include/configs/mx7dsabresd.h - u-boot - Git at Google


            
            /*

            
             * Copyright (C) 2015 Freescale Semiconductor, Inc.

            
             *

            
             * Configuration settings for the Freescale i.MX7D SABRESD board.

            
             *

            
             * SPDX-License-Identifier:	GPL-2.0+

            
             */


            #ifndef __MX7D_SABRESD_CONFIG_H

            
            #define __MX7D_SABRESD_CONFIG_H


            #include "mx7_common.h"


            #define CONFIG_DBG_MONITOR

            
            #define PHYS_SDRAM_SIZE			SZ_1G


            #define CONFIG_MXC_UART_BASE            UART1_IPS_BASE_ADDR


            /* Size of malloc() pool */

            
            #define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)


            /* Network */

            
            #define CONFIG_FEC_MXC

            
            #define CONFIG_MII

            
            #define CONFIG_FEC_XCV_TYPE             RGMII

            
            #define CONFIG_ETHPRIME                 "FEC"

            
            #define CONFIG_FEC_MXC_PHYADDR          0


            #define CONFIG_PHY_BROADCOM

            
            /* ENET1 */

            
            #define IMX_FEC_BASE			ENET_IPS_BASE_ADDR


            /* MMC Config*/

            
            #define CONFIG_SYS_FSL_ESDHC_ADDR       0


            #undef CONFIG_BOOTM_NETBSD

            
            #undef CONFIG_BOOTM_PLAN9

            
            #undef CONFIG_BOOTM_RTEMS


            /* I2C configs */

            
            #define CONFIG_SYS_I2C_MXC

            
            #define CONFIG_SYS_I2C_SPEED		100000


            #define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */

            
            #define CONFIG_SYS_MMC_IMG_LOAD_PART	1


            #ifdef CONFIG_IMX_BOOTAUX

            
            /* Set to QSPI1 A flash at default */

            
            #define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000


            #define UPDATE_M4_ENV \

            
            	"m4image=m4_qspi.bin\0" \

            
            	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \

            
            	"update_m4_from_sd=" \

            
            		"if sf probe 0:0; then " \

            
            			"if run loadm4image; then " \

            
            				"setexpr fw_sz ${filesize} + 0xffff; " \

            
            				"setexpr fw_sz ${fw_sz} / 0x10000; "	\

            
            				"setexpr fw_sz ${fw_sz} * 0x10000; "	\

            
            				"sf erase 0x0 ${fw_sz}; " \

            
            				"sf write ${loadaddr} 0x0 ${filesize}; " \

            
            			"fi; " \

            
            		"fi\0" \

            
            	"m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"

            
            #else

            
            #define UPDATE_M4_ENV ""

            
            #endif


            #define CONFIG_MFG_ENV_SETTINGS \

            
            	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \

            
            		"rdinit=/linuxrc " \

            
            		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \

            
            		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\

            
            		"g_mass_storage.iSerialNumber=\"\" "\

            
            		"clk_ignore_unused "\

            
            		"\0" \

            
            	"initrd_addr=0x83800000\0" \

            
            	"initrd_high=0xffffffff\0" \

            
            	"bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \


            #define CONFIG_DFU_ENV_SETTINGS \

            
            	"dfu_alt_info=image raw 0 0x800000;"\

            
            		"u-boot raw 0 0x4000;"\

            
            		"bootimg part 0 1;"\

            
            		"rootfs part 0 2\0" \


            #define CONFIG_EXTRA_ENV_SETTINGS \

            
            	UPDATE_M4_ENV \

            
            	CONFIG_MFG_ENV_SETTINGS \

            
            	CONFIG_DFU_ENV_SETTINGS \

            
            	"script=boot.scr\0" \

            
            	"image=zImage\0" \

            
            	"console=ttymxc0\0" \

            
            	"fdt_high=0xffffffff\0" \

            
            	"initrd_high=0xffffffff\0" \

            
            	"fdt_file=imx7d-sdb.dtb\0" \

            
            	"fdt_addr=0x83000000\0" \

            
            	"boot_fdt=try\0" \

            
            	"ip_dyn=yes\0" \

            
            	"videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \

            
            	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \

            
            	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \

            
            	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \

            
            	"mmcautodetect=yes\0" \

            
            	"mmcargs=setenv bootargs console=${console},${baudrate} " \

            
            		"root=${mmcroot}\0" \

            
            	"loadbootscript=" \

            
            		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \

            
            	"bootscript=echo Running bootscript from mmc ...; " \

            
            		"source\0" \

            
            	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \

            
            	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \

            
            	"mmcboot=echo Booting from mmc ...; " \

            
            		"run mmcargs; " \

            
            		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \

            
            			"if run loadfdt; then " \

            
            				"bootz ${loadaddr} - ${fdt_addr}; " \

            
            			"else " \

            
            				"if test ${boot_fdt} = try; then " \

            
            					"bootz; " \

            
            				"else " \

            
            					"echo WARN: Cannot load the DT; " \

            
            				"fi; " \

            
            			"fi; " \

            
            		"else " \

            
            			"bootz; " \

            
            		"fi;\0" \

            
            	"netargs=setenv bootargs console=${console},${baudrate} " \

            
            		"root=/dev/nfs " \

            
            	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \

            
            		"netboot=echo Booting from net ...; " \

            
            		"run netargs; " \

            
            		"if test ${ip_dyn} = yes; then " \

            
            			"setenv get_cmd dhcp; " \

            
            		"else " \

            
            			"setenv get_cmd tftp; " \

            
            		"fi; " \

            
            		"${get_cmd} ${image}; " \

            
            		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \

            
            			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \

            
            				"bootz ${loadaddr} - ${fdt_addr}; " \

            
            			"else " \

            
            				"if test ${boot_fdt} = try; then " \

            
            					"bootz; " \

            
            				"else " \

            
            					"echo WARN: Cannot load the DT; " \

            
            				"fi; " \

            
            			"fi; " \

            
            		"else " \

            
            			"bootz; " \

            
            		"fi;\0"


            #define CONFIG_BOOTCOMMAND \

            
            	   "mmc dev ${mmcdev};" \

            
            	   "mmc dev ${mmcdev}; if mmc rescan; then " \

            
            		   "if run loadbootscript; then " \

            
            			   "run bootscript; " \

            
            		   "else " \

            
            			   "if run loadimage; then " \

            
            				   "run mmcboot; " \

            
            			   "else run netboot; " \

            
            			   "fi; " \

            
            		   "fi; " \

            
            	   "else run netboot; fi"


            #define CONFIG_SYS_MEMTEST_START	0x80000000

            
            #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)


            #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

            
            #define CONFIG_SYS_HZ			1000


            /* Physical Memory Map */

            
            #define CONFIG_NR_DRAM_BANKS		1

            
            #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR


            #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM

            
            #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR

            
            #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE


            #define CONFIG_SYS_INIT_SP_OFFSET \

            
            	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

            
            #define CONFIG_SYS_INIT_SP_ADDR \

            
            	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)


            /* environment organization */

            
            #define CONFIG_ENV_SIZE			SZ_8K


            /*

            
             * If want to use nand, define CONFIG_NAND_MXS and rework board

            
             * to support nand, since emmc has pin conflicts with nand

            
             */

            
            #ifdef CONFIG_NAND_MXS

            
            /* NAND stuff */

            
            #define CONFIG_SYS_MAX_NAND_DEVICE	1

            
            #define CONFIG_SYS_NAND_BASE		0x40000000

            
            #define CONFIG_SYS_NAND_5_ADDR_CYCLE

            
            #define CONFIG_SYS_NAND_ONFI_DETECTION


            /* DMA stuff, needed for GPMI/MXS NAND support */

            
            #define CONFIG_APBH_DMA

            
            #define CONFIG_APBH_DMA_BURST

            
            #define CONFIG_APBH_DMA_BURST8

            
            #endif


            #define CONFIG_ENV_OFFSET		(12 * SZ_64K)

            
            #ifdef CONFIG_NAND_MXS

            
            #define CONFIG_SYS_FSL_USDHC_NUM	1

            
            #else

            
            #define CONFIG_SYS_FSL_USDHC_NUM	2

            
            #endif


            #define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC1 */

            
            #define CONFIG_SYS_MMC_ENV_PART		0	/* user area */

            
            #define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */


            /* USB Configs */

            
            #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)


            #define CONFIG_IMX_THERMAL


            #define CONFIG_USBD_HS


            #define CONFIG_USB_FUNCTION_MASS_STORAGE


            #ifdef CONFIG_VIDEO

            
            #define CONFIG_VIDEO_MXS

            
            #define CONFIG_VIDEO_LOGO

            
            #define CONFIG_SPLASH_SCREEN

            
            #define CONFIG_SPLASH_SCREEN_ALIGN

            
            #define CONFIG_BMP_16BPP

            
            #define CONFIG_VIDEO_BMP_RLE8

            
            #define CONFIG_VIDEO_BMP_LOGO

            
            #endif


            #ifdef CONFIG_FSL_QSPI

            
            #define CONFIG_SPI_FLASH

            
            #define CONFIG_SPI_FLASH_MACRONIX

            
            #define CONFIG_SPI_FLASH_BAR

            
            #define CONFIG_SF_DEFAULT_BUS		0

            
            #define CONFIG_SF_DEFAULT_CS		0

            
            #define CONFIG_SF_DEFAULT_SPEED		40000000

            
            #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0

            
            #define FSL_QSPI_FLASH_NUM		1

            
            #define FSL_QSPI_FLASH_SIZE		SZ_64M

            
            #define QSPI0_BASE_ADDR			QSPI1_IPS_BASE_ADDR

            
            #define QSPI0_AMBA_BASE			QSPI0_ARB_BASE_ADDR

            
            #endif


            #endif	/* __CONFIG_H */
	/*
	* Copyright (C) 2015 Freescale Semiconductor, Inc.
	*
	* Configuration settings for the Freescale i.MX7D SABRESD board.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __MX7D_SABRESD_CONFIG_H
	#define __MX7D_SABRESD_CONFIG_H

	#include "mx7_common.h"

	#define CONFIG_DBG_MONITOR
	#define PHYS_SDRAM_SIZE SZ_1G

	#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)

	/* Network */
	#define CONFIG_FEC_MXC
	#define CONFIG_MII
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_ETHPRIME "FEC"
	#define CONFIG_FEC_MXC_PHYADDR 0

	#define CONFIG_PHY_BROADCOM
	/* ENET1 */
	#define IMX_FEC_BASE ENET_IPS_BASE_ADDR

	/* MMC Config*/
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0

	#undef CONFIG_BOOTM_NETBSD
	#undef CONFIG_BOOTM_PLAN9
	#undef CONFIG_BOOTM_RTEMS

	/* I2C configs */
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_SPEED 100000

	#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
	#define CONFIG_SYS_MMC_IMG_LOAD_PART 1

	#ifdef CONFIG_IMX_BOOTAUX
	/* Set to QSPI1 A flash at default */
	#define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000

	#define UPDATE_M4_ENV \
	"m4image=m4_qspi.bin\0" \
	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
	"update_m4_from_sd=" \
	"if sf probe 0:0; then " \
	"if run loadm4image; then " \
	"setexpr fw_sz ${filesize} + 0xffff; " \
	"setexpr fw_sz ${fw_sz} / 0x10000; " \
	"setexpr fw_sz ${fw_sz} * 0x10000; " \
	"sf erase 0x0 ${fw_sz}; " \
	"sf write ${loadaddr} 0x0 ${filesize}; " \
	"fi; " \
	"fi\0" \
	"m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
	#else
	#define UPDATE_M4_ENV ""
	#endif

	#define CONFIG_MFG_ENV_SETTINGS \
	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
	"rdinit=/linuxrc " \
	"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
	"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
	"g_mass_storage.iSerialNumber=\"\" "\
	"clk_ignore_unused "\
	"\0" \
	"initrd_addr=0x83800000\0" \
	"initrd_high=0xffffffff\0" \
	"bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \

	#define CONFIG_DFU_ENV_SETTINGS \
	"dfu_alt_info=image raw 0 0x800000;"\
	"u-boot raw 0 0x4000;"\
	"bootimg part 0 1;"\
	"rootfs part 0 2\0" \

	#define CONFIG_EXTRA_ENV_SETTINGS \
	UPDATE_M4_ENV \
	CONFIG_MFG_ENV_SETTINGS \
	CONFIG_DFU_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=zImage\0" \
	"console=ttymxc0\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_file=imx7d-sdb.dtb\0" \
	"fdt_addr=0x83000000\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
	"root=${mmcroot}\0" \
	"loadbootscript=" \
	"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if run loadfdt; then " \
	"bootz ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"if test ${boot_fdt} = try; then " \
	"bootz; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"fi; " \
	"else " \
	"bootz; " \
	"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
	"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
	"run netargs; " \
	"if test ${ip_dyn} = yes; then " \
	"setenv get_cmd dhcp; " \
	"else " \
	"setenv get_cmd tftp; " \
	"fi; " \
	"${get_cmd} ${image}; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
	"bootz ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"if test ${boot_fdt} = try; then " \
	"bootz; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"fi; " \
	"else " \
	"bootz; " \
	"fi;\0"

	#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev};" \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loadimage; then " \
	"run mmcboot; " \
	"else run netboot; " \
	"fi; " \
	"fi; " \
	"else run netboot; fi"

	#define CONFIG_SYS_MEMTEST_START 0x80000000
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	#define CONFIG_SYS_HZ 1000

	/* Physical Memory Map */
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	/* environment organization */
	#define CONFIG_ENV_SIZE SZ_8K

	/*
	* If want to use nand, define CONFIG_NAND_MXS and rework board
	* to support nand, since emmc has pin conflicts with nand
	*/
	#ifdef CONFIG_NAND_MXS
	/* NAND stuff */
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE 0x40000000
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/* DMA stuff, needed for GPMI/MXS NAND support */
	#define CONFIG_APBH_DMA
	#define CONFIG_APBH_DMA_BURST
	#define CONFIG_APBH_DMA_BURST8
	#endif

	#define CONFIG_ENV_OFFSET (12 * SZ_64K)
	#ifdef CONFIG_NAND_MXS
	#define CONFIG_SYS_FSL_USDHC_NUM 1
	#else
	#define CONFIG_SYS_FSL_USDHC_NUM 2
	#endif

	#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1 */
	#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
	#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC1 */

	/* USB Configs */
	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)

	#define CONFIG_IMX_THERMAL

	#define CONFIG_USBD_HS

	#define CONFIG_USB_FUNCTION_MASS_STORAGE

	#ifdef CONFIG_VIDEO
	#define CONFIG_VIDEO_MXS
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_SPLASH_SCREEN_ALIGN
	#define CONFIG_BMP_16BPP
	#define CONFIG_VIDEO_BMP_RLE8
	#define CONFIG_VIDEO_BMP_LOGO
	#endif

	#ifdef CONFIG_FSL_QSPI
	#define CONFIG_SPI_FLASH
	#define CONFIG_SPI_FLASH_MACRONIX
	#define CONFIG_SPI_FLASH_BAR
	#define CONFIG_SF_DEFAULT_BUS 0
	#define CONFIG_SF_DEFAULT_CS 0
	#define CONFIG_SF_DEFAULT_SPEED 40000000
	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
	#define FSL_QSPI_FLASH_NUM 1
	#define FSL_QSPI_FLASH_SIZE SZ_64M
	#define QSPI0_BASE_ADDR QSPI1_IPS_BASE_ADDR
	#define QSPI0_AMBA_BASE QSPI0_ARB_BASE_ADDR
	#endif

	#endif /* __CONFIG_H */