size of the L1 ICache, if known at compile time.


            config SYS_ICACHE_LINE_SIZE

            
            	int

            
            	default 0

            
            	help

            
            	  The size of L1 Icache lines, if known at compile time.


            config SYS_SCACHE_LINE_SIZE

            
            	int

            
            	default 0

            
            	help

            
            	  The size of L2 cache lines, if known at compile time.


            config SYS_CACHE_SIZE_AUTO

            
            	def_bool y if SYS_DCACHE_SIZE = 0 && SYS_ICACHE_SIZE = 0 && \

            
            		SYS_DCACHE_LINE_SIZE = 0 && SYS_ICACHE_LINE_SIZE = 0 && \

            
            		SYS_SCACHE_LINE_SIZE = 0

            
            	help

            
            	  Select this (or let it be auto-selected by not defining any cache

            
            	  sizes) in order to allow U-Boot to automatically detect the sizes

            
            	  of caches at runtime. This has a small cost in code size & runtime

            
            	  so if you know the cache configuration for your system at compile

            
            	  time it would be beneficial to configure it.


            config MIPS_L2_CACHE

            
            	bool

            
            	help

            
            	  Select this if your system includes an L2 cache and you want U-Boot

            
            	  to initialise & maintain it.


            config DYNAMIC_IO_PORT_BASE

            
            	bool


            config MIPS_CM

            
            	bool

            
            	help

            
            	  Select this if your system contains a MIPS Coherence Manager and you

            
            	  wish U-Boot to configure it or make use of it to retrieve system

            
            	  information such as cache configuration.


            config MIPS_INSERT_BOOT_CONFIG

            
            	bool

            
            	help

            
            	  Enable this to insert some board-specific boot configuration in

            
            	  the U-Boot binary at offset 0x10.


            config MIPS_BOOT_CONFIG_WORD0

            
            	hex

            
            	depends on MIPS_INSERT_BOOT_CONFIG

            
            	default 0x420 if TARGET_MALTA

            
            	default 0x0

            
            	help

            
            	  Value which is inserted as boot config word 0.


            config MIPS_BOOT_CONFIG_WORD1

            
            	hex

            
            	depends on MIPS_INSERT_BOOT_CONFIG

            
            	default 0x0

            
            	help

            
            	  Value which is inserted as boot config word 1.


            endif


            endmenu
	menu "MIPS architecture"
	depends on MIPS

	config SYS_ARCH
	default "mips"

	config SYS_CPU
	default "mips32" if CPU_MIPS32
	default "mips64" if CPU_MIPS64

	choice
	prompt "Target select"
	optional

	config TARGET_MALTA
	bool "Support malta"
	select HAS_FIXED_TIMER_FREQUENCY
	select BOARD_EARLY_INIT_R
	select DM
	select DM_SERIAL
	select PCI
	select DYNAMIC_IO_PORT_BASE
	select MIPS_CM
	select MIPS_INSERT_BOOT_CONFIG
	select SYS_CACHE_SHIFT_6
	select MIPS_L2_CACHE
	select OF_CONTROL
	select OF_ISA_BUS
	select PCI_MAP_SYSTEM_MEMORY
	select ROM_EXCEPTION_VECTORS
	select SUPPORTS_CPU_MIPS32_R1
	select SUPPORTS_CPU_MIPS32_R2
	select SUPPORTS_CPU_MIPS32_R6
	select SUPPORTS_CPU_MIPS64_R1
	select SUPPORTS_CPU_MIPS64_R2
	select SUPPORTS_CPU_MIPS64_R6
	select SUPPORT_BIG_ENDIAN
	select SUPPORT_LITTLE_ENDIAN
	select SWAP_IO_SPACE
	imply CMD_DM

	config ARCH_ATH79
	bool "Support QCA/Atheros ath79"
	select HAS_FIXED_TIMER_FREQUENCY
	select DM
	select OF_CONTROL
	imply CMD_DM

	config ARCH_MSCC
	bool "Support MSCC VCore-III"
	select HAS_FIXED_TIMER_FREQUENCY
	select OF_CONTROL
	select DM

	config ARCH_BMIPS
	bool "Support BMIPS SoCs"
	select HAS_FIXED_TIMER_FREQUENCY
	select CLK
	select CPU
	select DM
	select OF_CONTROL
	select RAM
	select SYSRESET
	imply CMD_DM

	config ARCH_MTMIPS
	bool "Support MediaTek MIPS platforms"
	select HAS_FIXED_TIMER_FREQUENCY
	select CLK
	imply CMD_DM
	select DISPLAY_CPUINFO
	select DM
	imply DM_GPIO
	select DM_RESET
	select DM_SERIAL
	select PINCTRL
	select PINMUX
	select PINCONF
	select RESET_MTMIPS
	imply MTD
	imply DM_SPI
	imply DM_SPI_FLASH
	select LAST_STAGE_INIT
	select MIPS_TUNE_24KC
	select OF_CONTROL
	select ROM_EXCEPTION_VECTORS
	select SUPPORTS_CPU_MIPS32_R1
	select SUPPORTS_CPU_MIPS32_R2
	select SUPPORT_LITTLE_ENDIAN
	select SUPPORT_SPL

	config ARCH_JZ47XX
	bool "Support Ingenic JZ47xx"
	select SUPPORT_SPL
	select HAS_FIXED_TIMER_FREQUENCY
	select OF_CONTROL
	select DM

	config ARCH_OCTEON
	bool "Support Marvell Octeon CN7xxx platforms"
	select ARCH_EARLY_INIT_R
	select CPU_CAVIUM_OCTEON
	select DISPLAY_CPUINFO
	select DMA_ADDR_T_64BIT
	select DM
	select DM_GPIO
	select DM_I2C
	select DM_SERIAL
	select DM_SPI
	select MIPS_L2_CACHE
	select MIPS_MACH_EARLY_INIT
	select MIPS_TUNE_OCTEON3
	select MTD
	select ROM_EXCEPTION_VECTORS
	select SUPPORT_BIG_ENDIAN
	select SUPPORTS_CPU_MIPS64_OCTEON
	select PHYS_64BIT
	select OF_CONTROL
	select OF_LIVE
	imply CMD_DM

	config MACH_PIC32
	bool "Support Microchip PIC32"
	select HAS_FIXED_TIMER_FREQUENCY
	select DM
	select DM_EVENT
	select OF_CONTROL
	imply CMD_DM

	config TARGET_BOSTON
	bool "Support Boston"
	select HAS_FIXED_TIMER_FREQUENCY
	select DM
	select DM_SERIAL
	select MIPS_CM
	select SYS_CACHE_SHIFT_6
	select MIPS_L2_CACHE
	select OF_BOARD_SETUP
	select OF_CONTROL
	select ROM_EXCEPTION_VECTORS
	select SUPPORTS_CPU_MIPS32_R1
	select SUPPORTS_CPU_MIPS32_R2
	select SUPPORTS_CPU_MIPS32_R6
	select SUPPORTS_CPU_MIPS64_R1
	select SUPPORTS_CPU_MIPS64_R2
	select SUPPORTS_CPU_MIPS64_R6
	select SUPPORT_BIG_ENDIAN
	select SUPPORT_LITTLE_ENDIAN
	imply CMD_DM

	config TARGET_XILFPGA
	bool "Support Imagination Xilfpga"
	select HAS_FIXED_TIMER_FREQUENCY
	select DM
	select DM_GPIO
	select DM_SERIAL
	select SYS_CACHE_SHIFT_4
	select OF_CONTROL
	select ROM_EXCEPTION_VECTORS
	select SUPPORTS_CPU_MIPS32_R1
	select SUPPORTS_CPU_MIPS32_R2
	select SUPPORT_LITTLE_ENDIAN
	imply CMD_DM
	help
	This supports IMGTEC MIPSfpga platform

	endchoice

	source "board/imgtec/boston/Kconfig"
	source "board/imgtec/malta/Kconfig"
	source "board/imgtec/xilfpga/Kconfig"
	source "arch/mips/mach-ath79/Kconfig"
	source "arch/mips/mach-mscc/Kconfig"
	source "arch/mips/mach-bmips/Kconfig"
	source "arch/mips/mach-jz47xx/Kconfig"
	source "arch/mips/mach-pic32/Kconfig"
	source "arch/mips/mach-mtmips/Kconfig"
	source "arch/mips/mach-octeon/Kconfig"

	if MIPS

	choice
	prompt "CPU selection"
	default CPU_MIPS32_R2

	config CPU_MIPS32_R1
	bool "MIPS32 Release 1"
	depends on SUPPORTS_CPU_MIPS32_R1
	select 32BIT
	help
	Choose this option to build an U-Boot for release 1 through 5 of the
	MIPS32 architecture.

	config CPU_MIPS32_R2
	bool "MIPS32 Release 2"
	depends on SUPPORTS_CPU_MIPS32_R2
	select 32BIT
	help
	Choose this option to build an U-Boot for release 2 through 5 of the
	MIPS32 architecture.

	config CPU_MIPS32_R6
	bool "MIPS32 Release 6"
	depends on SUPPORTS_CPU_MIPS32_R6
	select 32BIT
	help
	Choose this option to build an U-Boot for release 6 or later of the
	MIPS32 architecture.

	config CPU_MIPS64_R1
	bool "MIPS64 Release 1"
	depends on SUPPORTS_CPU_MIPS64_R1
	select 64BIT
	help
	Choose this option to build a kernel for release 1 through 5 of the
	MIPS64 architecture.

	config CPU_MIPS64_R2
	bool "MIPS64 Release 2"
	depends on SUPPORTS_CPU_MIPS64_R2
	select 64BIT
	help
	Choose this option to build a kernel for release 2 through 5 of the
	MIPS64 architecture.

	config CPU_MIPS64_R6
	bool "MIPS64 Release 6"
	depends on SUPPORTS_CPU_MIPS64_R6
	select 64BIT
	help
	Choose this option to build a kernel for release 6 or later of the
	MIPS64 architecture.

	config CPU_MIPS64_OCTEON
	bool "Marvell Octeon series of CPUs"
	depends on SUPPORTS_CPU_MIPS64_OCTEON
	select 64BIT
	help
	Choose this option for Marvell Octeon CPUs. These CPUs are between
	MIPS64 R5 and R6 with other extensions.

	endchoice

	menu "General setup"

	config ROM_EXCEPTION_VECTORS
	bool "Build U-Boot image with exception vectors"
	help
	Enable this to include exception vectors in the U-Boot image. This is
	required if the U-Boot entry point is equal to the address of the
	CPU reset exception vector (e.g. U-Boot as ROM loader in Qemu,
	U-Boot booted from parallel NOR flash).
	Disable this, if the U-Boot image is booted from DRAM (e.g. by SPL).
	In that case the image size will be reduced by 0x500 bytes.

	config SYS_MIPS_TIMER_FREQ
	int "Fixed MIPS CPU timer frequency in Hz"
	depends on HAS_FIXED_TIMER_FREQUENCY
	help
	Configures a fixed CPU timer frequency.

	config MIPS_CM_BASE
	hex "MIPS CM GCR Base Address"
	depends on MIPS_CM
	default 0x16100000 if TARGET_BOSTON
	default 0x1fbf8000
	help
	The physical base address at which to map the MIPS Coherence Manager
	Global Configuration Registers (GCRs). This should be set such that
	the GCRs occupy a region of the physical address space which is
	otherwise unused, or at minimum that software doesn't need to access.

	config MIPS_CACHE_INDEX_BASE
	hex "Index base address for cache initialisation"
	default 0x80000000 if CPU_MIPS32
	default 0xffffffff80000000 if CPU_MIPS64
	help
	This is the base address for a memory block, which is used for
	initialising the cache lines. This is also the base address of a memory
	block which is used for loading and filling cache lines when
	SYS_MIPS_CACHE_INIT_RAM_LOAD is selected.
	Normally this is CKSEG0. If the MIPS system needs to move this block
	to some SRAM or ScratchPad RAM, adapt this option accordingly.

	config MIPS_MACH_EARLY_INIT
	bool "Enable mach specific very early init code"
	help
	Use this to enable the call to mips_mach_early_init() very early
	from start.S. This function can be used e.g. to do some very early
	CPU / SoC intitialization or image copying. Its called very early
	and at this stage the PC might not match the linking address
	(CONFIG_TEXT_BASE) - no absolute jump done until this call.

	config MIPS_CACHE_SETUP
	bool "Allow generic start code to initialize and setup caches"
	default n if SKIP_LOWLEVEL_INIT
	default y
	help
	This allows the generic start code to invoke the generic initialization
	of the CPU caches. Disabling this can be useful for RAM boot scenarios
	(EJTAG, SPL payload) or for machines which don't need cache initialization
	or which want to provide their own cache implementation.

	If unsure, say yes.

	config MIPS_CACHE_DISABLE
	bool "Allow generic start code to initially disable caches"
	default n if SKIP_LOWLEVEL_INIT
	default y
	help
	This allows the generic start code to initially disable the CPU caches
	and run uncached until the caches are initialized and enabled. Disabling
	this can be useful on machines which don't need cache initialization or
	which want to provide their own cache implementation.

	If unsure, say yes.

	config MIPS_RELOCATION_TABLE_SIZE
	hex "Relocation table size"
	range 0x100 0x10000
	default "0x8000"
	---help---
	A table of relocation data will be appended to the U-Boot binary
	and parsed in relocate_code() to fix up all offsets in the relocated
	U-Boot.

	This option allows the amount of space reserved for the table to be
	adjusted in a range from 256 up to 64k. The default is 32k and should
	be ok in most cases. Reduce this value to shrink the size of U-Boot
	binary.

	The build will fail and a valid size suggested if this is too small.

	If unsure, leave at the default value.

	config RESTORE_EXCEPTION_VECTOR_BASE
	bool "Restore exception vector base before booting linux kernel"
	help
	In U-Boot the exception vector base will be moved to top of memory,
	to be used to display register dump when exception occurs.
	But some old linux kernel does not honor the base set in CP0_EBASE.
	A modified exception vector base will cause kernel crash.

	This option will restore the exception vector base to its previous
	value.

	If unsure, say N.

	config OVERRIDE_EXCEPTION_VECTOR_BASE
	bool "Override the exception vector base to be restored"
	depends on RESTORE_EXCEPTION_VECTOR_BASE
	help
	Enable this option if you want to use a different exception vector
	base rather than the previously saved one.

	config NEW_EXCEPTION_VECTOR_BASE
	hex "New exception vector base"
	depends on OVERRIDE_EXCEPTION_VECTOR_BASE
	range 0x80000000 0xbffff000
	default 0x80000000
	help
	The exception vector base to be restored before booting linux kernel

	config INIT_STACK_WITHOUT_MALLOC_F
	bool "Do not reserve malloc space on initial stack"
	help
	Enable this option if you don't want to reserve malloc space on
	initial stack. This is useful if the initial stack can't hold large
	malloc space. Platform should set the malloc_base later when DRAM is
	ready to use.

	config SPL_INIT_STACK_WITHOUT_MALLOC_F
	bool "Do not reserve malloc space on initial stack in SPL"
	help
	Enable this option if you don't want to reserve malloc space on
	initial stack. This is useful if the initial stack can't hold large
	malloc space. Platform should set the malloc_base later when DRAM is
	ready to use.

	config SPL_LOADER_SUPPORT
	bool
	help
	Enable this option if you want to use SPL loaders without DM enabled.

	endmenu

	menu "OS boot interface"

	config MIPS_BOOT_CMDLINE_LEGACY
	bool "Hand over legacy command line to Linux kernel"
	default y
	help
	Enable this option if you want U-Boot to hand over the Yamon-style
	command line to the kernel. All bootargs will be prepared as argc/argv
	compatible list. The argument count (argc) is stored in register $a0.
	The address of the argument list (argv) is stored in register $a1.

	config MIPS_BOOT_ENV_LEGACY
	bool "Hand over legacy environment to Linux kernel"
	default y
	help
	Enable this option if you want U-Boot to hand over the Yamon-style
	environment to the kernel. Information like memory size, initrd
	address and size will be prepared as zero-terminated key/value list.
	The address of the environment is stored in register $a2.

	config MIPS_BOOT_FDT
	bool "Hand over a flattened device tree to Linux kernel"
	help
	Enable this option if you want U-Boot to hand over a flattened
	device tree to the kernel. According to UHI register $a0 will be set
	to -2 and the FDT address is stored in $a1.

	endmenu

	config SUPPORTS_CPU_MIPS32_R1
	bool

	config SUPPORTS_CPU_MIPS32_R2
	bool

	config SUPPORTS_CPU_MIPS32_R6
	bool

	config SUPPORTS_CPU_MIPS64_R1
	bool

	config SUPPORTS_CPU_MIPS64_R2
	bool

	config SUPPORTS_CPU_MIPS64_R6
	bool

	config SUPPORTS_CPU_MIPS64_OCTEON
	bool

	config HAS_FIXED_TIMER_FREQUENCY
	bool

	config CPU_CAVIUM_OCTEON
	bool

	config CPU_MIPS32
	bool
	default y if CPU_MIPS32_R1 \|\| CPU_MIPS32_R2 \|\| CPU_MIPS32_R6

	config CPU_MIPS64
	bool
	default y if CPU_MIPS64_R1 \|\| CPU_MIPS64_R2 \|\| CPU_MIPS64_R6
	default y if CPU_MIPS64_OCTEON

	config MIPS_TUNE_4KC
	bool

	config MIPS_TUNE_14KC
	bool

	config MIPS_TUNE_24KC
	bool

	config MIPS_TUNE_34KC
	bool

	config MIPS_TUNE_74KC
	bool

	config MIPS_TUNE_OCTEON3
	bool

	config SWAP_IO_SPACE
	bool

	config SYS_MIPS_CACHE_INIT_RAM_LOAD
	bool

	config MIPS_INIT_STACK_IN_SRAM
	bool
	help
	Select this if the initial stack frame could be setup in SRAM.
	Normally the initial stack frame is set up in DRAM which is often
	only available after lowlevel_init. With this option the initial
	stack frame and the early C environment is set up before
	lowlevel_init. Thus lowlevel_init does not need to be implemented
	in assembler.

	config MIPS_SRAM_INIT
	bool
	depends on MIPS_INIT_STACK_IN_SRAM
	help
	Select this if the SRAM for initial stack needs to be initialized
	before it can be used. If enabled, a function mips_sram_init() will
	be called just before setup_stack_gd.

	config DMA_ADDR_T_64BIT
	bool
	help
	Select this to enable 64-bit DMA addressing

	config SYS_DCACHE_SIZE
	int
	default 0
	help
	The total size of the L1 Dcache, if known at compile time.

	config SYS_DCACHE_LINE_SIZE
	int
	default 0
	help
	The size of L1 Dcache lines, if known at compile time.

	config SYS_ICACHE_SIZE
	int
	default 0
	help
	The total size of the L1 ICache, if known at compile time.

	config SYS_ICACHE_LINE_SIZE
	int
	default 0
	help
	The size of L1 Icache lines, if known at compile time.

	config SYS_SCACHE_LINE_SIZE
	int
	default 0
	help
	The size of L2 cache lines, if known at compile time.


	config SYS_CACHE_SIZE_AUTO
	def_bool y if SYS_DCACHE_SIZE = 0 && SYS_ICACHE_SIZE = 0 && \
	SYS_DCACHE_LINE_SIZE = 0 && SYS_ICACHE_LINE_SIZE = 0 && \
	SYS_SCACHE_LINE_SIZE = 0
	help
	Select this (or let it be auto-selected by not defining any cache
	sizes) in order to allow U-Boot to automatically detect the sizes
	of caches at runtime. This has a small cost in code size & runtime
	so if you know the cache configuration for your system at compile
	time it would be beneficial to configure it.

	config MIPS_L2_CACHE
	bool
	help
	Select this if your system includes an L2 cache and you want U-Boot
	to initialise & maintain it.

	config DYNAMIC_IO_PORT_BASE
	bool

	config MIPS_CM
	bool
	help
	Select this if your system contains a MIPS Coherence Manager and you
	wish U-Boot to configure it or make use of it to retrieve system
	information such as cache configuration.

	config MIPS_INSERT_BOOT_CONFIG
	bool
	help
	Enable this to insert some board-specific boot configuration in
	the U-Boot binary at offset 0x10.

	config MIPS_BOOT_CONFIG_WORD0
	hex
	depends on MIPS_INSERT_BOOT_CONFIG
	default 0x420 if TARGET_MALTA
	default 0x0
	help
	Value which is inserted as boot config word 0.

	config MIPS_BOOT_CONFIG_WORD1
	hex
	depends on MIPS_INSERT_BOOT_CONFIG
	default 0x0
	help
	Value which is inserted as boot config word 1.

	endif

	endmenu