| /* SPDX-License-Identifier: GPL-2.0+ */ | |
| /* | |
| * (C) Copyright 2009 | |
| * Net Insight <www.netinsight.net> | |
| * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> | |
| * | |
| * Based on sheevaplug.h: | |
| * (C) Copyright 2009 | |
| * Marvell Semiconductor <www.marvell.com> | |
| * Written-by: Prafulla Wadaskar <prafulla@marvell.com> | |
| */ | |
| #ifndef _CONFIG_OPENRD_H | |
| #define _CONFIG_OPENRD_H | |
| /* | |
| * High Level Configuration Options (easy to change) | |
| */ | |
| #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ | |
| #define CONFIG_KW88F6281 1 /* SOC Name */ | |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ | |
| /* | |
| * Commands configuration | |
| */ | |
| /* | |
| * mv-common.h should be defined after CMD configs since it used them | |
| * to enable certain macros | |
| */ | |
| #include "mv-common.h" | |
| /* | |
| * Environment variables configurations | |
| */ | |
| #ifdef CONFIG_CMD_NAND | |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ | |
| #endif | |
| /* | |
| * max 4k env size is enough, but in case of nand | |
| * it has to be rounded to sector size | |
| */ | |
| #define CONFIG_ENV_SIZE 0x20000 /* 128k */ | |
| #define CONFIG_ENV_OFFSET 0x80000 /* env starts here */ | |
| /* | |
| * Environment is right behind U-Boot in flash. Make sure U-Boot | |
| * doesn't grow into the environment area. | |
| */ | |
| #define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET | |
| /* | |
| * Default environment variables | |
| */ | |
| #define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \ | |
| "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ | |
| "${x_bootcmd_usb}; bootm 0x6400000;" | |
| #define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console=ttyS0,115200 " \ | |
| CONFIG_MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ | |
| "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ | |
| "x_bootcmd_usb=usb start\0" \ | |
| "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" | |
| /* | |
| * Ethernet Driver configuration | |
| */ | |
| #ifdef CONFIG_CMD_NET | |
| # ifdef CONFIG_BOARD_IS_OPENRD_BASE | |
| # define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ | |
| # else | |
| # define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ | |
| # endif | |
| # ifdef CONFIG_BOARD_IS_OPENRD_ULTIMATE | |
| # define CONFIG_PHY_BASE_ADR 0x0 | |
| # define PHY_NO "88E1121" | |
| # else | |
| # define CONFIG_PHY_BASE_ADR 0x8 | |
| # define PHY_NO "88E1116" | |
| # endif | |
| #endif /* CONFIG_CMD_NET */ | |
| /* | |
| * SATA Driver configuration | |
| */ | |
| #ifdef CONFIG_MVSATA_IDE | |
| #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET | |
| #define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET | |
| #endif /*CONFIG_MVSATA_IDE*/ | |
| #ifdef CONFIG_CMD_MMC | |
| #define CONFIG_MVEBU_MMC | |
| #define CONFIG_SYS_MMC_BASE KW_SDIO_BASE | |
| #endif /* CONFIG_CMD_MMC */ | |
| #endif /* _CONFIG_OPENRD_BASE_H */ |