| /* | |
| * Copyright (C) 2006 Atmel Corporation | |
| * | |
| * Copyright (C) 2012 Andreas Bießmann <andreas.devel@googlemail.com> | |
| * | |
| * Configuration settings for the AVR32 Network Gateway | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #ifndef __CONFIG_H | |
| #define __CONFIG_H | |
| #include <asm/arch/hardware.h> | |
| #define CONFIG_AT32AP | |
| #define CONFIG_AT32AP7000 | |
| #define CONFIG_ATNGW100MKII | |
| #define CONFIG_BOARD_EARLY_INIT_F | |
| #define CONFIG_BOARD_EARLY_INIT_R | |
| /* | |
| * Set up the PLL to run at 140 MHz, the CPU to run at the PLL | |
| * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency | |
| * and the PBA bus to run at 1/4 the PLL frequency. | |
| */ | |
| #define CONFIG_PLL | |
| #define CONFIG_SYS_POWER_MANAGER | |
| #define CONFIG_SYS_OSC0_HZ 20000000 | |
| #define CONFIG_SYS_PLL0_DIV 1 | |
| #define CONFIG_SYS_PLL0_MUL 7 | |
| #define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 | |
| /* | |
| * Set the CPU running at: | |
| * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz | |
| */ | |
| #define CONFIG_SYS_CLKDIV_CPU 0 | |
| /* | |
| * Set the HSB running at: | |
| * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz | |
| */ | |
| #define CONFIG_SYS_CLKDIV_HSB 1 | |
| /* | |
| * Set the PBA running at: | |
| * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz | |
| */ | |
| #define CONFIG_SYS_CLKDIV_PBA 2 | |
| /* | |
| * Set the PBB running at: | |
| * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz | |
| */ | |
| #define CONFIG_SYS_CLKDIV_PBB 1 | |
| /* Reserve VM regions for NOR flash, NAND flash and SDRAM */ | |
| #define CONFIG_SYS_NR_VM_REGIONS 3 | |
| /* | |
| * The PLLOPT register controls the PLL like this: | |
| * icp = PLLOPT<2> | |
| * ivco = PLLOPT<1:0> | |
| * | |
| * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). | |
| */ | |
| #define CONFIG_SYS_PLL0_OPT 0x04 | |
| #define CONFIG_USART_BASE ATMEL_BASE_USART1 | |
| #define CONFIG_USART_ID 1 | |
| /* User serviceable stuff */ | |
| #define CONFIG_DOS_PARTITION | |
| #define CONFIG_CMDLINE_TAG | |
| #define CONFIG_SETUP_MEMORY_TAGS | |
| #define CONFIG_INITRD_TAG | |
| #define CONFIG_STACKSIZE (2048) | |
| #define CONFIG_BAUDRATE 115200 | |
| #define CONFIG_BOOTARGS \ | |
| "root=mtd:main rootfstype=jffs2" | |
| #define CONFIG_BOOTCOMMAND \ | |
| "fsload 0x10400000 /uImage; bootm" | |
| #define CONFIG_BOOTDELAY 1 | |
| /* | |
| * After booting the board for the first time, new ethernet addresses | |
| * should be generated and assigned to the environment variables | |
| * "ethaddr" and "eth1addr". This is normally done during production. | |
| */ | |
| #define CONFIG_OVERWRITE_ETHADDR_ONCE | |
| /* | |
| * BOOTP/DHCP options | |
| */ | |
| #define CONFIG_BOOTP_SUBNETMASK | |
| #define CONFIG_BOOTP_GATEWAY | |
| /* | |
| * Command line configuration. | |
| */ | |
| #define CONFIG_CMD_ASKENV | |
| #define CONFIG_CMD_DHCP | |
| #define CONFIG_CMD_EXT2 | |
| #define CONFIG_CMD_FAT | |
| #define CONFIG_CMD_JFFS2 | |
| #define CONFIG_CMD_MMC | |
| #define CONFIG_CMD_SF | |
| #define CONFIG_CMD_SPI | |
| #define CONFIG_CMD_MII | |
| #define CONFIG_ATMEL_USART | |
| #define CONFIG_MACB | |
| #define CONFIG_PORTMUX_PIO | |
| #define CONFIG_SYS_NR_PIOS 5 | |
| #define CONFIG_SYS_HSDRAMC | |
| #define CONFIG_MMC | |
| #define CONFIG_GENERIC_ATMEL_MCI | |
| #define CONFIG_GENERIC_MMC | |
| #define CONFIG_ATMEL_SPI | |
| #define CONFIG_SYS_DCACHE_LINESZ 32 | |
| #define CONFIG_SYS_ICACHE_LINESZ 32 | |
| #define CONFIG_NR_DRAM_BANKS 1 | |
| #define CONFIG_SYS_FLASH_CFI | |
| #define CONFIG_FLASH_CFI_DRIVER | |
| #define CONFIG_SYS_FLASH_PROTECTION | |
| #define CONFIG_SYS_FLASH_BASE 0x00000000 | |
| #define CONFIG_SYS_FLASH_SIZE 0x800000 | |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 | |
| #define CONFIG_SYS_MAX_FLASH_SECT 135 | |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE | |
| #define CONFIG_SYS_TEXT_BASE 0x00000000 | |
| #define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE | |
| #define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE | |
| #define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE | |
| #define CONFIG_ENV_IS_IN_FLASH | |
| #define CONFIG_ENV_SIZE 65536 | |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) | |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) | |
| #define CONFIG_SYS_MALLOC_LEN (256*1024) | |
| /* Allow 4MB for the kernel run-time image */ | |
| #define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) | |
| #define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) | |
| /* Other configuration settings that shouldn't have to change all that often */ | |
| #define CONFIG_SYS_CBSIZE 256 | |
| #define CONFIG_SYS_MAXARGS 16 | |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) | |
| #define CONFIG_SYS_LONGHELP | |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE | |
| #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000) | |
| #define CONFIG_MTD_DEVICE | |
| #define CONFIG_MTD_PARTITIONS | |
| #endif /* __CONFIG_H */ |