| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * (C) Copyright 2011 | |
| * Heiko Schocher, DENX Software Engineering, hs@denx.de. | |
| * | |
| * Based on: | |
| * (C) Copyright 2009 | |
| * Stefano Babic, DENX Software Engineering, sbabic@denx.de. | |
| * | |
| * (C) Copyright 2008 | |
| * Marvell Semiconductor <www.marvell.com> | |
| * Written-by: Prafulla Wadaskar <prafulla@marvell.com> | |
| */ | |
| #include "imagetool.h" | |
| #include <image.h> | |
| #include "ublimage.h" | |
| /* | |
| * Supported commands for configuration file | |
| */ | |
| static table_entry_t ublimage_cmds[] = { | |
| {CMD_BOOT_MODE, "MODE", "UBL special modes", }, | |
| {CMD_ENTRY, "ENTRY", "Entry point addr for bootloader", }, | |
| {CMD_PAGE, "PAGES", | |
| "number of pages (size of bootloader)", }, | |
| {CMD_ST_BLOCK, "START_BLOCK", | |
| "block number where bootloader is present", }, | |
| {CMD_ST_PAGE, "START_PAGE", | |
| "page number where bootloader is present", }, | |
| {CMD_LD_ADDR, "LD_ADDR", | |
| "load addr", }, | |
| {-1, "", "", }, | |
| }; | |
| /* | |
| * Supported Boot options for configuration file | |
| * this is needed to set the correct flash offset | |
| */ | |
| static table_entry_t ublimage_bootops[] = { | |
| {UBL_MAGIC_SAFE, "safe", "Safe boot mode", }, | |
| {-1, "", "Invalid", }, | |
| }; | |
| static struct ubl_header ublimage_header; | |
| static uint32_t get_cfg_value(char *token, char *name, int linenr) | |
| { | |
| char *endptr; | |
| uint32_t value; | |
| errno = 0; | |
| value = strtoul(token, &endptr, 16); | |
| if (errno || (token == endptr)) { | |
| fprintf(stderr, "Error: %s[%d] - Invalid hex data(%s)\n", | |
| name, linenr, token); | |
| exit(EXIT_FAILURE); | |
| } | |
| return value; | |
| } | |
| static void print_hdr(struct ubl_header *ubl_hdr) | |
| { | |
| printf("Image Type : Davinci UBL Boot Image\n"); | |
| printf("UBL magic : %08x\n", ubl_hdr->magic); | |
| printf("Entry Point: %08x\n", ubl_hdr->entry); | |
| printf("nr of pages: %08x\n", ubl_hdr->pages); | |
| printf("start block: %08x\n", ubl_hdr->block); | |
| printf("start page : %08x\n", ubl_hdr->page); | |
| } | |
| static void parse_cfg_cmd(struct ubl_header *ublhdr, int32_t cmd, char *token, | |
| char *name, int lineno, int fld, int dcd_len) | |
| { | |
| static int cmd_ver_first = ~0; | |
| switch (cmd) { | |
| case CMD_BOOT_MODE: | |
| ublhdr->magic = get_table_entry_id(ublimage_bootops, | |
| "ublimage special boot mode", token); | |
| if (ublhdr->magic == -1) { | |
| fprintf(stderr, "Error: %s[%d] -Invalid boot mode" | |
| "(%s)\n", name, lineno, token); | |
| exit(EXIT_FAILURE); | |
| } | |
| ublhdr->magic += UBL_MAGIC_BASE; | |
| if (unlikely(cmd_ver_first != 1)) | |
| cmd_ver_first = 0; | |
| break; | |
| case CMD_ENTRY: | |
| ublhdr->entry = get_cfg_value(token, name, lineno); | |
| break; | |
| case CMD_PAGE: | |
| ublhdr->pages = get_cfg_value(token, name, lineno); | |
| break; | |
| case CMD_ST_BLOCK: | |
| ublhdr->block = get_cfg_value(token, name, lineno); | |
| break; | |
| case CMD_ST_PAGE: | |
| ublhdr->page = get_cfg_value(token, name, lineno); | |
| break; | |
| case CMD_LD_ADDR: | |
| ublhdr->pll_m = get_cfg_value(token, name, lineno); | |
| break; | |
| } | |
| } | |
| static void parse_cfg_fld(struct ubl_header *ublhdr, int32_t *cmd, | |
| char *token, char *name, int lineno, int fld, int *dcd_len) | |
| { | |
| switch (fld) { | |
| case CFG_COMMAND: | |
| *cmd = get_table_entry_id(ublimage_cmds, | |
| "ublimage commands", token); | |
| if (*cmd < 0) { | |
| fprintf(stderr, "Error: %s[%d] - Invalid command" | |
| "(%s)\n", name, lineno, token); | |
| exit(EXIT_FAILURE); | |
| } | |
| break; | |
| case CFG_REG_VALUE: | |
| parse_cfg_cmd(ublhdr, *cmd, token, name, lineno, fld, *dcd_len); | |
| break; | |
| default: | |
| break; | |
| } | |
| } | |
| static uint32_t parse_cfg_file(struct ubl_header *ublhdr, char *name) | |
| { | |
| FILE *fd = NULL; | |
| char *line = NULL; | |
| char *token, *saveptr1, *saveptr2; | |
| int lineno = 0; | |
| int i; | |
| char *ptr = (char *)ublhdr; | |
| int fld; | |
| size_t len; | |
| int dcd_len = 0; | |
| int32_t cmd; | |
| int ublhdrlen = sizeof(struct ubl_header); | |
| fd = fopen(name, "r"); | |
| if (fd == 0) { | |
| fprintf(stderr, "Error: %s - Can't open DCD file\n", name); | |
| exit(EXIT_FAILURE); | |
| } | |
| /* Fill header with 0xff */ | |
| for (i = 0; i < ublhdrlen; i++) { | |
| *ptr = 0xff; | |
| ptr++; | |
| } | |
| /* | |
| * Very simple parsing, line starting with # are comments | |
| * and are dropped | |
| */ | |
| while ((getline(&line, &len, fd)) > 0) { | |
| lineno++; | |
| token = strtok_r(line, "\r\n", &saveptr1); | |
| if (token == NULL) | |
| continue; | |
| /* Check inside the single line */ | |
| for (fld = CFG_COMMAND, cmd = CMD_INVALID, | |
| line = token; ; line = NULL, fld++) { | |
| token = strtok_r(line, " \t", &saveptr2); | |
| if (token == NULL) | |
| break; | |
| /* Drop all text starting with '#' as comments */ | |
| if (token[0] == '#') | |
| break; | |
| parse_cfg_fld(ublhdr, &cmd, token, name, | |
| lineno, fld, &dcd_len); | |
| } | |
| } | |
| fclose(fd); | |
| return dcd_len; | |
| } | |
| static int ublimage_check_image_types(uint8_t type) | |
| { | |
| if (type == IH_TYPE_UBLIMAGE) | |
| return EXIT_SUCCESS; | |
| else | |
| return EXIT_FAILURE; | |
| } | |
| static int ublimage_verify_header(unsigned char *ptr, int image_size, | |
| struct image_tool_params *params) | |
| { | |
| struct ubl_header *ubl_hdr = (struct ubl_header *)ptr; | |
| if ((ubl_hdr->magic & 0xFFFFFF00) != UBL_MAGIC_BASE) | |
| return -1; | |
| return 0; | |
| } | |
| static void ublimage_print_header(const void *ptr) | |
| { | |
| struct ubl_header *ubl_hdr = (struct ubl_header *) ptr; | |
| print_hdr(ubl_hdr); | |
| } | |
| static void ublimage_set_header(void *ptr, struct stat *sbuf, int ifd, | |
| struct image_tool_params *params) | |
| { | |
| struct ubl_header *ublhdr = (struct ubl_header *)ptr; | |
| /* Parse configuration file */ | |
| parse_cfg_file(ublhdr, params->imagename); | |
| } | |
| int ublimage_check_params(struct image_tool_params *params) | |
| { | |
| if (!params) | |
| return CFG_INVALID; | |
| if (!strlen(params->imagename)) { | |
| fprintf(stderr, "Error: %s - Configuration file not" | |
| "specified, it is needed for ublimage generation\n", | |
| params->cmdname); | |
| return CFG_INVALID; | |
| } | |
| /* | |
| * Check parameters: | |
| * XIP is not allowed and verify that incompatible | |
| * parameters are not sent at the same time | |
| * For example, if list is required a data image must not be provided | |
| */ | |
| return (params->dflag && (params->fflag || params->lflag)) || | |
| (params->fflag && (params->dflag || params->lflag)) || | |
| (params->lflag && (params->dflag || params->fflag)) || | |
| (params->xflag) || !(strlen(params->imagename)); | |
| } | |
| /* | |
| * ublimage parameters | |
| */ | |
| U_BOOT_IMAGE_TYPE( | |
| ublimage, | |
| "Davinci UBL boot support", | |
| sizeof(struct ubl_header), | |
| (void *)&ublimage_header, | |
| ublimage_check_params, | |
| ublimage_verify_header, | |
| ublimage_print_header, | |
| ublimage_set_header, | |
| NULL, | |
| ublimage_check_image_types, | |
| NULL, | |
| NULL | |
| ); |