| menu "Library routines" | |
| config ADDR_MAP | |
| bool "Enable support for non-identity virtual-physical mappings" | |
| help | |
| Enables helper code for implementing non-identity virtual-physical | |
| memory mappings for 32bit CPUs. | |
| This library only works in the post-relocation phase. | |
| config SYS_NUM_ADDR_MAP | |
| int "Size of the address-map table" | |
| depends on ADDR_MAP | |
| default 16 | |
| help | |
| Sets the number of entries in the virtual-physical mapping table. | |
| config PHYSMEM | |
| bool "Access to physical memory region (> 4G)" | |
| help | |
| Some basic support is provided for operations on memory not | |
| normally accessible to 32-bit U-Boot - e.g. some architectures | |
| support access to more than 4G of memory on 32-bit | |
| machines using physical address extension or similar. | |
| Enable this to access this basic support, which only supports clearing | |
| the memory. | |
| config BCH | |
| bool "Enable Software based BCH ECC" | |
| help | |
| Enables software based BCH ECC algorithm present in lib/bch.c | |
| This is used by SoC platforms which do not have built-in ELM | |
| hardware engine required for BCH ECC correction. | |
| config BINMAN_FDT | |
| bool "Allow access to binman information in the device tree" | |
| depends on BINMAN && DM && OF_CONTROL | |
| default y if OF_SEPARATE || OF_EMBED | |
| help | |
| This enables U-Boot to access information about binman entries, | |
| stored in the device tree in a binman node. Typical uses are to | |
| locate entries in the firmware image. See binman.h for the available | |
| functionality. | |
| config CC_OPTIMIZE_LIBS_FOR_SPEED | |
| bool "Optimize libraries for speed" | |
| help | |
| Enabling this option will pass "-O2" to gcc when compiling | |
| under "lib" directory. | |
| If unsure, say N. | |
| config CHARSET | |
| bool | |
| config DYNAMIC_CRC_TABLE | |
| bool "Enable Dynamic tables for CRC" | |
| help | |
| Enable this option to calculate entries for CRC tables at runtime. | |
| This can be helpful when reducing the size of the build image | |
| config HAVE_ARCH_IOMAP | |
| bool | |
| help | |
| Enable this option if architecture provides io{read,write}{8,16,32} | |
| I/O accessor functions. | |
| config HAVE_PRIVATE_LIBGCC | |
| bool | |
| config LIB_UUID | |
| bool | |
| config PRINTF | |
| bool | |
| default y | |
| config SPL_PRINTF | |
| bool | |
| select SPL_SPRINTF | |
| select SPL_STRTO if !SPL_USE_TINY_PRINTF | |
| config TPL_PRINTF | |
| bool | |
| select TPL_SPRINTF | |
| select TPL_STRTO if !TPL_USE_TINY_PRINTF | |
| config VPL_PRINTF | |
| bool | |
| select VPL_SPRINTF | |
| select VPL_STRTO if !VPL_USE_TINY_PRINTF | |
| config SPRINTF | |
| bool | |
| default y | |
| config SPL_SPRINTF | |
| bool | |
| config TPL_SPRINTF | |
| bool | |
| config VPL_SPRINTF | |
| bool | |
| config SSCANF | |
| bool | |
| config STRTO | |
| bool | |
| default y | |
| config SPL_STRTO | |
| bool | |
| config TPL_STRTO | |
| bool | |
| config VPL_STRTO | |
| bool | |
| config IMAGE_SPARSE | |
| bool | |
| config IMAGE_SPARSE_FILLBUF_SIZE | |
| hex "Android sparse image CHUNK_TYPE_FILL buffer size" | |
| default 0x80000 | |
| depends on IMAGE_SPARSE | |
| help | |
| Set the size of the fill buffer used when processing CHUNK_TYPE_FILL | |
| chunks. | |
| config USE_PRIVATE_LIBGCC | |
| bool "Use private libgcc" | |
| depends on HAVE_PRIVATE_LIBGCC | |
| default y if HAVE_PRIVATE_LIBGCC && ((ARM && !ARM64) || MIPS) | |
| help | |
| This option allows you to use the built-in libgcc implementation | |
| of U-Boot instead of the one provided by the compiler. | |
| If unsure, say N. | |
| config SYS_HZ | |
| int | |
| default 1000 | |
| help | |
| The frequency of the timer returned by get_timer(). | |
| get_timer() must operate in milliseconds and this option must be | |
| set to 1000. | |
| config SPL_USE_TINY_PRINTF | |
| bool "Enable tiny printf() version in SPL" | |
| depends on SPL | |
| default y | |
| help | |
| This option enables a tiny, stripped down printf version. | |
| This should only be used in space limited environments, | |
| like SPL versions with hard memory limits. This version | |
| reduces the code size by about 2.5KiB on armv7. | |
| The supported format specifiers are %c, %s, %u/%d and %x. | |
| config TPL_USE_TINY_PRINTF | |
| bool "Enable tiny printf() version in TPL" | |
| depends on TPL | |
| default y if SPL_USE_TINY_PRINTF | |
| help | |
| This option enables a tiny, stripped down printf version. | |
| This should only be used in space limited environments, | |
| like SPL versions with hard memory limits. This version | |
| reduces the code size by about 2.5KiB on armv7. | |
| The supported format specifiers are %c, %s, %u/%d and %x. | |
| config VPL_USE_TINY_PRINTF | |
| bool "Enable tiny printf() version for VPL" | |
| depends on VPL | |
| help | |
| This option enables a tiny, stripped down printf version. | |
| This should only be used in space limited environments, | |
| like SPL versions with hard memory limits. This version | |
| reduces the code size by about 2.5KiB on armv7. | |
| The supported format specifiers are %c, %s, %u/%d and %x. | |
| config PANIC_HANG | |
| bool "Do not reset the system on fatal error" | |
| help | |
| Define this option to stop the system in case of a fatal error, | |
| so that you have to reset it manually. This is probably NOT a good | |
| idea for an embedded system where you want the system to reboot | |
| automatically as fast as possible, but it may be useful during | |
| development since you can try to debug the conditions that lead to | |
| the situation. | |
| config REGEX | |
| bool "Enable regular expression support" | |
| default y if NET | |
| help | |
| If this variable is defined, U-Boot is linked against the | |
| SLRE (Super Light Regular Expression) library, which adds | |
| regex support to some commands, for example "env grep" and | |
| "setexpr". | |
| choice | |
| prompt "Pseudo-random library support type" | |
| depends on NET_RANDOM_ETHADDR || RANDOM_UUID || CMD_UUID || \ | |
| RNG_SANDBOX || UT_LIB && AES || FAT_WRITE | |
| default LIB_RAND | |
| help | |
| Select the library to provide pseudo-random number generator | |
| functions. LIB_HW_RAND supports certain hardware engines that | |
| provide this functionality. If in doubt, select LIB_RAND. | |
| config LIB_RAND | |
| bool "Pseudo-random library support" | |
| config LIB_HW_RAND | |
| bool "HW Engine for random library support" | |
| endchoice | |
| config SUPPORT_ACPI | |
| bool | |
| help | |
| Enable this if your arch or board can support generating ACPI | |
| (Advanced Configuration and Power Interface) tables. In this case | |
| U-Boot can generate these tables and pass them to the Operating | |
| System. | |
| config GENERATE_ACPI_TABLE | |
| bool "Generate an ACPI (Advanced Configuration and Power Interface) table" | |
| depends on SUPPORT_ACPI | |
| select QFW if QEMU | |
| help | |
| The Advanced Configuration and Power Interface (ACPI) specification | |
| provides an open standard for device configuration and management | |
| by the operating system. It defines platform-independent interfaces | |
| for configuration and power management monitoring. | |
| config SPL_TINY_MEMSET | |
| bool "Use a very small memset() in SPL" | |
| depends on SPL | |
| help | |
| The faster memset() is the arch-specific one (if available) enabled | |
| by CONFIG_USE_ARCH_MEMSET. If that is not enabled, we can still get | |
| better performance by writing a word at a time. But in very | |
| size-constrained environments even this may be too big. Enable this | |
| option to reduce code size slightly at the cost of some speed. | |
| config TPL_TINY_MEMSET | |
| bool "Use a very small memset() in TPL" | |
| depends on TPL | |
| help | |
| The faster memset() is the arch-specific one (if available) enabled | |
| by CONFIG_USE_ARCH_MEMSET. If that is not enabled, we can still get | |
| better performance by writing a word at a time. But in very | |
| size-constrained environments even this may be too big. Enable this | |
| option to reduce code size slightly at the cost of some speed. | |
| config RBTREE | |
| bool | |
| config BITREVERSE | |
| bool "Bit reverse library from Linux" | |
| config TRACE | |
| bool "Support for tracing of function calls and timing" | |
| imply CMD_TRACE | |
| select TIMER_EARLY | |
| help | |
| Enables function tracing within U-Boot. This allows recording of call | |
| traces including timing information. The command can write data to | |
| memory for exporting for analysis (e.g. using bootchart). | |
| See doc/README.trace for full details. | |
| config TRACE_BUFFER_SIZE | |
| hex "Size of trace buffer in U-Boot" | |
| depends on TRACE | |
| default 0x01000000 | |
| help | |
| Sets the size of the trace buffer in U-Boot. This is allocated from | |
| memory during relocation. If this buffer is too small, the trace | |
| history will be truncated, with later records omitted. | |
| If early trace is enabled (i.e. before relocation), this buffer must | |
| be large enough to include all the data from the early trace buffer as | |
| well, since this is copied over to the main buffer during relocation. | |
| A trace record is emitted for each function call and each record is | |
| 12 bytes (see struct trace_call). A suggested minimum size is 1MB. If | |
| the size is too small then 'trace stats' will show a message saying | |
| how many records were dropped due to buffer overflow. | |
| config TRACE_CALL_DEPTH_LIMIT | |
| int "Trace call depth limit" | |
| depends on TRACE | |
| default 15 | |
| help | |
| Sets the maximum call depth up to which function calls are recorded. | |
| config TRACE_EARLY | |
| bool "Enable tracing before relocation" | |
| depends on TRACE | |
| help | |
| Sometimes it is helpful to trace execution of U-Boot before | |
| relocation. This is possible by using a arch-specific, fixed buffer | |
| position in memory. Enable this option to start tracing as early as | |
| possible after U-Boot starts. | |
| config TRACE_EARLY_SIZE | |
| hex "Size of early trace buffer in U-Boot" | |
| depends on TRACE_EARLY | |
| default 0x00100000 | |
| help | |
| Sets the size of the early trace buffer in bytes. This is used to hold | |
| tracing information before relocation. | |
| config TRACE_EARLY_CALL_DEPTH_LIMIT | |
| int "Early trace call depth limit" | |
| depends on TRACE_EARLY | |
| default 200 | |
| help | |
| Sets the maximum call depth up to which function calls are recorded | |
| during early tracing. | |
| config TRACE_EARLY_ADDR | |
| hex "Address of early trace buffer in U-Boot" | |
| depends on TRACE_EARLY | |
| default 0x00100000 | |
| help | |
| Sets the address of the early trace buffer in U-Boot. This memory | |
| must be accessible before relocation. | |
| A trace record is emitted for each function call and each record is | |
| 12 bytes (see struct trace_call). A suggested minimum size is 1MB. If | |
| the size is too small then the message which says the amount of early | |
| data being coped will the the same as the | |
| config CIRCBUF | |
| bool "Enable circular buffer support" | |
| source lib/dhry/Kconfig | |
| menu "Security support" | |
| config AES | |
| bool "Support the AES algorithm" | |
| help | |
| This provides a means to encrypt and decrypt data using the AES | |
| (Advanced Encryption Standard). This algorithm uses a symetric key | |
| and is widely used as a streaming cipher. Different key lengths are | |
| supported by the algorithm but only a 128-bit key is supported at | |
| present. | |
| source lib/ecdsa/Kconfig | |
| source lib/rsa/Kconfig | |
| source lib/crypto/Kconfig | |
| source lib/crypt/Kconfig | |
| config TPM | |
| bool "Trusted Platform Module (TPM) Support" | |
| depends on DM | |
| imply DM_RNG | |
| help | |
| This enables support for TPMs which can be used to provide security | |
| features for your board. The TPM can be connected via LPC or I2C | |
| and a sandbox TPM is provided for testing purposes. Use the 'tpm' | |
| command to interactive the TPM. Driver model support is provided | |
| for the low-level TPM interface, but only one TPM is supported at | |
| a time by the TPM library. | |
| config SPL_TPM | |
| bool "Trusted Platform Module (TPM) Support in SPL" | |
| depends on SPL_DM | |
| help | |
| This enables support for TPMs which can be used to provide security | |
| features for your board. The TPM can be connected via LPC or I2C | |
| and a sandbox TPM is provided for testing purposes. Use the 'tpm' | |
| command to interactive the TPM. Driver model support is provided | |
| for the low-level TPM interface, but only one TPM is supported at | |
| a time by the TPM library. | |
| config TPL_TPM | |
| bool "Trusted Platform Module (TPM) Support in TPL" | |
| depends on TPL_DM | |
| help | |
| This enables support for TPMs which can be used to provide security | |
| features for your board. The TPM can be connected via LPC or I2C | |
| and a sandbox TPM is provided for testing purposes. Use the 'tpm' | |
| command to interactive the TPM. Driver model support is provided | |
| for the low-level TPM interface, but only one TPM is supported at | |
| a time by the TPM library. | |
| config VPL_TPM | |
| bool "Trusted Platform Module (TPM) Support in VPL" | |
| depends on VPL_DM | |
| help | |
| This enables support for TPMs which can be used to provide security | |
| features for your board. The TPM can be connected via LPC or I2C | |
| and a sandbox TPM is provided for testing purposes. Use the 'tpm' | |
| command to interactive the TPM. Driver model support is provided | |
| for the low-level TPM interface, but only one TPM is supported at | |
| a time by the TPM library. | |
| endmenu | |
| menu "Android Verified Boot" | |
| config LIBAVB | |
| bool "Android Verified Boot 2.0 support" | |
| depends on ANDROID_BOOT_IMAGE | |
| help | |
| This enables support of Android Verified Boot 2.0 which can be used | |
| to assure the end user of the integrity of the software running on a | |
| device. Introduces such features as boot chain of trust, rollback | |
| protection etc. | |
| endmenu | |
| menu "Hashing Support" | |
| config BLAKE2 | |
| bool "Enable BLAKE2 support" | |
| help | |
| This option enables support of hashing using BLAKE2B algorithm. | |
| The hash is calculated in software. | |
| The BLAKE2 algorithm produces a hash value (digest) between 1 and | |
| 64 bytes. | |
| config SHA1 | |
| bool "Enable SHA1 support" | |
| help | |
| This option enables support of hashing using SHA1 algorithm. | |
| The hash is calculated in software. | |
| The SHA1 algorithm produces a 160-bit (20-byte) hash value | |
| (digest). | |
| config SHA256 | |
| bool "Enable SHA256 support" | |
| help | |
| This option enables support of hashing using SHA256 algorithm. | |
| The hash is calculated in software. | |
| The SHA256 algorithm produces a 256-bit (32-byte) hash value | |
| (digest). | |
| config SHA512 | |
| bool "Enable SHA512 support" | |
| help | |
| This option enables support of hashing using SHA512 algorithm. | |
| The hash is calculated in software. | |
| The SHA512 algorithm produces a 512-bit (64-byte) hash value | |
| (digest). | |
| config SHA384 | |
| bool "Enable SHA384 support" | |
| select SHA512 | |
| help | |
| This option enables support of hashing using SHA384 algorithm. | |
| The hash is calculated in software. This is also selects SHA512, | |
| because these implementations share the bulk of the code.. | |
| The SHA384 algorithm produces a 384-bit (48-byte) hash value | |
| (digest). | |
| config SHA_HW_ACCEL | |
| bool "Enable hardware acceleration for SHA hash functions" | |
| help | |
| This option enables hardware acceleration for the SHA1 and SHA256 | |
| hashing algorithms. This affects the 'hash' command and also the | |
| hash_lookup_algo() function. | |
| if SPL | |
| config SPL_SHA1 | |
| bool "Enable SHA1 support in SPL" | |
| default y if SHA1 | |
| help | |
| This option enables support of hashing using SHA1 algorithm. | |
| The hash is calculated in software. | |
| The SHA1 algorithm produces a 160-bit (20-byte) hash value | |
| (digest). | |
| config SPL_SHA256 | |
| bool "Enable SHA256 support in SPL" | |
| default y if SHA256 | |
| help | |
| This option enables support of hashing using SHA256 algorithm. | |
| The hash is calculated in software. | |
| The SHA256 algorithm produces a 256-bit (32-byte) hash value | |
| (digest). | |
| config SPL_SHA512 | |
| bool "Enable SHA512 support in SPL" | |
| default y if SHA512 | |
| help | |
| This option enables support of hashing using SHA512 algorithm. | |
| The hash is calculated in software. | |
| The SHA512 algorithm produces a 512-bit (64-byte) hash value | |
| (digest). | |
| config SPL_SHA384 | |
| bool "Enable SHA384 support in SPL" | |
| default y if SHA384 | |
| select SPL_SHA512 | |
| help | |
| This option enables support of hashing using SHA384 algorithm. | |
| The hash is calculated in software. This is also selects SHA512, | |
| because these implementations share the bulk of the code.. | |
| The SHA384 algorithm produces a 384-bit (48-byte) hash value | |
| (digest). | |
| config SPL_SHA_HW_ACCEL | |
| bool "Enable hardware acceleration for SHA hash functions" | |
| default y if SHA_HW_ACCEL | |
| help | |
| This option enables hardware acceleration for the SHA1 and SHA256 | |
| hashing algorithms. This affects the 'hash' command and also the | |
| hash_lookup_algo() function. | |
| config SPL_SHA_PROG_HW_ACCEL | |
| bool "Enable Progressive hashing support using hardware in SPL" | |
| depends on SHA_PROG_HW_ACCEL | |
| default y | |
| help | |
| This option enables hardware-acceleration for SHA progressive | |
| hashing. | |
| Data can be streamed in a block at a time and the hashing is | |
| performed in hardware. | |
| endif | |
| if SHA_HW_ACCEL | |
| config SHA512_HW_ACCEL | |
| bool "Enable hardware acceleration for SHA512" | |
| depends on SHA512 | |
| help | |
| This option enables hardware acceleration for the SHA384 and SHA512 | |
| hashing algorithms. This affects the 'hash' command and also the | |
| hash_lookup_algo() function. | |
| config SHA_PROG_HW_ACCEL | |
| bool "Enable Progressive hashing support using hardware" | |
| help | |
| This option enables hardware-acceleration for SHA progressive | |
| hashing. | |
| Data can be streamed in a block at a time and the hashing is | |
| performed in hardware. | |
| endif | |
| config MD5 | |
| bool "Support MD5 algorithm" | |
| help | |
| This option enables MD5 support. MD5 is an algorithm designed | |
| in 1991 that produces a 16-byte digest (or checksum) from its input | |
| data. It has a number of vulnerabilities which preclude its use in | |
| security applications, but it can be useful for providing a quick | |
| checksum of a block of data. | |
| config SPL_MD5 | |
| bool "Support MD5 algorithm in SPL" | |
| depends on SPL | |
| help | |
| This option enables MD5 support in SPL. MD5 is an algorithm designed | |
| in 1991 that produces a 16-byte digest (or checksum) from its input | |
| data. It has a number of vulnerabilities which preclude its use in | |
| security applications, but it can be useful for providing a quick | |
| checksum of a block of data. | |
| config CRC32 | |
| def_bool y | |
| help | |
| Enables CRC32 support in U-Boot. This is normally required. | |
| config CRC32C | |
| bool | |
| config XXHASH | |
| bool | |
| endmenu | |
| menu "Compression Support" | |
| config LZ4 | |
| bool "Enable LZ4 decompression support" | |
| help | |
| If this option is set, support for LZ4 compressed images | |
| is included. The LZ4 algorithm can run in-place as long as the | |
| compressed image is loaded to the end of the output buffer, and | |
| trades lower compression ratios for much faster decompression. | |
| NOTE: This implements the release version of the LZ4 frame | |
| format as generated by default by the 'lz4' command line tool. | |
| This is not the same as the outdated, less efficient legacy | |
| frame format currently (2015) implemented in the Linux kernel | |
| (generated by 'lz4 -l'). The two formats are incompatible. | |
| config LZMA | |
| bool "Enable LZMA decompression support" | |
| help | |
| This enables support for LZMA (Lempel-Ziv-Markov chain algorithm), | |
| a dictionary compression algorithm that provides a high compression | |
| ratio and fairly fast decompression speed. See also | |
| CONFIG_CMD_LZMADEC which provides a decode command. | |
| config LZO | |
| bool "Enable LZO decompression support" | |
| help | |
| This enables support for the LZO compression algorithm. | |
| config GZIP | |
| bool "Enable gzip decompression support" | |
| select ZLIB | |
| default y | |
| help | |
| This enables support for GZIP compression algorithm. | |
| config ZLIB_UNCOMPRESS | |
| bool "Enables zlib's uncompress() functionality" | |
| help | |
| This enables an extra zlib functionality: the uncompress() function, | |
| which decompresses data from a buffer into another, knowing their | |
| sizes. Unlike gunzip(), there is no header parsing. | |
| config GZIP_COMPRESSED | |
| bool | |
| select ZLIB | |
| config BZIP2 | |
| bool "Enable bzip2 decompression support" | |
| help | |
| This enables support for BZIP2 compression algorithm. | |
| config ZLIB | |
| bool | |
| default y | |
| help | |
| This enables ZLIB compression lib. | |
| config ZSTD | |
| bool "Enable Zstandard decompression support" | |
| select XXHASH | |
| help | |
| This enables Zstandard decompression library. | |
| config SPL_LZ4 | |
| bool "Enable LZ4 decompression support in SPL" | |
| depends on SPL | |
| help | |
| This enables support for the LZ4 decompression algorithm in SPL. LZ4 | |
| is a lossless data compression algorithm that is focused on | |
| fast compression and decompression speed. It belongs to the LZ77 | |
| family of byte-oriented compression schemes. | |
| config SPL_LZMA | |
| bool "Enable LZMA decompression support for SPL build" | |
| depends on SPL | |
| help | |
| This enables support for LZMA compression algorithm for SPL boot. | |
| config VPL_LZMA | |
| bool "Enable LZMA decompression support for VPL build" | |
| default y if LZMA | |
| help | |
| This enables support for LZMA compression algorithm for VPL boot. | |
| config SPL_LZO | |
| bool "Enable LZO decompression support in SPL" | |
| depends on SPL | |
| help | |
| This enables support for LZO compression algorithm in the SPL. | |
| config SPL_GZIP | |
| bool "Enable gzip decompression support for SPL build" | |
| select SPL_ZLIB | |
| help | |
| This enables support for the GZIP compression algorithm for SPL boot. | |
| config SPL_ZLIB | |
| bool | |
| help | |
| This enables compression lib for SPL boot. | |
| config SPL_ZSTD | |
| bool "Enable Zstandard decompression support in SPL" | |
| depends on SPL | |
| select XXHASH | |
| help | |
| This enables Zstandard decompression library in the SPL. | |
| endmenu | |
| config ERRNO_STR | |
| bool "Enable function for getting errno-related string message" | |
| help | |
| The function errno_str(int errno), returns a pointer to the errno | |
| corresponding text message: | |
| - if errno is null or positive number - a pointer to "Success" message | |
| - if errno is negative - a pointer to errno related message | |
| config HEXDUMP | |
| bool "Enable hexdump" | |
| help | |
| This enables functions for printing dumps of binary data. | |
| config SPL_HEXDUMP | |
| bool "Enable hexdump in SPL" | |
| depends on SPL && HEXDUMP | |
| help | |
| This enables functions for printing dumps of binary data in | |
| SPL. | |
| config GETOPT | |
| bool "Enable getopt" | |
| help | |
| This enables functions for parsing command-line options. | |
| config OF_LIBFDT | |
| bool "Enable the FDT library" | |
| default y if OF_CONTROL | |
| help | |
| This enables the FDT library (libfdt). It provides functions for | |
| accessing binary device tree images in memory, such as adding and | |
| removing nodes and properties, scanning through the tree and finding | |
| particular compatible nodes. The library operates on a flattened | |
| version of the device tree. | |
| config OF_LIBFDT_ASSUME_MASK | |
| hex "Mask of conditions to assume for libfdt" | |
| depends on OF_LIBFDT || FIT | |
| default 0 | |
| help | |
| Use this to change the assumptions made by libfdt about the | |
| device tree it is working with. A value of 0 means that no assumptions | |
| are made, and libfdt is able to deal with malicious data. A value of | |
| 0xff means all assumptions are made and any invalid data may cause | |
| unsafe execution. See FDT_ASSUME_PERFECT, etc. in libfdt_internal.h | |
| config OF_LIBFDT_OVERLAY | |
| bool "Enable the FDT library overlay support" | |
| depends on OF_LIBFDT | |
| default y if ARCH_OMAP2PLUS || ARCH_KEYSTONE | |
| help | |
| This enables the FDT library (libfdt) overlay support. | |
| config SYS_FDT_PAD | |
| hex "Maximum size of the FDT memory area passeed to the OS" | |
| depends on OF_LIBFDT | |
| default 0x13000 if FMAN_ENET || QE || U_QE | |
| default 0x3000 | |
| help | |
| During OS boot, we allocate a region of memory within the bootmap | |
| for the FDT. This is the size that we will expand the FDT that we | |
| are using will be extended to be, in bytes. | |
| config SPL_OF_LIBFDT | |
| bool "Enable the FDT library for SPL" | |
| depends on SPL_LIBGENERIC_SUPPORT | |
| default y if SPL_OF_CONTROL | |
| help | |
| This enables the FDT library (libfdt). It provides functions for | |
| accessing binary device tree images in memory, such as adding and | |
| removing nodes and properties, scanning through the tree and finding | |
| particular compatible nodes. The library operates on a flattened | |
| version of the device tree. | |
| config SPL_OF_LIBFDT_ASSUME_MASK | |
| hex "Mask of conditions to assume for libfdt" | |
| depends on SPL_OF_LIBFDT || (FIT && SPL) | |
| default 0xff | |
| help | |
| Use this to change the assumptions made by libfdt in SPL about the | |
| device tree it is working with. A value of 0 means that no assumptions | |
| are made, and libfdt is able to deal with malicious data. A value of | |
| 0xff means all assumptions are made and any invalid data may cause | |
| unsafe execution. See FDT_ASSUME_PERFECT, etc. in libfdt_internal.h | |
| config TPL_OF_LIBFDT | |
| bool "Enable the FDT library for TPL" | |
| depends on TPL_LIBGENERIC_SUPPORT | |
| default y if TPL_OF_CONTROL | |
| help | |
| This enables the FDT library (libfdt). It provides functions for | |
| accessing binary device tree images in memory, such as adding and | |
| removing nodes and properties, scanning through the tree and finding | |
| particular compatible nodes. The library operates on a flattened | |
| version of the device tree. | |
| config TPL_OF_LIBFDT_ASSUME_MASK | |
| hex "Mask of conditions to assume for libfdt" | |
| depends on TPL_OF_LIBFDT || (FIT && TPL) | |
| default 0xff | |
| help | |
| Use this to change the assumptions made by libfdt in TPL about the | |
| device tree it is working with. A value of 0 means that no assumptions | |
| are made, and libfdt is able to deal with malicious data. A value of | |
| 0xff means all assumptions are made and any invalid data may cause | |
| unsafe execution. See FDT_ASSUME_PERFECT, etc. in libfdt_internal.h | |
| config VPL_OF_LIBFDT | |
| bool "Enable the FDT library for VPL" | |
| depends on VPL | |
| default y if VPL_OF_CONTROL && !VPL_OF_PLATDATA | |
| help | |
| This enables the FDT library (libfdt). It provides functions for | |
| accessing binary device tree images in memory, such as adding and | |
| removing nodes and properties, scanning through the tree and finding | |
| particular compatible nodes. The library operates on a flattened | |
| version of the device tree. | |
| config VPL_OF_LIBFDT_ASSUME_MASK | |
| hex "Mask of conditions to assume for libfdt" | |
| depends on VPL_OF_LIBFDT || (FIT && VPL) | |
| default 0xff | |
| help | |
| Use this to change the assumptions made by libfdt in SPL about the | |
| device tree it is working with. A value of 0 means that no assumptions | |
| are made, and libfdt is able to deal with malicious data. A value of | |
| 0xff means all assumptions are made and any invalid data may cause | |
| unsafe execution. See FDT_ASSUME_PERFECT, etc. in libfdt_internal.h | |
| config FDT_FIXUP_PARTITIONS | |
| bool "overwrite MTD partitions in DTS through defined in 'mtdparts'" | |
| depends on OF_LIBFDT | |
| depends on CMD_MTDPARTS | |
| help | |
| Allow overwriting defined partitions in the device tree blob | |
| using partition info defined in the 'mtdparts' environment | |
| variable. | |
| menu "System tables" | |
| depends on (!EFI && !SYS_COREBOOT) || (ARM && EFI_LOADER) | |
| config BLOBLIST_TABLES | |
| bool "Put tables in a bloblist" | |
| depends on X86 && BLOBLIST | |
| help | |
| Normally tables are placed at address 0xf0000 and can be up to 64KB | |
| long. With this option, tables are instead placed in the bloblist | |
| with a pointer from 0xf0000. The size can then be larger and the | |
| tables can be placed high in memory. | |
| config GENERATE_SMBIOS_TABLE | |
| bool "Generate an SMBIOS (System Management BIOS) table" | |
| default y | |
| depends on X86 || EFI_LOADER | |
| help | |
| The System Management BIOS (SMBIOS) specification addresses how | |
| motherboard and system vendors present management information about | |
| their products in a standard format by extending the BIOS interface | |
| on Intel architecture systems. | |
| Check http://www.dmtf.org/standards/smbios for details. | |
| See also SMBIOS_SYSINFO which allows SMBIOS values to be provided in | |
| the devicetree. | |
| config LIB_RATIONAL | |
| bool "enable continued fraction calculation routines" | |
| config SPL_LIB_RATIONAL | |
| bool "enable continued fraction calculation routines for SPL" | |
| depends on SPL | |
| endmenu | |
| config ASN1_COMPILER | |
| bool | |
| help | |
| ASN.1 (Abstract Syntax Notation One) is a standard interface | |
| description language for defining data structures that can be | |
| serialized and deserialized in a cross-platform way. It is | |
| broadly used in telecommunications and computer networking, | |
| and especially in cryptography (https://en.wikipedia.org/wiki/ASN.1). | |
| This option enables the support of the asn1 compiler. | |
| config ASN1_DECODER | |
| bool | |
| help | |
| ASN.1 (Abstract Syntax Notation One) is a standard interface | |
| description language for defining data structures that can be | |
| serialized and deserialized in a cross-platform way. It is | |
| broadly used in telecommunications and computer networking, | |
| and especially in cryptography (https://en.wikipedia.org/wiki/ASN.1). | |
| This option enables the support of the asn1 decoder. | |
| config SPL_ASN1_DECODER | |
| bool | |
| help | |
| ASN.1 (Abstract Syntax Notation One) is a standard interface | |
| description language for defining data structures that can be | |
| serialized and deserialized in a cross-platform way. It is | |
| broadly used in telecommunications and computer networking, | |
| and especially in cryptography (https://en.wikipedia.org/wiki/ASN.1). | |
| This option enables the support of the asn1 decoder in the SPL. | |
| config OID_REGISTRY | |
| bool | |
| help | |
| In computing, object identifiers or OIDs are an identifier mechanism | |
| standardized by the International Telecommunication Union (ITU) and | |
| ISO/IEC for naming any object, concept, or "thing" with a globally | |
| unambiguous persistent name (https://en.wikipedia.org/wiki/Object_identifier). | |
| Enable fast lookup object identifier registry. | |
| config SPL_OID_REGISTRY | |
| bool | |
| help | |
| In computing, object identifiers or OIDs are an identifier mechanism | |
| standardized by the International Telecommunication Union (ITU) and | |
| ISO/IEC for naming any object, concept, or "thing" with a globally | |
| unambiguous persistent name (https://en.wikipedia.org/wiki/Object_identifier). | |
| Enable fast lookup object identifier registry in the SPL. | |
| config SMBIOS_PARSER | |
| bool "SMBIOS parser" | |
| help | |
| A simple parser for SMBIOS data. | |
| source lib/efi/Kconfig | |
| source lib/efi_loader/Kconfig | |
| source lib/optee/Kconfig | |
| config TEST_FDTDEC | |
| bool "enable fdtdec test" | |
| depends on OF_LIBFDT | |
| config LIB_DATE | |
| bool | |
| config LIB_ELF | |
| bool | |
| help | |
| Support basic elf loading/validating functions. | |
| This supports for 32 bit and 64 bit versions. | |
| config LMB | |
| bool "Enable the logical memory blocks library (lmb)" | |
| default y if ARC || ARM || M68K || MICROBLAZE || MIPS || \ | |
| NIOS2 || PPC || RISCV || SANDBOX || SH || X86 || XTENSA | |
| help | |
| Support the library logical memory blocks. | |
| config LMB_USE_MAX_REGIONS | |
| bool "Use a common number of memory and reserved regions in lmb lib" | |
| depends on LMB | |
| default y | |
| help | |
| Define the number of supported memory regions in the library logical | |
| memory blocks. | |
| This feature allow to reduce the lmb library size by using compiler | |
| optimization when LMB_MEMORY_REGIONS == LMB_RESERVED_REGIONS. | |
| config LMB_MAX_REGIONS | |
| int "Number of memory and reserved regions in lmb lib" | |
| depends on LMB && LMB_USE_MAX_REGIONS | |
| default 8 | |
| help | |
| Define the number of supported regions, memory and reserved, in the | |
| library logical memory blocks. | |
| config LMB_MEMORY_REGIONS | |
| int "Number of memory regions in lmb lib" | |
| depends on LMB && !LMB_USE_MAX_REGIONS | |
| default 8 | |
| help | |
| Define the number of supported memory regions in the library logical | |
| memory blocks. | |
| The minimal value is CONFIG_NR_DRAM_BANKS. | |
| config LMB_RESERVED_REGIONS | |
| int "Number of reserved regions in lmb lib" | |
| depends on LMB && !LMB_USE_MAX_REGIONS | |
| default 8 | |
| help | |
| Define the number of supported reserved regions in the library logical | |
| memory blocks. | |
| endmenu | |
| menu "FWU Multi Bank Updates" | |
| source lib/fwu_updates/Kconfig | |
| endmenu |