| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) | |
| /* | |
| * sama7g5.dtsi - Device Tree Include file for SAMA7G5 family SoC | |
| * | |
| * Copyright (C) 2020 Microchip Technology, Inc. and its subsidiaries | |
| * | |
| * Author: Eugen Hristev <eugen.hristev@microchip.com> | |
| * Author: Claudiu Beznea <claudiu.beznea@microchip.com> | |
| * | |
| */ | |
| #include <dt-bindings/iio/adc/at91-sama5d2_adc.h> | |
| #include <dt-bindings/interrupt-controller/irq.h> | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> | |
| #include <dt-bindings/clock/at91.h> | |
| #include <dt-bindings/dma/at91.h> | |
| #include <dt-bindings/gpio/gpio.h> | |
| #include <dt-bindings/mfd/at91-usart.h> | |
| #include <dt-bindings/nvmem/microchip,sama7g5-otpc.h> | |
| #include <dt-bindings/thermal/thermal.h> | |
| / { | |
| model = "Microchip SAMA7G5 family SoC"; | |
| compatible = "microchip,sama7g5"; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| interrupt-parent = <&gic>; | |
| cpus { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| cpu0: cpu@0 { | |
| device_type = "cpu"; | |
| compatible = "arm,cortex-a7"; | |
| reg = <0x0>; | |
| clocks = <&pmc PMC_TYPE_CORE PMC_CPUPLL>; | |
| clock-names = "cpu"; | |
| operating-points-v2 = <&cpu_opp_table>; | |
| #cooling-cells = <2>; /* min followed by max */ | |
| }; | |
| }; | |
| cpu_opp_table: opp-table { | |
| compatible = "operating-points-v2"; | |
| opp-90000000 { | |
| opp-hz = /bits/ 64 <90000000>; | |
| opp-microvolt = <1050000 1050000 1225000>; | |
| clock-latency-ns = <320000>; | |
| }; | |
| opp-250000000 { | |
| opp-hz = /bits/ 64 <250000000>; | |
| opp-microvolt = <1050000 1050000 1225000>; | |
| clock-latency-ns = <320000>; | |
| }; | |
| opp-600000000 { | |
| opp-hz = /bits/ 64 <600000000>; | |
| opp-microvolt = <1050000 1050000 1225000>; | |
| clock-latency-ns = <320000>; | |
| opp-suspend; | |
| }; | |
| opp-800000000 { | |
| opp-hz = /bits/ 64 <800000000>; | |
| opp-microvolt = <1150000 1125000 1225000>; | |
| clock-latency-ns = <320000>; | |
| }; | |
| opp-1000000002 { | |
| opp-hz = /bits/ 64 <1000000002>; | |
| opp-microvolt = <1250000 1225000 1300000>; | |
| clock-latency-ns = <320000>; | |
| }; | |
| }; | |
| thermal-zones { | |
| cpu_thermal: cpu-thermal { | |
| polling-delay-passive = <1000>; | |
| polling-delay = <5000>; | |
| thermal-sensors = <&thermal_sensor>; | |
| trips { | |
| cpu_normal: cpu-alert0 { | |
| temperature = <90000>; | |
| hysteresis = <0>; | |
| type = "passive"; | |
| }; | |
| cpu_hot: cpu-alert1 { | |
| temperature = <95000>; | |
| hysteresis = <0>; | |
| type = "passive"; | |
| }; | |
| cpu_critical: cpu-critical { | |
| temperature = <100000>; | |
| hysteresis = <0>; | |
| type = "critical"; | |
| }; | |
| }; | |
| cooling-maps { | |
| map0 { | |
| trip = <&cpu_normal>; | |
| cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; | |
| }; | |
| map1 { | |
| trip = <&cpu_hot>; | |
| cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| clocks { | |
| slow_xtal: slow_xtal { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| }; | |
| main_xtal: main_xtal { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| }; | |
| usb_clk: usb_clk { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <48000000>; | |
| }; | |
| }; | |
| vddout25: fixed-regulator-vddout25 { | |
| compatible = "regulator-fixed"; | |
| regulator-name = "VDDOUT25"; | |
| regulator-min-microvolt = <2500000>; | |
| regulator-max-microvolt = <2500000>; | |
| regulator-boot-on; | |
| status = "disabled"; | |
| }; | |
| ns_sram: sram@100000 { | |
| compatible = "mmio-sram"; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| reg = <0x100000 0x20000>; | |
| ranges; | |
| }; | |
| thermal_sensor: thermal-sensor { | |
| compatible = "generic-adc-thermal"; | |
| #thermal-sensor-cells = <0>; | |
| io-channels = <&adc AT91_SAMA7G5_ADC_TEMP_CHANNEL>; | |
| io-channel-names = "sensor-channel"; | |
| }; | |
| soc { | |
| compatible = "simple-bus"; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges; | |
| nfc_sram: sram@600000 { | |
| compatible = "mmio-sram"; | |
| no-memory-wc; | |
| reg = <0x00600000 0x2400>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0 0x00600000 0x2400>; | |
| }; | |
| nfc_io: nfc-io@10000000 { | |
| compatible = "atmel,sama5d3-nfc-io", "syscon"; | |
| reg = <0x10000000 0x8000000>; | |
| }; | |
| ebi: ebi@40000000 { | |
| compatible = "atmel,sama5d3-ebi"; | |
| #address-cells = <2>; | |
| #size-cells = <1>; | |
| atmel,smc = <&hsmc>; | |
| reg = <0x40000000 0x20000000>; | |
| ranges = <0x0 0x0 0x40000000 0x8000000 | |
| 0x1 0x0 0x48000000 0x8000000 | |
| 0x2 0x0 0x50000000 0x8000000 | |
| 0x3 0x0 0x58000000 0x8000000>; | |
| clocks = <&pmc PMC_TYPE_CORE PMC_MCK1>; | |
| status = "disabled"; | |
| nand_controller: nand-controller { | |
| compatible = "atmel,sama5d3-nand-controller"; | |
| atmel,nfc-sram = <&nfc_sram>; | |
| atmel,nfc-io = <&nfc_io>; | |
| ecc-engine = <&pmecc>; | |
| #address-cells = <2>; | |
| #size-cells = <1>; | |
| ranges; | |
| status = "disabled"; | |
| }; | |
| }; | |
| securam: sram@e0000000 { | |
| compatible = "microchip,sama7g5-securam", "atmel,sama5d2-securam", "mmio-sram"; | |
| reg = <0xe0000000 0x4000>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 18>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0 0xe0000000 0x4000>; | |
| no-memory-wc; | |
| }; | |
| secumod: secumod@e0004000 { | |
| compatible = "microchip,sama7g5-secumod", "atmel,sama5d2-secumod", "syscon"; | |
| reg = <0xe0004000 0x4000>; | |
| gpio-controller; | |
| #gpio-cells = <2>; | |
| }; | |
| sfrbu: sfr@e0008000 { | |
| compatible = "microchip,sama7g5-sfrbu", "atmel,sama5d2-sfrbu", "syscon"; | |
| reg = <0xe0008000 0x20>; | |
| }; | |
| pioA: pinctrl@e0014000 { | |
| compatible = "microchip,sama7g5-pinctrl"; | |
| reg = <0xe0014000 0x800>; | |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-controller; | |
| #interrupt-cells = <2>; | |
| gpio-controller; | |
| #gpio-cells = <2>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 11>; | |
| }; | |
| pmc: clock-controller@e0018000 { | |
| compatible = "microchip,sama7g5-pmc", "syscon"; | |
| reg = <0xe0018000 0x200>; | |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; | |
| #clock-cells = <2>; | |
| clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>; | |
| clock-names = "td_slck", "md_slck", "main_xtal"; | |
| }; | |
| reset_controller: reset-controller@e001d000 { | |
| compatible = "microchip,sama7g5-rstc"; | |
| reg = <0xe001d000 0xc>, <0xe001d0e4 0x4>; | |
| #reset-cells = <1>; | |
| clocks = <&clk32k 0>; | |
| }; | |
| shdwc: poweroff@e001d010 { | |
| compatible = "microchip,sama7g5-shdwc", "syscon"; | |
| reg = <0xe001d010 0x10>; | |
| clocks = <&clk32k 0>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| atmel,wakeup-rtc-timer; | |
| atmel,wakeup-rtt-timer; | |
| status = "disabled"; | |
| }; | |
| rtt: rtc@e001d020 { | |
| compatible = "microchip,sama7g5-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt"; | |
| reg = <0xe001d020 0x30>; | |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clk32k 0>; | |
| }; | |
| clk32k: clock-controller@e001d050 { | |
| compatible = "microchip,sama7g5-sckc", "microchip,sam9x60-sckc"; | |
| reg = <0xe001d050 0x4>; | |
| clocks = <&slow_xtal>; | |
| #clock-cells = <1>; | |
| }; | |
| gpbr: gpbr@e001d060 { | |
| compatible = "microchip,sama7g5-gpbr", "syscon"; | |
| reg = <0xe001d060 0x48>; | |
| }; | |
| rtc: rtc@e001d0a8 { | |
| compatible = "microchip,sama7g5-rtc", "microchip,sam9x60-rtc"; | |
| reg = <0xe001d0a8 0x30>; | |
| interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clk32k 1>; | |
| }; | |
| ps_wdt: watchdog@e001d180 { | |
| compatible = "microchip,sama7g5-wdt"; | |
| reg = <0xe001d180 0x24>; | |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&clk32k 0>; | |
| }; | |
| chipid@e0020000 { | |
| compatible = "microchip,sama7g5-chipid"; | |
| reg = <0xe0020000 0x8>; | |
| }; | |
| tcb1: timer@e0800000 { | |
| compatible = "atmel,sama5d2-tcb", "simple-mfd", "syscon"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| reg = <0xe0800000 0x100>; | |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 91>, <&pmc PMC_TYPE_PERIPHERAL 92>, <&pmc PMC_TYPE_PERIPHERAL 93>, <&clk32k 1>; | |
| clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk"; | |
| }; | |
| hsmc: hsmc@e0808000 { | |
| compatible = "atmel,sama5d2-smc", "syscon", "simple-mfd"; | |
| reg = <0xe0808000 0x1000>; | |
| interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 21>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges; | |
| pmecc: ecc-engine@e0808070 { | |
| compatible = "atmel,sama5d2-pmecc"; | |
| reg = <0xe0808070 0x490>, | |
| <0xe0808500 0x200>; | |
| }; | |
| }; | |
| qspi0: spi@e080c000 { | |
| compatible = "microchip,sama7g5-ospi"; | |
| reg = <0xe080c000 0x400>, <0x20000000 0x10000000>; | |
| reg-names = "qspi_base", "qspi_mmap"; | |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(41)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(40)>; | |
| dma-names = "tx", "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 78>, <&pmc PMC_TYPE_GCK 78>; | |
| clock-names = "pclk", "gclk"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| qspi1: spi@e0810000 { | |
| compatible = "microchip,sama7g5-qspi"; | |
| reg = <0xe0810000 0x400>, <0x30000000 0x10000000>; | |
| reg-names = "qspi_base", "qspi_mmap"; | |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(43)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(42)>; | |
| dma-names = "tx", "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 79>, <&pmc PMC_TYPE_GCK 79>; | |
| clock-names = "pclk", "gclk"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| }; | |
| can0: can@e0828000 { | |
| compatible = "bosch,m_can"; | |
| reg = <0xe0828000 0x100>, <0x100000 0x7800>; | |
| reg-names = "m_can", "message_ram"; | |
| interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "int0", "int1"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 61>, <&pmc PMC_TYPE_GCK 61>; | |
| clock-names = "hclk", "cclk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 61>; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clock-rates = <40000000>; | |
| bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>; | |
| status = "disabled"; | |
| }; | |
| can1: can@e082c000 { | |
| compatible = "bosch,m_can"; | |
| reg = <0xe082c000 0x100>, <0x100000 0xbc00>; | |
| reg-names = "m_can", "message_ram"; | |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "int0", "int1"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 62>, <&pmc PMC_TYPE_GCK 62>; | |
| clock-names = "hclk", "cclk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 62>; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clock-rates = <40000000>; | |
| bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>; | |
| status = "disabled"; | |
| }; | |
| can2: can@e0830000 { | |
| compatible = "bosch,m_can"; | |
| reg = <0xe0830000 0x100>, <0x100000 0x10000>; | |
| reg-names = "m_can", "message_ram"; | |
| interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "int0", "int1"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 63>, <&pmc PMC_TYPE_GCK 63>; | |
| clock-names = "hclk", "cclk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 63>; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clock-rates = <40000000>; | |
| bosch,mram-cfg = <0xbc00 0 0 64 0 0 32 32>; | |
| status = "disabled"; | |
| }; | |
| can3: can@e0834000 { | |
| compatible = "bosch,m_can"; | |
| reg = <0xe0834000 0x100>, <0x110000 0x4400>; | |
| reg-names = "m_can", "message_ram"; | |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "int0", "int1"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 64>, <&pmc PMC_TYPE_GCK 64>; | |
| clock-names = "hclk", "cclk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 64>; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clock-rates = <40000000>; | |
| bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>; | |
| status = "disabled"; | |
| }; | |
| can4: can@e0838000 { | |
| compatible = "bosch,m_can"; | |
| reg = <0xe0838000 0x100>, <0x110000 0x8800>; | |
| reg-names = "m_can", "message_ram"; | |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "int0", "int1"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 65>, <&pmc PMC_TYPE_GCK 65>; | |
| clock-names = "hclk", "cclk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 65>; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clock-rates = <40000000>; | |
| bosch,mram-cfg = <0x4400 0 0 64 0 0 32 32>; | |
| status = "disabled"; | |
| }; | |
| can5: can@e083c000 { | |
| compatible = "bosch,m_can"; | |
| reg = <0xe083c000 0x100>, <0x110000 0xcc00>; | |
| reg-names = "m_can", "message_ram"; | |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; | |
| interrupt-names = "int0", "int1"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 66>, <&pmc PMC_TYPE_GCK 66>; | |
| clock-names = "hclk", "cclk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 66>; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clock-rates = <40000000>; | |
| bosch,mram-cfg = <0x8800 0 0 64 0 0 32 32>; | |
| status = "disabled"; | |
| }; | |
| adc: adc@e1000000 { | |
| compatible = "microchip,sama7g5-adc"; | |
| reg = <0xe1000000 0x200>; | |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_GCK 26>; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 26>; | |
| assigned-clock-rates = <100000000>; | |
| clock-names = "adc_clk"; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(0)>; | |
| dma-names = "rx"; | |
| atmel,min-sample-rate-hz = <200000>; | |
| atmel,max-sample-rate-hz = <20000000>; | |
| atmel,startup-time-ms = <4>; | |
| #io-channel-cells = <1>; | |
| nvmem-cells = <&temperature_calib>; | |
| nvmem-cell-names = "temperature_calib"; | |
| status = "disabled"; | |
| }; | |
| sdmmc0: mmc@e1204000 { | |
| compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci"; | |
| reg = <0xe1204000 0x4000>; | |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 80>, <&pmc PMC_TYPE_GCK 80>; | |
| clock-names = "hclock", "multclk"; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 80>; | |
| assigned-clock-rates = <200000000>; | |
| microchip,sdcal-inverted; | |
| status = "disabled"; | |
| }; | |
| sdmmc1: mmc@e1208000 { | |
| compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci"; | |
| reg = <0xe1208000 0x4000>; | |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 81>, <&pmc PMC_TYPE_GCK 81>; | |
| clock-names = "hclock", "multclk"; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 81>; | |
| assigned-clock-rates = <200000000>; | |
| microchip,sdcal-inverted; | |
| status = "disabled"; | |
| }; | |
| sdmmc2: mmc@e120c000 { | |
| compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci"; | |
| reg = <0xe120c000 0x4000>; | |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 82>, <&pmc PMC_TYPE_GCK 82>; | |
| clock-names = "hclock", "multclk"; | |
| assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 82>; | |
| assigned-clock-rates = <200000000>; | |
| microchip,sdcal-inverted; | |
| status = "disabled"; | |
| }; | |
| csi2dc: csi2dc@e1404000 { | |
| compatible = "microchip,sama7g5-csi2dc"; | |
| reg = <0xe1404000 0x500>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&xisc>; | |
| clock-names = "pclk", "scck"; | |
| assigned-clocks = <&xisc>; | |
| assigned-clock-rates = <266000000>; | |
| status = "disabled"; | |
| ports { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| port@0 { | |
| reg = <0>; | |
| csi2dc_in: endpoint { | |
| }; | |
| }; | |
| port@1 { | |
| reg = <1>; | |
| csi2dc_out: endpoint { | |
| bus-width = <14>; | |
| hsync-active = <1>; | |
| vsync-active = <1>; | |
| remote-endpoint = <&xisc_in>; | |
| }; | |
| }; | |
| }; | |
| }; | |
| xisc: xisc@e1408000 { | |
| compatible = "microchip,sama7g5-isc"; | |
| reg = <0xe1408000 0x2000>; | |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 56>; | |
| clock-names = "hclock"; | |
| #clock-cells = <0>; | |
| clock-output-names = "isc-mck"; | |
| status = "disabled"; | |
| port { | |
| xisc_in: endpoint { | |
| bus-type = <5>; /* Parallel */ | |
| bus-width = <14>; | |
| hsync-active = <1>; | |
| vsync-active = <1>; | |
| remote-endpoint = <&csi2dc_out>; | |
| }; | |
| }; | |
| }; | |
| pwm: pwm@e1604000 { | |
| compatible = "microchip,sama7g5-pwm", "atmel,sama5d2-pwm"; | |
| reg = <0xe1604000 0x4000>; | |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; | |
| #pwm-cells = <3>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 77>; | |
| status = "disabled"; | |
| }; | |
| pdmc0: sound@e1608000 { | |
| compatible = "microchip,sama7g5-pdmc"; | |
| reg = <0xe1608000 0x1000>; | |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; | |
| #sound-dai-cells = <0>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(37)>; | |
| dma-names = "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 68>, <&pmc PMC_TYPE_GCK 68>; | |
| clock-names = "pclk", "gclk"; | |
| status = "disabled"; | |
| }; | |
| pdmc1: sound@e160c000 { | |
| compatible = "microchip,sama7g5-pdmc"; | |
| reg = <0xe160c000 0x1000>; | |
| interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; | |
| #sound-dai-cells = <0>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(38)>; | |
| dma-names = "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 69>, <&pmc PMC_TYPE_GCK 69>; | |
| clock-names = "pclk", "gclk"; | |
| status = "disabled"; | |
| }; | |
| spdifrx: spdifrx@e1614000 { | |
| #sound-dai-cells = <0>; | |
| compatible = "microchip,sama7g5-spdifrx"; | |
| reg = <0xe1614000 0x4000>; | |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(49)>; | |
| dma-names = "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 84>, <&pmc PMC_TYPE_GCK 84>; | |
| clock-names = "pclk", "gclk"; | |
| status = "disabled"; | |
| }; | |
| spdiftx: spdiftx@e1618000 { | |
| #sound-dai-cells = <0>; | |
| compatible = "microchip,sama7g5-spdiftx"; | |
| reg = <0xe1618000 0x4000>; | |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(50)>; | |
| dma-names = "tx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 85>, <&pmc PMC_TYPE_GCK 85>; | |
| clock-names = "pclk", "gclk"; | |
| }; | |
| i2s0: i2s@e161c000 { | |
| compatible = "microchip,sama7g5-i2smcc"; | |
| #sound-dai-cells = <0>; | |
| reg = <0xe161c000 0x4000>; | |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(34)>, <&dma0 AT91_XDMAC_DT_PERID(33)>; | |
| dma-names = "tx", "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 57>, <&pmc PMC_TYPE_GCK 57>; | |
| clock-names = "pclk", "gclk"; | |
| status = "disabled"; | |
| }; | |
| i2s1: i2s@e1620000 { | |
| compatible = "microchip,sama7g5-i2smcc"; | |
| #sound-dai-cells = <0>; | |
| reg = <0xe1620000 0x4000>; | |
| interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(36)>, <&dma0 AT91_XDMAC_DT_PERID(35)>; | |
| dma-names = "tx", "rx"; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>; | |
| clock-names = "pclk", "gclk"; | |
| status = "disabled"; | |
| }; | |
| eic: interrupt-controller@e1628000 { | |
| compatible = "microchip,sama7g5-eic"; | |
| reg = <0xe1628000 0xec>; | |
| interrupt-parent = <&gic>; | |
| interrupt-controller; | |
| #interrupt-cells = <2>; | |
| interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 37>; | |
| clock-names = "pclk"; | |
| status = "disabled"; | |
| }; | |
| pit64b0: timer@e1800000 { | |
| compatible = "microchip,sama7g5-pit64b", "microchip,sam9x60-pit64b"; | |
| reg = <0xe1800000 0x4000>; | |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 70>, <&pmc PMC_TYPE_GCK 70>; | |
| clock-names = "pclk", "gclk"; | |
| }; | |
| pit64b1: timer@e1804000 { | |
| compatible = "microchip,sama7g5-pit64b", "microchip,sam9x60-pit64b"; | |
| reg = <0xe1804000 0x4000>; | |
| interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 71>, <&pmc PMC_TYPE_GCK 71>; | |
| clock-names = "pclk", "gclk"; | |
| }; | |
| aes: crypto@e1810000 { | |
| compatible = "atmel,at91sam9g46-aes"; | |
| reg = <0xe1810000 0x100>; | |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 27>; | |
| clock-names = "aes_clk"; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(1)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(2)>; | |
| dma-names = "tx", "rx"; | |
| }; | |
| sha: crypto@e1814000 { | |
| compatible = "atmel,at91sam9g46-sha"; | |
| reg = <0xe1814000 0x100>; | |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 83>; | |
| clock-names = "sha_clk"; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(48)>; | |
| dma-names = "tx"; | |
| }; | |
| flx0: flexcom@e1818000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe1818000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 38>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe1818000 0x800>; | |
| status = "disabled"; | |
| uart0: serial@200 { | |
| compatible = "atmel,at91sam9260-usart"; | |
| reg = <0x200 0x200>; | |
| atmel,usart-mode = <AT91_USART_MODE_SERIAL>; | |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 38>; | |
| clock-names = "usart"; | |
| dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>, | |
| <&dma1 AT91_XDMAC_DT_PERID(5)>; | |
| dma-names = "tx", "rx"; | |
| atmel,use-dma-rx; | |
| atmel,use-dma-tx; | |
| status = "disabled"; | |
| }; | |
| }; | |
| flx1: flexcom@e181c000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe181c000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 39>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe181c000 0x800>; | |
| status = "disabled"; | |
| i2c1: i2c@600 { | |
| compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c"; | |
| reg = <0x600 0x200>; | |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 39>; | |
| atmel,fifo-size = <32>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(7)>; | |
| dma-names = "tx", "rx"; | |
| status = "disabled"; | |
| }; | |
| }; | |
| flx3: flexcom@e1824000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe1824000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 41>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe1824000 0x800>; | |
| status = "disabled"; | |
| uart3: serial@200 { | |
| compatible = "atmel,at91sam9260-usart"; | |
| reg = <0x200 0x200>; | |
| atmel,usart-mode = <AT91_USART_MODE_SERIAL>; | |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 41>; | |
| clock-names = "usart"; | |
| dmas = <&dma1 AT91_XDMAC_DT_PERID(12)>, | |
| <&dma1 AT91_XDMAC_DT_PERID(11)>; | |
| dma-names = "tx", "rx"; | |
| atmel,use-dma-rx; | |
| atmel,use-dma-tx; | |
| status = "disabled"; | |
| }; | |
| }; | |
| trng: rng@e2010000 { | |
| compatible = "microchip,sama7g5-trng", "atmel,at91sam9g45-trng"; | |
| reg = <0xe2010000 0x100>; | |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 97>; | |
| status = "disabled"; | |
| }; | |
| tdes: crypto@e2014000 { | |
| compatible = "atmel,at91sam9g46-tdes"; | |
| reg = <0xe2014000 0x100>; | |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 96>; | |
| clock-names = "tdes_clk"; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(54)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(53)>; | |
| dma-names = "tx", "rx"; | |
| }; | |
| flx4: flexcom@e2018000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe2018000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 42>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe2018000 0x800>; | |
| status = "disabled"; | |
| uart4: serial@200 { | |
| compatible = "atmel,at91sam9260-usart"; | |
| reg = <0x200 0x200>; | |
| atmel,usart-mode = <AT91_USART_MODE_SERIAL>; | |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 42>; | |
| clock-names = "usart"; | |
| dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>, | |
| <&dma1 AT91_XDMAC_DT_PERID(13)>; | |
| dma-names = "tx", "rx"; | |
| atmel,use-dma-rx; | |
| atmel,use-dma-tx; | |
| atmel,fifo-size = <16>; | |
| status = "disabled"; | |
| }; | |
| }; | |
| flx7: flexcom@e2024000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe2024000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 45>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe2024000 0x800>; | |
| status = "disabled"; | |
| uart7: serial@200 { | |
| compatible = "atmel,at91sam9260-usart"; | |
| reg = <0x200 0x200>; | |
| atmel,usart-mode = <AT91_USART_MODE_SERIAL>; | |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 45>; | |
| clock-names = "usart"; | |
| dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>, | |
| <&dma1 AT91_XDMAC_DT_PERID(19)>; | |
| dma-names = "tx", "rx"; | |
| atmel,use-dma-rx; | |
| atmel,use-dma-tx; | |
| atmel,fifo-size = <16>; | |
| status = "disabled"; | |
| }; | |
| }; | |
| gmac0: ethernet@e2800000 { | |
| compatible = "microchip,sama7g5-gem"; | |
| reg = <0xe2800000 0x1000>; | |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_GCK 51>, <&pmc PMC_TYPE_GCK 53>; | |
| clock-names = "pclk", "hclk", "tx_clk", "tsu_clk"; | |
| assigned-clocks = <&pmc PMC_TYPE_GCK 51>; | |
| assigned-clock-rates = <125000000>; | |
| status = "disabled"; | |
| }; | |
| gmac1: ethernet@e2804000 { | |
| compatible = "microchip,sama7g5-emac"; | |
| reg = <0xe2804000 0x1000>; | |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, | |
| <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 52>, <&pmc PMC_TYPE_PERIPHERAL 52>; | |
| clock-names = "pclk", "hclk"; | |
| status = "disabled"; | |
| }; | |
| dma0: dma-controller@e2808000 { | |
| compatible = "microchip,sama7g5-dma"; | |
| reg = <0xe2808000 0x1000>; | |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; | |
| #dma-cells = <1>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 22>; | |
| clock-names = "dma_clk"; | |
| status = "disabled"; | |
| }; | |
| dma1: dma-controller@e280c000 { | |
| compatible = "microchip,sama7g5-dma"; | |
| reg = <0xe280c000 0x1000>; | |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; | |
| #dma-cells = <1>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 23>; | |
| clock-names = "dma_clk"; | |
| status = "disabled"; | |
| }; | |
| /* Place dma2 here despite it's address */ | |
| dma2: dma-controller@e1200000 { | |
| compatible = "microchip,sama7g5-dma"; | |
| reg = <0xe1200000 0x1000>; | |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; | |
| #dma-cells = <1>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 24>; | |
| clock-names = "dma_clk"; | |
| dma-requests = <0>; | |
| status = "disabled"; | |
| }; | |
| tcb0: timer@e2814000 { | |
| compatible = "atmel,sama5d2-tcb", "simple-mfd", "syscon"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| reg = <0xe2814000 0x100>; | |
| interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 88>, <&pmc PMC_TYPE_PERIPHERAL 89>, <&pmc PMC_TYPE_PERIPHERAL 90>, <&clk32k 1>; | |
| clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk"; | |
| }; | |
| flx8: flexcom@e2818000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe2818000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 46>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe2818000 0x800>; | |
| status = "disabled"; | |
| i2c8: i2c@600 { | |
| compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c"; | |
| reg = <0x600 0x200>; | |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 46>; | |
| atmel,fifo-size = <32>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(21)>; | |
| dma-names = "tx", "rx"; | |
| status = "disabled"; | |
| }; | |
| }; | |
| flx9: flexcom@e281c000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe281c000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 47>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe281c000 0x800>; | |
| status = "disabled"; | |
| i2c9: i2c@600 { | |
| compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c"; | |
| reg = <0x600 0x200>; | |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 47>; | |
| atmel,fifo-size = <32>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(23)>; | |
| dma-names = "tx", "rx"; | |
| status = "disabled"; | |
| }; | |
| }; | |
| flx10: flexcom@e2820000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe2820000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 48>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe2820000 0x800>; | |
| status = "disabled"; | |
| i2c10: i2c@600 { | |
| compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c"; | |
| reg = <0x600 0x200>; | |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 48>; | |
| atmel,fifo-size = <32>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(26)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(25)>; | |
| dma-names = "tx", "rx"; | |
| status = "disabled"; | |
| }; | |
| }; | |
| flx11: flexcom@e2824000 { | |
| compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom"; | |
| reg = <0xe2824000 0x200>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 49>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges = <0x0 0xe2824000 0x800>; | |
| status = "disabled"; | |
| spi11: spi@400 { | |
| compatible = "atmel,at91rm9200-spi"; | |
| reg = <0x400 0x200>; | |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; | |
| clocks = <&pmc PMC_TYPE_PERIPHERAL 49>; | |
| clock-names = "spi_clk"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| atmel,fifo-size = <32>; | |
| dmas = <&dma0 AT91_XDMAC_DT_PERID(28)>, | |
| <&dma0 AT91_XDMAC_DT_PERID(27)>; | |
| dma-names = "tx", "rx"; | |
| status = "disabled"; | |
| }; | |
| }; | |
| uddrc: uddrc@e3800000 { | |
| compatible = "microchip,sama7g5-uddrc"; | |
| reg = <0xe3800000 0x4000>; | |
| }; | |
| ddr3phy: ddr3phy@e3804000 { | |
| compatible = "microchip,sama7g5-ddr3phy"; | |
| reg = <0xe3804000 0x1000>; | |
| }; | |
| otpc: efuse@e8c00000 { | |
| compatible = "microchip,sama7g5-otpc", "syscon"; | |
| reg = <0xe8c00000 0x100>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| temperature_calib: calib@1 { | |
| reg = <OTP_PKT(1) 76>; | |
| }; | |
| }; | |
| gic: interrupt-controller@e8c11000 { | |
| compatible = "arm,cortex-a7-gic"; | |
| #interrupt-cells = <3>; | |
| #address-cells = <0>; | |
| interrupt-controller; | |
| reg = <0xe8c11000 0x1000>, | |
| <0xe8c12000 0x2000>; | |
| }; | |
| }; | |
| }; |