include/configs/cm_fx6.h - u-boot - Git at Google


            
            /* SPDX-License-Identifier: GPL-2.0+ */

            
            /*

            
             * Config file for Compulab CM-FX6 board

            
             *

            
             * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/

            
             *

            
             * Author: Nikita Kiryanov <nikita@compulab.co.il>

            
             */


            #ifndef __CONFIG_CM_FX6_H

            
            #define __CONFIG_CM_FX6_H


            #include "mx6_common.h"


            /* Machine config */

            
            #define CONFIG_SYS_LITTLE_ENDIAN

            
            #define CONFIG_MACH_TYPE		4273


            /* MMC */

            
            #define CONFIG_SYS_FSL_USDHC_NUM	3

            
            #define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR


            /* RAM */

            
            #define PHYS_SDRAM_1			MMDC0_ARB_BASE_ADDR

            
            #define PHYS_SDRAM_2			MMDC1_ARB_BASE_ADDR

            
            #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1

            
            #define CONFIG_SYS_MEMTEST_START	0x10000000

            
            #define CONFIG_SYS_MEMTEST_END		0x10010000

            
            #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR

            
            #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

            
            #define CONFIG_SYS_INIT_SP_OFFSET \

            
            	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

            
            #define CONFIG_SYS_INIT_SP_ADDR \

            
            	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)


            /* Serial console */

            
            #define CONFIG_MXC_UART

            
            #define CONFIG_MXC_UART_BASE		UART4_BASE

            
            #define CONFIG_SYS_BAUDRATE_TABLE	{9600, 19200, 38400, 57600, 115200}


            /* Environment */


            #ifndef CONFIG_SPL_BUILD

            
            #define CONFIG_EXTRA_ENV_SETTINGS \

            
            	"fdt_high=0xffffffff\0" \

            
            	"initrd_high=0xffffffff\0" \

            
            	"fdt_addr_r=0x18000000\0" \

            
            	"ramdisk_addr_r=0x13000000\0" \

            
            	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \

            
            	"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \

            
            	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \

            
            	"fdtfile=undefined\0" \

            
            	"stdin=serial,usbkbd\0" \

            
            	"stdout=serial,vga\0" \

            
            	"stderr=serial,vga\0" \

            
            	"panel=HDMI\0" \

            
            	"autoload=no\0" \

            
            	"uImage=uImage-cm-fx6\0" \

            
            	"zImage=zImage-cm-fx6\0" \

            
            	"kernel=uImage-cm-fx6\0" \

            
            	"dtb=cm-fx6.dtb\0" \

            
            	"console=ttymxc3,115200\0" \

            
            	"ethprime=FEC0\0" \

            
            	"video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \

            
            	"video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \

            
            	"doboot=bootm ${kernel_addr_r}\0" \

            
            	"doloadfdt=false\0" \

            
            	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \

            
            	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \

            
            	"setboottypez=setenv kernel ${zImage};" \

            
            		"setenv doboot bootz ${kernel_addr_r} - ${fdt_addr_r};" \

            
            		"setenv doloadfdt true;\0" \

            
            	"setboottypem=setenv kernel ${uImage};" \

            
            		"setenv doboot bootm ${kernel_addr_r};" \

            
            		"setenv doloadfdt false;\0"\

            
            	"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \

            
            	"sataroot=/dev/sda2 rw rootwait\0" \

            
            	"nandroot=/dev/mtdblock4 rw\0" \

            
            	"nandrootfstype=ubifs\0" \

            
            	"mmcargs=setenv bootargs console=${console} root=${mmcroot} " \

            
            		"${video} ${extrabootargs}\0" \

            
            	"sataargs=setenv bootargs console=${console} root=${sataroot} " \

            
            		"${video} ${extrabootargs}\0" \

            
            	"nandargs=setenv bootargs console=${console} " \

            
            		"root=${nandroot} " \

            
            		"rootfstype=${nandrootfstype} " \

            
            		"${video} ${extrabootargs}\0" \

            
            	"nandboot=if run nandloadkernel; then " \

            
            			"run nandloadfdt;" \

            
            			"run setboottypem;" \

            
            			"run storagebootcmd;" \

            
            			"run setboottypez;" \

            
            			"run storagebootcmd;" \

            
            		"fi;\0" \

            
            	"run_eboot=echo Starting EBOOT ...; "\

            
            		"mmc dev 2 && " \

            
            		"mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \

            
            	"loadkernel=load ${storagetype} ${storagedev} ${kernel_addr_r} ${kernel};\0"\

            
            	"loadfdt=load ${storagetype} ${storagedev} ${fdt_addr_r} ${dtb};\0" \

            
            	"nandloadkernel=nand read ${kernel_addr_r} 0 780000;\0" \

            
            	"nandloadfdt=nand read ${fdt_addr_r} 780000 80000;\0" \

            
            	"setupmmcboot=setenv storagetype mmc; setenv storagedev 2;\0" \

            
            	"setupsataboot=setenv storagetype sata; setenv storagedev 0;\0" \

            
            	"setupnandboot=setenv storagetype nand;\0" \

            
            	"storagebootcmd=echo Booting from ${storagetype} ...;" \

            
            			"run ${storagetype}args; run doboot;\0" \

            
            	"trybootk=if run loadkernel; then " \

            
            		"if ${doloadfdt}; then " \

            
            			"run loadfdt;" \

            
            		"fi;" \

            
            		"run storagebootcmd;" \

            
            		"fi;\0" \

            
            	"trybootsmz=" \

            
            		"run setboottypem;" \

            
            		"run trybootk;" \

            
            		"run setboottypez;" \

            
            		"run trybootk;\0" \

            
            	"legacy_bootcmd=" \

            
            		"run setupmmcboot;" \

            
            		"mmc dev ${storagedev};" \

            
            		"if mmc rescan; then " \

            
            			"run trybootsmz;" \

            
            		"fi;" \

            
            		"run setupsataboot;" \

            
            		"if sata init; then " \

            
            			"run trybootsmz;" \

            
            		"fi;" \

            
            		"run setupnandboot;" \

            
            		"run nandboot;\0" \

            
            	"findfdt="\

            
            		"if test $board_name = Utilite && test $board_rev = MX6Q ; then " \

            
            			"setenv fdtfile imx6q-utilite-pro.dtb; fi; " \

            
            		"if test $fdtfile = undefined; then " \

            
            			"echo WARNING: Could not determine dtb to use; fi; \0" \

            
            	BOOTENV


            #define BOOT_TARGET_DEVICES(func) \

            
            	func(USB, usb, 0) \

            
            	func(MMC, mmc, 2) \

            
            	func(SATA, sata, 0)


            #include <config_distro_bootcmd.h>

            
            #else

            
            #define CONFIG_EXTRA_ENV_SETTINGS

            
            #endif


            /* NAND */

            
            #ifndef CONFIG_SPL_BUILD

            
            #define CONFIG_SYS_NAND_BASE		0x40000000

            
            #define CONFIG_SYS_NAND_MAX_CHIPS	1

            
            #define CONFIG_SYS_MAX_NAND_DEVICE	1

            
            #define CONFIG_SYS_NAND_ONFI_DETECTION

            
            /* APBH DMA is required for NAND support */

            
            #endif


            /* Ethernet */

            
            #define CONFIG_FEC_MXC

            
            #define CONFIG_FEC_MXC_PHYADDR		0

            
            #define CONFIG_FEC_XCV_TYPE		RGMII

            
            #define IMX_FEC_BASE			ENET_BASE_ADDR

            
            #define CONFIG_PHY_ATHEROS

            
            #define CONFIG_ETHPRIME			"FEC0"

            
            #define CONFIG_ARP_TIMEOUT		200UL

            
            #define CONFIG_NET_RETRY_COUNT		5


            /* USB */

            
            #define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)

            
            #define CONFIG_MXC_USB_FLAGS		0

            
            #define CONFIG_USB_MAX_CONTROLLER_COUNT	2

            
            #define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */


            /* I2C */

            
            #define CONFIG_SYS_I2C

            
            #define CONFIG_SYS_I2C_MXC

            
            #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */

            
            #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */

            
            #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

            
            #define CONFIG_SYS_I2C_SPEED		100000

            
            #define CONFIG_SYS_MXC_I2C3_SPEED	400000


            #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50

            
            #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1

            
            #define CONFIG_SYS_I2C_EEPROM_BUS	2


            /* SATA */

            
            #define CONFIG_SYS_SATA_MAX_DEVICE	1

            
            #define CONFIG_LBA48

            
            #define CONFIG_DWC_AHSATA_PORT_ID	0

            
            #define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR


            /* Boot */

            
            #define CONFIG_SYS_BOOTMAPSZ	        (8 << 20)

            
            #define CONFIG_SERIAL_TAG


            /* misc */

            
            #define CONFIG_SYS_MALLOC_LEN			(10 * 1024 * 1024)


            /* SPL */

            
            #include "imx6_spl.h"


            /* Display */

            
            #define CONFIG_IMX_HDMI


            #define CONFIG_SPLASH_SCREEN

            
            #define CONFIG_SPLASH_SOURCE

            
            #define CONFIG_VIDEO_BMP_RLE8


            #define CONFIG_VIDEO_LOGO

            
            #define CONFIG_VIDEO_BMP_LOGO


            /* EEPROM */

            
            #define CONFIG_ENV_EEPROM_IS_ON_I2C

            
            #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1

            
            #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4

            
            #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5

            
            #define CONFIG_SYS_EEPROM_SIZE			256


            #endif	/* __CONFIG_CM_FX6_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Config file for Compulab CM-FX6 board
	*
	* Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
	*
	* Author: Nikita Kiryanov <nikita@compulab.co.il>
	*/

	#ifndef __CONFIG_CM_FX6_H
	#define __CONFIG_CM_FX6_H

	#include "mx6_common.h"

	/* Machine config */
	#define CONFIG_SYS_LITTLE_ENDIAN
	#define CONFIG_MACH_TYPE 4273

	/* MMC */
	#define CONFIG_SYS_FSL_USDHC_NUM 3
	#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR

	/* RAM */
	#define PHYS_SDRAM_1 MMDC0_ARB_BASE_ADDR
	#define PHYS_SDRAM_2 MMDC1_ARB_BASE_ADDR
	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_MEMTEST_START 0x10000000
	#define CONFIG_SYS_MEMTEST_END 0x10010000
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	/* Serial console */
	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART4_BASE
	#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}

	/* Environment */

	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_addr_r=0x18000000\0" \
	"ramdisk_addr_r=0x13000000\0" \
	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
	"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
	"fdtfile=undefined\0" \
	"stdin=serial,usbkbd\0" \
	"stdout=serial,vga\0" \
	"stderr=serial,vga\0" \
	"panel=HDMI\0" \
	"autoload=no\0" \
	"uImage=uImage-cm-fx6\0" \
	"zImage=zImage-cm-fx6\0" \
	"kernel=uImage-cm-fx6\0" \
	"dtb=cm-fx6.dtb\0" \
	"console=ttymxc3,115200\0" \
	"ethprime=FEC0\0" \
	"video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \
	"video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \
	"doboot=bootm ${kernel_addr_r}\0" \
	"doloadfdt=false\0" \
	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
	"setboottypez=setenv kernel ${zImage};" \
	"setenv doboot bootz ${kernel_addr_r} - ${fdt_addr_r};" \
	"setenv doloadfdt true;\0" \
	"setboottypem=setenv kernel ${uImage};" \
	"setenv doboot bootm ${kernel_addr_r};" \
	"setenv doloadfdt false;\0"\
	"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
	"sataroot=/dev/sda2 rw rootwait\0" \
	"nandroot=/dev/mtdblock4 rw\0" \
	"nandrootfstype=ubifs\0" \
	"mmcargs=setenv bootargs console=${console} root=${mmcroot} " \
	"${video} ${extrabootargs}\0" \
	"sataargs=setenv bootargs console=${console} root=${sataroot} " \
	"${video} ${extrabootargs}\0" \
	"nandargs=setenv bootargs console=${console} " \
	"root=${nandroot} " \
	"rootfstype=${nandrootfstype} " \
	"${video} ${extrabootargs}\0" \
	"nandboot=if run nandloadkernel; then " \
	"run nandloadfdt;" \
	"run setboottypem;" \
	"run storagebootcmd;" \
	"run setboottypez;" \
	"run storagebootcmd;" \
	"fi;\0" \
	"run_eboot=echo Starting EBOOT ...; "\
	"mmc dev 2 && " \
	"mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \
	"loadkernel=load ${storagetype} ${storagedev} ${kernel_addr_r} ${kernel};\0"\
	"loadfdt=load ${storagetype} ${storagedev} ${fdt_addr_r} ${dtb};\0" \
	"nandloadkernel=nand read ${kernel_addr_r} 0 780000;\0" \
	"nandloadfdt=nand read ${fdt_addr_r} 780000 80000;\0" \
	"setupmmcboot=setenv storagetype mmc; setenv storagedev 2;\0" \
	"setupsataboot=setenv storagetype sata; setenv storagedev 0;\0" \
	"setupnandboot=setenv storagetype nand;\0" \
	"storagebootcmd=echo Booting from ${storagetype} ...;" \
	"run ${storagetype}args; run doboot;\0" \
	"trybootk=if run loadkernel; then " \
	"if ${doloadfdt}; then " \
	"run loadfdt;" \
	"fi;" \
	"run storagebootcmd;" \
	"fi;\0" \
	"trybootsmz=" \
	"run setboottypem;" \
	"run trybootk;" \
	"run setboottypez;" \
	"run trybootk;\0" \
	"legacy_bootcmd=" \
	"run setupmmcboot;" \
	"mmc dev ${storagedev};" \
	"if mmc rescan; then " \
	"run trybootsmz;" \
	"fi;" \
	"run setupsataboot;" \
	"if sata init; then " \
	"run trybootsmz;" \
	"fi;" \
	"run setupnandboot;" \
	"run nandboot;\0" \
	"findfdt="\
	"if test $board_name = Utilite && test $board_rev = MX6Q ; then " \
	"setenv fdtfile imx6q-utilite-pro.dtb; fi; " \
	"if test $fdtfile = undefined; then " \
	"echo WARNING: Could not determine dtb to use; fi; \0" \
	BOOTENV

	#define BOOT_TARGET_DEVICES(func) \
	func(USB, usb, 0) \
	func(MMC, mmc, 2) \
	func(SATA, sata, 0)

	#include <config_distro_bootcmd.h>
	#else
	#define CONFIG_EXTRA_ENV_SETTINGS
	#endif

	/* NAND */
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_SYS_NAND_BASE 0x40000000
	#define CONFIG_SYS_NAND_MAX_CHIPS 1
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_ONFI_DETECTION
	/* APBH DMA is required for NAND support */
	#endif

	/* Ethernet */
	#define CONFIG_FEC_MXC
	#define CONFIG_FEC_MXC_PHYADDR 0
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define IMX_FEC_BASE ENET_BASE_ADDR
	#define CONFIG_PHY_ATHEROS
	#define CONFIG_ETHPRIME "FEC0"
	#define CONFIG_ARP_TIMEOUT 200UL
	#define CONFIG_NET_RETRY_COUNT 5

	/* USB */
	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
	#define CONFIG_MXC_USB_FLAGS 0
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
	#define CONFIG_SYS_I2C_SPEED 100000
	#define CONFIG_SYS_MXC_I2C3_SPEED 400000

	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_I2C_EEPROM_BUS 2

	/* SATA */
	#define CONFIG_SYS_SATA_MAX_DEVICE 1
	#define CONFIG_LBA48
	#define CONFIG_DWC_AHSATA_PORT_ID 0
	#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR

	/* Boot */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
	#define CONFIG_SERIAL_TAG

	/* misc */
	#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)

	/* SPL */
	#include "imx6_spl.h"

	/* Display */
	#define CONFIG_IMX_HDMI

	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_SPLASH_SOURCE
	#define CONFIG_VIDEO_BMP_RLE8

	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_BMP_LOGO

	/* EEPROM */
	#define CONFIG_ENV_EEPROM_IS_ON_I2C
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
	#define CONFIG_SYS_EEPROM_SIZE 256

	#endif /* __CONFIG_CM_FX6_H */