| CONFIG_ARM=y | |
| CONFIG_SKIP_LOWLEVEL_INIT_ONLY=y | |
| CONFIG_SPL_SKIP_LOWLEVEL_INIT_ONLY=y | |
| # CONFIG_SPL_USE_ARCH_MEMCPY is not set | |
| # CONFIG_SPL_USE_ARCH_MEMSET is not set | |
| CONFIG_ARCH_AT91=y | |
| CONFIG_TEXT_BASE=0x72000000 | |
| CONFIG_SYS_MALLOC_LEN=0x460000 | |
| CONFIG_SYS_MALLOC_F_LEN=0x800 | |
| CONFIG_TARGET_CORVUS=y | |
| CONFIG_AT91_GPIO_PULLUP=y | |
| CONFIG_ATMEL_LEGACY=y | |
| CONFIG_SPL_GPIO=y | |
| CONFIG_SPL_LIBCOMMON_SUPPORT=y | |
| CONFIG_SPL_LIBGENERIC_SUPPORT=y | |
| CONFIG_NR_DRAM_BANKS=1 | |
| CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y | |
| CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x70007f00 | |
| CONFIG_ENV_OFFSET=0x100000 | |
| CONFIG_DEFAULT_DEVICE_TREE="at91sam9g45-corvus" | |
| CONFIG_SPL_TEXT_BASE=0x300000 | |
| CONFIG_SPL_SERIAL=y | |
| CONFIG_SPL_STACK=0x4000 | |
| CONFIG_SPL_HAS_BSS_LINKER_SECTION=y | |
| CONFIG_SPL_BSS_START_ADDR=0x3000 | |
| CONFIG_SPL_BSS_MAX_SIZE=0x800 | |
| CONFIG_SPL=y | |
| CONFIG_ENV_OFFSET_REDUND=0x180000 | |
| CONFIG_SYS_LOAD_ADDR=0x70000000 | |
| CONFIG_NAND_BOOT=y | |
| CONFIG_BOOTDELAY=3 | |
| CONFIG_USE_BOOTARGS=y | |
| CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2" | |
| CONFIG_USE_BOOTCOMMAND=y | |
| CONFIG_BOOTCOMMAND="nand read 0x70000000 0x200000 0x300000;bootm 0x70000000" | |
| CONFIG_SYS_CBSIZE=256 | |
| CONFIG_SYS_PBSIZE=281 | |
| # CONFIG_DISPLAY_BOARDINFO is not set | |
| CONFIG_BOARD_EARLY_INIT_F=y | |
| CONFIG_SPL_MAX_SIZE=0x3000 | |
| CONFIG_SPL_PAD_TO=0x20000 | |
| CONFIG_SPL_SYS_MALLOC_SIMPLE=y | |
| # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set | |
| CONFIG_SPL_NAND_SUPPORT=y | |
| CONFIG_SPL_NAND_RAW_ONLY=y | |
| CONFIG_SPL_NAND_DRIVERS=y | |
| CONFIG_SPL_NAND_ECC=y | |
| CONFIG_SPL_NAND_SOFTECC=y | |
| CONFIG_SPL_NAND_BASE=y | |
| CONFIG_HUSH_PARSER=y | |
| CONFIG_SYS_PROMPT="U-Boot> " | |
| # CONFIG_CMD_BDI is not set | |
| CONFIG_CMD_BOOTZ=y | |
| # CONFIG_CMD_IMI is not set | |
| CONFIG_CMD_DFU=y | |
| CONFIG_CMD_GPIO=y | |
| # CONFIG_CMD_LOADS is not set | |
| CONFIG_CMD_NAND=y | |
| CONFIG_CMD_USB=y | |
| # CONFIG_CMD_SOURCE is not set | |
| # CONFIG_CMD_SETEXPR is not set | |
| CONFIG_CMD_DHCP=y | |
| CONFIG_BOOTP_BOOTFILESIZE=y | |
| CONFIG_CMD_PING=y | |
| CONFIG_CMD_MTDPARTS=y | |
| CONFIG_DOS_PARTITION=y | |
| CONFIG_OF_CONTROL=y | |
| CONFIG_ENV_IS_IN_NAND=y | |
| CONFIG_SYS_REDUNDAND_ENVIRONMENT=y | |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y | |
| CONFIG_NET_RETRY_COUNT=20 | |
| CONFIG_CLK=y | |
| CONFIG_CLK_AT91=y | |
| CONFIG_DFU_NAND=y | |
| CONFIG_SYS_DFU_DATA_BUF_SIZE=0x100000 | |
| CONFIG_AT91_GPIO=y | |
| # CONFIG_MMC is not set | |
| CONFIG_MTD=y | |
| CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT=y | |
| # CONFIG_SYS_NAND_USE_FLASH_BBT is not set | |
| CONFIG_NAND_ATMEL=y | |
| CONFIG_SYS_NAND_BLOCK_SIZE=0x20000 | |
| CONFIG_SYS_NAND_PAGE_SIZE=0x800 | |
| CONFIG_SYS_NAND_OOBSIZE=0x40 | |
| CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y | |
| CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000 | |
| CONFIG_MACB=y | |
| CONFIG_RMII=y | |
| CONFIG_ATMEL_USART=y | |
| CONFIG_USB=y | |
| CONFIG_USB_EHCI_HCD=y | |
| CONFIG_USB_GADGET=y | |
| CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" | |
| CONFIG_USB_GADGET_VENDOR_NUM=0x0908 | |
| CONFIG_USB_GADGET_PRODUCT_NUM=0x02d2 | |
| CONFIG_USB_GADGET_ATMEL_USBA=y | |
| CONFIG_USB_GADGET_DOWNLOAD=y |