| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Texas Instruments GPMC Driver | |
| * | |
| * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ | |
| */ | |
| #include <asm/io.h> | |
| #include <clk.h> | |
| #include <dm.h> | |
| #include <dm/device-internal.h> | |
| #include <dm/device_compat.h> | |
| #include <dm/devres.h> | |
| #include <dm/lists.h> | |
| #include <linux/mtd/omap_gpmc.h> | |
| #include <linux/ioport.h> | |
| #include <linux/io.h> | |
| #include <linux/sizes.h> | |
| #include "ti-gpmc.h" | |
| enum gpmc_clk_domain { | |
| GPMC_CD_FCLK, | |
| GPMC_CD_CLK | |
| }; | |
| struct gpmc_cs_data { | |
| const char *name; | |
| #define GPMC_CS_RESERVED BIT(0) | |
| u32 flags; | |
| }; | |
| struct ti_gpmc { | |
| void __iomem *base; | |
| u32 cs_num; | |
| u32 nr_waitpins; | |
| struct clk *l3_clk; | |
| u32 capability_flags; | |
| struct resource data; | |
| }; | |
| static struct gpmc_cs_data gpmc_cs[GPMC_CS_NUM]; | |
| static unsigned int gpmc_cs_num = GPMC_CS_NUM; | |
| static unsigned int gpmc_nr_waitpins; | |
| static unsigned int gpmc_capability; | |
| static void __iomem *gpmc_base; | |
| static struct clk *gpmc_l3_clk; | |
| /* Public, as required by nand/raw/omap_gpmc.c */ | |
| const struct gpmc *gpmc_cfg; | |
| /* | |
| * The first 1MB of GPMC address space is typically mapped to | |
| * the internal ROM. Never allocate the first page, to | |
| * facilitate bug detection; even if we didn't boot from ROM. | |
| * As GPMC minimum partition size is 16MB we can only start from | |
| * there. | |
| */ | |
| #define GPMC_MEM_START 0x1000000 | |
| #define GPMC_MEM_END 0x3FFFFFFF | |
| static void gpmc_write_reg(int idx, u32 val) | |
| { | |
| writel_relaxed(val, gpmc_base + idx); | |
| } | |
| static u32 gpmc_read_reg(int idx) | |
| { | |
| return readl_relaxed(gpmc_base + idx); | |
| } | |
| static void gpmc_cs_write_reg(int cs, int idx, u32 val) | |
| { | |
| void __iomem *reg_addr; | |
| reg_addr = gpmc_base + GPMC_CS0_OFFSET + (cs * GPMC_CS_SIZE) + idx; | |
| writel_relaxed(val, reg_addr); | |
| } | |
| static u32 gpmc_cs_read_reg(int cs, int idx) | |
| { | |
| void __iomem *reg_addr; | |
| reg_addr = gpmc_base + GPMC_CS0_OFFSET + (cs * GPMC_CS_SIZE) + idx; | |
| return readl_relaxed(reg_addr); | |
| } | |
| static unsigned long gpmc_get_fclk_period(void) | |
| { | |
| unsigned long rate = clk_get_rate(gpmc_l3_clk); | |
| rate /= 1000; | |
| rate = 1000000000 / rate; /* In picoseconds */ | |
| return rate; | |
| } | |
| /** | |
| * gpmc_get_clk_period - get period of selected clock domain in ps | |
| * @cs: Chip Select Region. | |
| * @cd: Clock Domain. | |
| * | |
| * GPMC_CS_CONFIG1 GPMCFCLKDIVIDER for cs has to be setup | |
| * prior to calling this function with GPMC_CD_CLK. | |
| */ | |
| static unsigned long gpmc_get_clk_period(int cs, enum gpmc_clk_domain cd) | |
| { | |
| unsigned long tick_ps = gpmc_get_fclk_period(); | |
| u32 l; | |
| int div; | |
| switch (cd) { | |
| case GPMC_CD_CLK: | |
| /* get current clk divider */ | |
| l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); | |
| div = (l & 0x03) + 1; | |
| /* get GPMC_CLK period */ | |
| tick_ps *= div; | |
| break; | |
| case GPMC_CD_FCLK: | |
| default: | |
| break; | |
| } | |
| return tick_ps; | |
| } | |
| static unsigned int gpmc_ns_to_clk_ticks(unsigned int time_ns, int cs, | |
| enum gpmc_clk_domain cd) | |
| { | |
| unsigned long tick_ps; | |
| /* Calculate in picosecs to yield more exact results */ | |
| tick_ps = gpmc_get_clk_period(cs, cd); | |
| return (time_ns * 1000 + tick_ps - 1) / tick_ps; | |
| } | |
| static unsigned int gpmc_ns_to_ticks(unsigned int time_ns) | |
| { | |
| return gpmc_ns_to_clk_ticks(time_ns, /* any CS */ 0, GPMC_CD_FCLK); | |
| } | |
| static unsigned int gpmc_ps_to_ticks(unsigned int time_ps) | |
| { | |
| unsigned long tick_ps; | |
| /* Calculate in picosecs to yield more exact results */ | |
| tick_ps = gpmc_get_fclk_period(); | |
| return (time_ps + tick_ps - 1) / tick_ps; | |
| } | |
| static __maybe_unused unsigned int gpmc_clk_ticks_to_ns(unsigned int ticks, int cs, | |
| enum gpmc_clk_domain cd) | |
| { | |
| return ticks * gpmc_get_clk_period(cs, cd) / 1000; | |
| } | |
| static inline void gpmc_cs_modify_reg(int cs, int reg, u32 mask, bool value) | |
| { | |
| u32 l; | |
| l = gpmc_cs_read_reg(cs, reg); | |
| if (value) | |
| l |= mask; | |
| else | |
| l &= ~mask; | |
| gpmc_cs_write_reg(cs, reg, l); | |
| } | |
| static void gpmc_cs_bool_timings(int cs, const struct gpmc_bool_timings *p) | |
| { | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG1, | |
| GPMC_CONFIG1_TIME_PARA_GRAN, | |
| p->time_para_granularity); | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG2, | |
| GPMC_CONFIG2_CSEXTRADELAY, p->cs_extra_delay); | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG3, | |
| GPMC_CONFIG3_ADVEXTRADELAY, p->adv_extra_delay); | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG4, | |
| GPMC_CONFIG4_OEEXTRADELAY, p->oe_extra_delay); | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG4, | |
| GPMC_CONFIG4_WEEXTRADELAY, p->we_extra_delay); | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG6, | |
| GPMC_CONFIG6_CYCLE2CYCLESAMECSEN, | |
| p->cycle2cyclesamecsen); | |
| gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG6, | |
| GPMC_CONFIG6_CYCLE2CYCLEDIFFCSEN, | |
| p->cycle2cyclediffcsen); | |
| } | |
| #if IS_ENABLED(CONFIG_TI_GPMC_DEBUG) | |
| /** | |
| * get_gpmc_timing_reg - read a timing parameter and print DTS settings for it. | |
| * @cs: Chip Select Region | |
| * @reg: GPMC_CS_CONFIGn register offset. | |
| * @st_bit: Start Bit | |
| * @end_bit: End Bit. Must be >= @st_bit. | |
| * @max: Maximum parameter value (before optional @shift). | |
| * If 0, maximum is as high as @st_bit and @end_bit allow. | |
| * @name: DTS node name, w/o "gpmc," | |
| * @cd: Clock Domain of timing parameter. | |
| * @shift: Parameter value left shifts @shift, which is then printed instead of value. | |
| * @raw: Raw Format Option. | |
| * raw format: gpmc,name = <value> | |
| * tick format: gpmc,name = <value> /‍* x ns -- y ns; x ticks *‍/ | |
| * Where x ns -- y ns result in the same tick value. | |
| * When @max is exceeded, "invalid" is printed inside comment. | |
| * @noval: Parameter values equal to 0 are not printed. | |
| * @return: Specified timing parameter (after optional @shift). | |
| * | |
| */ | |
| static int get_gpmc_timing_reg(/* timing specifiers */ | |
| int cs, int reg, int st_bit, int end_bit, int max, | |
| const char *name, const enum gpmc_clk_domain cd, | |
| /* value transform */ | |
| int shift, | |
| /* format specifiers */ | |
| bool raw, bool noval) | |
| { | |
| u32 l; | |
| int nr_bits; | |
| int mask; | |
| bool invalid; | |
| l = gpmc_cs_read_reg(cs, reg); | |
| nr_bits = end_bit - st_bit + 1; | |
| mask = (1 << nr_bits) - 1; | |
| l = (l >> st_bit) & mask; | |
| if (!max) | |
| max = mask; | |
| invalid = l > max; | |
| if (shift) | |
| l = (shift << l); | |
| if (noval && l == 0) | |
| return 0; | |
| if (!raw) { | |
| /* DTS tick format for timings in ns */ | |
| unsigned int time_ns; | |
| unsigned int time_ns_min = 0; | |
| if (l) | |
| time_ns_min = gpmc_clk_ticks_to_ns(l - 1, cs, cd) + 1; | |
| time_ns = gpmc_clk_ticks_to_ns(l, cs, cd); | |
| printf("gpmc,%s = <%u>; /* %u ns - %u ns; %i ticks%s*/\n", | |
| name, time_ns, time_ns_min, time_ns, l, | |
| invalid ? "; invalid " : " "); | |
| } else { | |
| /* raw format */ | |
| printf("gpmc,%s = <%u>;%s\n", name, l, | |
| invalid ? " /* invalid */" : ""); | |
| } | |
| return l; | |
| } | |
| #define GPMC_PRINT_CONFIG(cs, config) \ | |
| printf("CS%i %s: 0x%08x\n", cs, #config, \ | |
| gpmc_cs_read_reg(cs, config)) | |
| #define GPMC_GET_RAW(reg, st, end, field) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), 0, field, GPMC_CD_FCLK, 0, 1, 0) | |
| #define GPMC_GET_RAW_MAX(reg, st, end, max, field) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), (max), field, GPMC_CD_FCLK, 0, 1, 0) | |
| #define GPMC_GET_RAW_BOOL(reg, st, end, field) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), 0, field, GPMC_CD_FCLK, 0, 1, 1) | |
| #define GPMC_GET_RAW_SHIFT_MAX(reg, st, end, shift, max, field) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), (max), field, GPMC_CD_FCLK, (shift), 1, 1) | |
| #define GPMC_GET_TICKS(reg, st, end, field) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), 0, field, GPMC_CD_FCLK, 0, 0, 0) | |
| #define GPMC_GET_TICKS_CD(reg, st, end, field, cd) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), 0, field, (cd), 0, 0, 0) | |
| #define GPMC_GET_TICKS_CD_MAX(reg, st, end, max, field, cd) \ | |
| get_gpmc_timing_reg(cs, (reg), (st), (end), (max), field, (cd), 0, 0, 0) | |
| static void gpmc_show_regs(int cs, const char *desc) | |
| { | |
| printf("gpmc cs%i %s:\n", cs, desc); | |
| GPMC_PRINT_CONFIG(cs, GPMC_CS_CONFIG1); | |
| GPMC_PRINT_CONFIG(cs, GPMC_CS_CONFIG2); | |
| GPMC_PRINT_CONFIG(cs, GPMC_CS_CONFIG3); | |
| GPMC_PRINT_CONFIG(cs, GPMC_CS_CONFIG4); | |
| GPMC_PRINT_CONFIG(cs, GPMC_CS_CONFIG5); | |
| GPMC_PRINT_CONFIG(cs, GPMC_CS_CONFIG6); | |
| } | |
| /* | |
| * Note that gpmc,wait-pin handing wrongly assumes bit 8 is available, | |
| * see commit c9fb809. | |
| */ | |
| static void gpmc_cs_show_timings(int cs, const char *desc) | |
| { | |
| gpmc_show_regs(cs, desc); | |
| printf("gpmc cs%i access configuration:\n", cs); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 4, 4, "time-para-granularity"); | |
| GPMC_GET_RAW(GPMC_CS_CONFIG1, 8, 9, "mux-add-data"); | |
| GPMC_GET_RAW_SHIFT_MAX(GPMC_CS_CONFIG1, 12, 13, 1, | |
| GPMC_CONFIG1_DEVICESIZE_MAX, "device-width"); | |
| GPMC_GET_RAW(GPMC_CS_CONFIG1, 16, 17, "wait-pin"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 21, 21, "wait-on-write"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 22, 22, "wait-on-read"); | |
| GPMC_GET_RAW_SHIFT_MAX(GPMC_CS_CONFIG1, 23, 24, 4, | |
| GPMC_CONFIG1_ATTACHEDDEVICEPAGELENGTH_MAX, | |
| "burst-length"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 27, 27, "sync-write"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 28, 28, "burst-write"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 29, 29, "gpmc,sync-read"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 30, 30, "burst-read"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG1, 31, 31, "burst-wrap"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG2, 7, 7, "cs-extra-delay"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG3, 7, 7, "adv-extra-delay"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG4, 23, 23, "we-extra-delay"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG4, 7, 7, "oe-extra-delay"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG6, 7, 7, "cycle2cycle-samecsen"); | |
| GPMC_GET_RAW_BOOL(GPMC_CS_CONFIG6, 6, 6, "cycle2cycle-diffcsen"); | |
| printf("gpmc cs%i timings configuration:\n", cs); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG2, 0, 3, "cs-on-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG2, 8, 12, "cs-rd-off-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG2, 16, 20, "cs-wr-off-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG3, 0, 3, "adv-on-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG3, 8, 12, "adv-rd-off-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG3, 16, 20, "adv-wr-off-ns"); | |
| if (gpmc_capability & GPMC_HAS_MUX_AAD) { | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG3, 4, 6, "adv-aad-mux-on-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG3, 24, 26, | |
| "adv-aad-mux-rd-off-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG3, 28, 30, | |
| "adv-aad-mux-wr-off-ns"); | |
| } | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG4, 0, 3, "oe-on-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG4, 8, 12, "oe-off-ns"); | |
| if (gpmc_capability & GPMC_HAS_MUX_AAD) { | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG4, 4, 6, "oe-aad-mux-on-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG4, 13, 15, "oe-aad-mux-off-ns"); | |
| } | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG4, 16, 19, "we-on-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG4, 24, 28, "we-off-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG5, 0, 4, "rd-cycle-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG5, 8, 12, "wr-cycle-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG5, 16, 20, "access-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG5, 24, 27, "page-burst-access-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG6, 0, 3, "bus-turnaround-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG6, 8, 11, "cycle2cycle-delay-ns"); | |
| GPMC_GET_TICKS_CD_MAX(GPMC_CS_CONFIG1, 18, 19, | |
| GPMC_CONFIG1_WAITMONITORINGTIME_MAX, | |
| "wait-monitoring-ns", GPMC_CD_CLK); | |
| GPMC_GET_TICKS_CD_MAX(GPMC_CS_CONFIG1, 25, 26, | |
| GPMC_CONFIG1_CLKACTIVATIONTIME_MAX, | |
| "clk-activation-ns", GPMC_CD_FCLK); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG6, 16, 19, "wr-data-mux-bus-ns"); | |
| GPMC_GET_TICKS(GPMC_CS_CONFIG6, 24, 28, "wr-access-ns"); | |
| } | |
| #else | |
| static inline void gpmc_cs_show_timings(int cs, const char *desc) | |
| { | |
| } | |
| #endif | |
| /** | |
| * set_gpmc_timing_reg - set a single timing parameter for Chip Select Region. | |
| * Caller is expected to have initialized CONFIG1 GPMCFCLKDIVIDER | |
| * prior to calling this function with @cd equal to GPMC_CD_CLK. | |
| * | |
| * @cs: Chip Select Region. | |
| * @reg: GPMC_CS_CONFIGn register offset. | |
| * @st_bit: Start Bit | |
| * @end_bit: End Bit. Must be >= @st_bit. | |
| * @max: Maximum parameter value. | |
| * If 0, maximum is as high as @st_bit and @end_bit allow. | |
| * @time: Timing parameter in ns. | |
| * @cd: Timing parameter clock domain. | |
| * @name: Timing parameter name. | |
| * @return: 0 on success, -1 on error. | |
| */ | |
| static int set_gpmc_timing_reg(int cs, int reg, int st_bit, int end_bit, int max, | |
| int time, enum gpmc_clk_domain cd, const char *name) | |
| { | |
| u32 l; | |
| int ticks, mask, nr_bits; | |
| if (time == 0) | |
| ticks = 0; | |
| else | |
| ticks = gpmc_ns_to_clk_ticks(time, cs, cd); | |
| nr_bits = end_bit - st_bit + 1; | |
| mask = (1 << nr_bits) - 1; | |
| if (!max) | |
| max = mask; | |
| if (ticks > max) { | |
| pr_err("%s: GPMC CS%d: %s %d ns, %d ticks > %d ticks\n", | |
| __func__, cs, name, time, ticks, max); | |
| return -1; | |
| } | |
| l = gpmc_cs_read_reg(cs, reg); | |
| if (IS_ENABLED(CONFIG_TI_GPMC_DEBUG)) { | |
| printf("GPMC CS%d: %-17s: %3d ticks, %3lu ns (was %3i ticks) %3d ns\n", | |
| cs, name, ticks, gpmc_get_clk_period(cs, cd) * ticks / 1000, | |
| (l >> st_bit) & mask, time); | |
| } | |
| l &= ~(mask << st_bit); | |
| l |= ticks << st_bit; | |
| gpmc_cs_write_reg(cs, reg, l); | |
| return 0; | |
| } | |
| /** | |
| * gpmc_calc_waitmonitoring_divider - calculate proper GPMCFCLKDIVIDER based on WAITMONITORINGTIME | |
| * WAITMONITORINGTIME will be _at least_ as long as desired, i.e. | |
| * read --> don't sample bus too early | |
| * write --> data is longer on bus | |
| * | |
| * Formula: | |
| * gpmc_clk_div + 1 = ceil(ceil(waitmonitoringtime_ns / gpmc_fclk_ns) | |
| * / waitmonitoring_ticks) | |
| * WAITMONITORINGTIME resulting in 0 or 1 tick with div = 1 are caught by | |
| * div <= 0 check. | |
| * | |
| * @wait_monitoring: WAITMONITORINGTIME in ns. | |
| * @return: -1 on failure to scale, else proper divider > 0. | |
| */ | |
| static int gpmc_calc_waitmonitoring_divider(unsigned int wait_monitoring) | |
| { | |
| int div = gpmc_ns_to_ticks(wait_monitoring); | |
| div += GPMC_CONFIG1_WAITMONITORINGTIME_MAX - 1; | |
| div /= GPMC_CONFIG1_WAITMONITORINGTIME_MAX; | |
| if (div > 4) | |
| return -1; | |
| if (div <= 0) | |
| div = 1; | |
| return div; | |
| } | |
| /** | |
| * gpmc_calc_divider - calculate GPMC_FCLK divider for sync_clk GPMC_CLK period. | |
| * @sync_clk: GPMC_CLK period in ps. | |
| * @return: Returns at least 1 if GPMC_FCLK can be divided to GPMC_CLK. | |
| * Else, returns -1. | |
| */ | |
| static int gpmc_calc_divider(unsigned int sync_clk) | |
| { | |
| int div = gpmc_ps_to_ticks(sync_clk); | |
| if (div > 4) | |
| return -1; | |
| if (div <= 0) | |
| div = 1; | |
| return div; | |
| } | |
| /** | |
| * gpmc_cs_set_timings - program timing parameters for Chip Select Region. | |
| * @cs: Chip Select Region. | |
| * @t: GPMC timing parameters. | |
| * @s: GPMC timing settings. | |
| * @return: 0 on success, -1 on error. | |
| */ | |
| static int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t, | |
| const struct gpmc_settings *s) | |
| { | |
| int div, ret; | |
| u32 l; | |
| div = gpmc_calc_divider(t->sync_clk); | |
| if (div < 0) | |
| return -EINVAL; | |
| /* | |
| * See if we need to change the divider for waitmonitoringtime. | |
| * | |
| * Calculate GPMCFCLKDIVIDER independent of gpmc,sync-clk-ps in DT for | |
| * pure asynchronous accesses, i.e. both read and write asynchronous. | |
| * However, only do so if WAITMONITORINGTIME is actually used, i.e. | |
| * either WAITREADMONITORING or WAITWRITEMONITORING is set. | |
| * | |
| * This statement must not change div to scale async WAITMONITORINGTIME | |
| * to protect mixed synchronous and asynchronous accesses. | |
| * | |
| * We raise an error later if WAITMONITORINGTIME does not fit. | |
| */ | |
| if (!s->sync_read && !s->sync_write && | |
| (s->wait_on_read || s->wait_on_write) | |
| ) { | |
| div = gpmc_calc_waitmonitoring_divider(t->wait_monitoring); | |
| if (div < 0) { | |
| pr_err("%s: waitmonitoringtime %3d ns too large for greatest gpmcfclkdivider.\n", | |
| __func__, | |
| t->wait_monitoring | |
| ); | |
| return -ENXIO; | |
| } | |
| } | |
| ret = 0; | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG2, 0, 3, 0, t->cs_on, | |
| GPMC_CD_FCLK, "cs_on"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG2, 8, 12, 0, t->cs_rd_off, | |
| GPMC_CD_FCLK, "cs_rd_off"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG2, 16, 20, 0, t->cs_wr_off, | |
| GPMC_CD_FCLK, "cs_wr_off"); | |
| if (ret) | |
| return -ENXIO; | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG3, 0, 3, 0, t->adv_on, | |
| GPMC_CD_FCLK, "adv_on"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG3, 8, 12, 0, t->adv_rd_off, | |
| GPMC_CD_FCLK, "adv_rd_off"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG3, 16, 20, 0, t->adv_wr_off, | |
| GPMC_CD_FCLK, "adv_wr_off"); | |
| if (ret) | |
| return -ENXIO; | |
| if (gpmc_capability & GPMC_HAS_MUX_AAD) { | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG3, 4, 6, 0, | |
| t->adv_aad_mux_on, GPMC_CD_FCLK, | |
| "adv_aad_mux_on"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG3, 24, 26, 0, | |
| t->adv_aad_mux_rd_off, GPMC_CD_FCLK, | |
| "adv_aad_mux_rd_off"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG3, 28, 30, 0, | |
| t->adv_aad_mux_wr_off, GPMC_CD_FCLK, | |
| "adv_aad_mux_wr_off"); | |
| if (ret) | |
| return -ENXIO; | |
| } | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG4, 0, 3, 0, t->oe_on, | |
| GPMC_CD_FCLK, "oe_on"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG4, 8, 12, 0, t->oe_off, | |
| GPMC_CD_FCLK, "oe_off"); | |
| if (gpmc_capability & GPMC_HAS_MUX_AAD) { | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG4, 4, 6, 0, | |
| t->oe_aad_mux_on, GPMC_CD_FCLK, | |
| "oe_aad_mux_on"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG4, 13, 15, 0, | |
| t->oe_aad_mux_off, GPMC_CD_FCLK, | |
| "oe_aad_mux_off"); | |
| } | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG4, 16, 19, 0, t->we_on, | |
| GPMC_CD_FCLK, "we_on"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG4, 24, 28, 0, t->we_off, | |
| GPMC_CD_FCLK, "we_off"); | |
| if (ret) | |
| return -ENXIO; | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG5, 0, 4, 0, t->rd_cycle, | |
| GPMC_CD_FCLK, "rd_cycle"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG5, 8, 12, 0, t->wr_cycle, | |
| GPMC_CD_FCLK, "wr_cycle"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG5, 16, 20, 0, t->access, | |
| GPMC_CD_FCLK, "access"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG5, 24, 27, 0, | |
| t->page_burst_access, GPMC_CD_FCLK, | |
| "page_burst_access"); | |
| if (ret) | |
| return -ENXIO; | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG6, 0, 3, 0, | |
| t->bus_turnaround, GPMC_CD_FCLK, | |
| "bus_turnaround"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG6, 8, 11, 0, | |
| t->cycle2cycle_delay, GPMC_CD_FCLK, | |
| "cycle2cycle_delay"); | |
| if (ret) | |
| return -ENXIO; | |
| if (gpmc_capability & GPMC_HAS_WR_DATA_MUX_BUS) { | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG6, 16, 19, 0, | |
| t->wr_data_mux_bus, GPMC_CD_FCLK, | |
| "wr_data_mux_bus"); | |
| if (ret) | |
| return -ENXIO; | |
| } | |
| if (gpmc_capability & GPMC_HAS_WR_ACCESS) { | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG6, 24, 28, 0, | |
| t->wr_access, GPMC_CD_FCLK, | |
| "wr_access"); | |
| if (ret) | |
| return -ENXIO; | |
| } | |
| l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); | |
| l &= ~0x03; | |
| l |= (div - 1); | |
| gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, l); | |
| ret = 0; | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG1, 18, 19, | |
| GPMC_CONFIG1_WAITMONITORINGTIME_MAX, | |
| t->wait_monitoring, GPMC_CD_CLK, | |
| "wait_monitoring"); | |
| ret |= set_gpmc_timing_reg(cs, GPMC_CS_CONFIG1, 25, 26, | |
| GPMC_CONFIG1_CLKACTIVATIONTIME_MAX, | |
| t->clk_activation, GPMC_CD_FCLK, | |
| "clk_activation"); | |
| if (ret) | |
| return -ENXIO; | |
| if (IS_ENABLED(CONFIG_TI_GPMC_DEBUG)) { | |
| printf("GPMC CS%d CLK period is %lu ns (div %d)\n", | |
| cs, (div * gpmc_get_fclk_period()) / 1000, div); | |
| } | |
| gpmc_cs_bool_timings(cs, &t->bool_timings); | |
| gpmc_cs_show_timings(cs, "after gpmc_set_timings"); | |
| return 0; | |
| } | |
| static int gpmc_cs_set_memconf(int cs, resource_size_t base, u32 size) | |
| { | |
| u32 l; | |
| u32 mask; | |
| /* | |
| * Ensure that base address is aligned on a | |
| * boundary equal to or greater than size. | |
| */ | |
| if (base & (size - 1)) | |
| return -EINVAL; | |
| base >>= GPMC_CHUNK_SHIFT; | |
| mask = (1 << GPMC_SECTION_SHIFT) - size; | |
| mask >>= GPMC_CHUNK_SHIFT; | |
| mask <<= GPMC_CONFIG7_MASKADDRESS_OFFSET; | |
| l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7); | |
| l &= ~GPMC_CONFIG7_MASK; | |
| l |= base & GPMC_CONFIG7_BASEADDRESS_MASK; | |
| l |= mask & GPMC_CONFIG7_MASKADDRESS_MASK; | |
| l |= GPMC_CONFIG7_CSVALID; | |
| gpmc_cs_write_reg(cs, GPMC_CS_CONFIG7, l); | |
| return 0; | |
| } | |
| static void gpmc_cs_enable_mem(int cs) | |
| { | |
| u32 l; | |
| l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7); | |
| l |= GPMC_CONFIG7_CSVALID; | |
| gpmc_cs_write_reg(cs, GPMC_CS_CONFIG7, l); | |
| } | |
| static void gpmc_cs_disable_mem(int cs) | |
| { | |
| u32 l; | |
| l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7); | |
| l &= ~GPMC_CONFIG7_CSVALID; | |
| gpmc_cs_write_reg(cs, GPMC_CS_CONFIG7, l); | |
| } | |
| static void gpmc_cs_set_reserved(int cs, int reserved) | |
| { | |
| struct gpmc_cs_data *gpmc = &gpmc_cs[cs]; | |
| gpmc->flags |= GPMC_CS_RESERVED; | |
| } | |
| static bool gpmc_cs_reserved(int cs) | |
| { | |
| struct gpmc_cs_data *gpmc = &gpmc_cs[cs]; | |
| return gpmc->flags & GPMC_CS_RESERVED; | |
| } | |
| static unsigned long gpmc_mem_align(unsigned long size) | |
| { | |
| int order; | |
| size = (size - 1) >> (GPMC_CHUNK_SHIFT - 1); | |
| order = GPMC_CHUNK_SHIFT - 1; | |
| do { | |
| size >>= 1; | |
| order++; | |
| } while (size); | |
| size = 1 << order; | |
| return size; | |
| } | |
| static int gpmc_cs_request(ofnode node, int cs, struct resource *res) | |
| { | |
| int r = -1; | |
| u32 size; | |
| resource_size_t addr_base = res->start; | |
| if (cs >= gpmc_cs_num) { | |
| pr_err("%s: requested chip-select is disabled\n", __func__); | |
| return -ENODEV; | |
| } | |
| size = gpmc_mem_align(resource_size(res)); | |
| if (size > (1 << GPMC_SECTION_SHIFT)) | |
| return -ENOMEM; | |
| if (gpmc_cs_reserved(cs)) { | |
| r = -EBUSY; | |
| goto out; | |
| } | |
| if (addr_base & (SZ_16M - 1)) { | |
| pr_err("CS region should be aligned to 16M boundary\n"); | |
| goto out; | |
| } | |
| /* Disable CS while changing base address and size mask */ | |
| gpmc_cs_disable_mem(cs); | |
| r = gpmc_cs_set_memconf(cs, addr_base, size); | |
| if (r < 0) | |
| goto out; | |
| /* Enable CS */ | |
| gpmc_cs_enable_mem(cs); | |
| gpmc_cs_set_reserved(cs, 1); | |
| out: | |
| return r; | |
| } | |
| static void gpmc_cs_free(int cs) | |
| { | |
| if (cs >= gpmc_cs_num || cs < 0 || !gpmc_cs_reserved(cs)) { | |
| pr_warn("Trying to free non-reserved GPMC CS%d\n", cs); | |
| return; | |
| } | |
| gpmc_cs_disable_mem(cs); | |
| gpmc_cs_set_reserved(cs, 0); | |
| } | |
| /** | |
| * gpmc_configure - write request to configure gpmc | |
| * @cmd: command type | |
| * @wval: value to write | |
| * @return status of the operation | |
| */ | |
| static int gpmc_configure(int cmd, int wval) | |
| { | |
| u32 regval; | |
| switch (cmd) { | |
| case GPMC_CONFIG_WP: | |
| regval = gpmc_read_reg(GPMC_CONFIG); | |
| if (wval) | |
| regval &= ~GPMC_CONFIG_WRITEPROTECT; /* WP is ON */ | |
| else | |
| regval |= GPMC_CONFIG_WRITEPROTECT; /* WP is OFF */ | |
| gpmc_write_reg(GPMC_CONFIG, regval); | |
| break; | |
| default: | |
| pr_err("%s: command not supported\n", __func__); | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * gpmc_cs_program_settings - programs non-timing related settings | |
| * @cs: GPMC chip-select to program | |
| * @p: pointer to GPMC settings structure | |
| * | |
| * Programs non-timing related settings for a GPMC chip-select, such as | |
| * bus-width, burst configuration, etc. Function should be called once | |
| * for each chip-select that is being used and must be called before | |
| * calling gpmc_cs_set_timings() as timing parameters in the CONFIG1 | |
| * register will be initialised to zero by this function. Returns 0 on | |
| * success and appropriate negative error code on failure. | |
| */ | |
| static int gpmc_cs_program_settings(int cs, struct gpmc_settings *p) | |
| { | |
| u32 config1; | |
| if (!p->device_width || p->device_width > GPMC_DEVWIDTH_16BIT) { | |
| pr_err("%s: invalid width %d!", __func__, p->device_width); | |
| return -EINVAL; | |
| } | |
| /* Address-data multiplexing not supported for NAND devices */ | |
| if (p->device_nand && p->mux_add_data) { | |
| pr_err("%s: invalid configuration!\n", __func__); | |
| return -EINVAL; | |
| } | |
| if (p->mux_add_data > GPMC_MUX_AD || | |
| (p->mux_add_data == GPMC_MUX_AAD && | |
| !(gpmc_capability & GPMC_HAS_MUX_AAD))) { | |
| pr_err("%s: invalid multiplex configuration!\n", __func__); | |
| return -EINVAL; | |
| } | |
| /* Page/burst mode supports lengths of 4, 8 and 16 bytes */ | |
| if (p->burst_read || p->burst_write) { | |
| switch (p->burst_len) { | |
| case GPMC_BURST_4: | |
| case GPMC_BURST_8: | |
| case GPMC_BURST_16: | |
| break; | |
| default: | |
| pr_err("%s: invalid page/burst-length (%d)\n", | |
| __func__, p->burst_len); | |
| return -EINVAL; | |
| } | |
| } | |
| if (p->wait_pin > gpmc_nr_waitpins) { | |
| pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin); | |
| return -EINVAL; | |
| } | |
| config1 = GPMC_CONFIG1_DEVICESIZE((p->device_width - 1)); | |
| if (p->sync_read) | |
| config1 |= GPMC_CONFIG1_READTYPE_SYNC; | |
| if (p->sync_write) | |
| config1 |= GPMC_CONFIG1_WRITETYPE_SYNC; | |
| if (p->wait_on_read) | |
| config1 |= GPMC_CONFIG1_WAIT_READ_MON; | |
| if (p->wait_on_write) | |
| config1 |= GPMC_CONFIG1_WAIT_WRITE_MON; | |
| if (p->wait_on_read || p->wait_on_write) | |
| config1 |= GPMC_CONFIG1_WAIT_PIN_SEL(p->wait_pin); | |
| if (p->device_nand) | |
| config1 |= GPMC_CONFIG1_DEVICETYPE(GPMC_DEVICETYPE_NAND); | |
| if (p->mux_add_data) | |
| config1 |= GPMC_CONFIG1_MUXTYPE(p->mux_add_data); | |
| if (p->burst_read) | |
| config1 |= GPMC_CONFIG1_READMULTIPLE_SUPP; | |
| if (p->burst_write) | |
| config1 |= GPMC_CONFIG1_WRITEMULTIPLE_SUPP; | |
| if (p->burst_read || p->burst_write) { | |
| config1 |= GPMC_CONFIG1_PAGE_LEN(p->burst_len >> 3); | |
| config1 |= p->burst_wrap ? GPMC_CONFIG1_WRAPBURST_SUPP : 0; | |
| } | |
| gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, config1); | |
| return 0; | |
| } | |
| static void gpmc_cs_set_name(int cs, const char *name) | |
| { | |
| struct gpmc_cs_data *gpmc = &gpmc_cs[cs]; | |
| gpmc->name = name; | |
| } | |
| static const char *gpmc_cs_get_name(int cs) | |
| { | |
| struct gpmc_cs_data *gpmc = &gpmc_cs[cs]; | |
| return gpmc->name; | |
| } | |
| /** | |
| * gpmc_read_settings_dt - read gpmc settings from device-tree | |
| * @np: pointer to device-tree node for a gpmc child device | |
| * @p: pointer to gpmc settings structure | |
| * | |
| * Reads the GPMC settings for a GPMC child device from device-tree and | |
| * stores them in the GPMC settings structure passed. The GPMC settings | |
| * structure is initialised to zero by this function and so any | |
| * previously stored settings will be cleared. | |
| */ | |
| static void gpmc_read_settings_dt(ofnode np, struct gpmc_settings *p) | |
| { | |
| memset(p, 0, sizeof(struct gpmc_settings)); | |
| p->sync_read = ofnode_read_bool(np, "gpmc,sync-read"); | |
| p->sync_write = ofnode_read_bool(np, "gpmc,sync-write"); | |
| ofnode_read_u32(np, "gpmc,device-width", &p->device_width); | |
| ofnode_read_u32(np, "gpmc,mux-add-data", &p->mux_add_data); | |
| if (!ofnode_read_u32(np, "gpmc,burst-length", &p->burst_len)) { | |
| p->burst_wrap = ofnode_read_bool(np, "gpmc,burst-wrap"); | |
| p->burst_read = ofnode_read_bool(np, "gpmc,burst-read"); | |
| p->burst_write = ofnode_read_bool(np, "gpmc,burst-write"); | |
| if (!p->burst_read && !p->burst_write) | |
| pr_warn("%s: page/burst-length set but not used!\n", | |
| __func__); | |
| } | |
| if (!ofnode_read_u32(np, "gpmc,wait-pin", &p->wait_pin)) { | |
| p->wait_on_read = ofnode_read_bool(np, | |
| "gpmc,wait-on-read"); | |
| p->wait_on_write = ofnode_read_bool(np, | |
| "gpmc,wait-on-write"); | |
| if (!p->wait_on_read && !p->wait_on_write) | |
| pr_debug("%s: rd/wr wait monitoring not enabled!\n", | |
| __func__); | |
| } | |
| } | |
| static void gpmc_read_timings_dt(ofnode np, | |
| struct gpmc_timings *gpmc_t) | |
| { | |
| struct gpmc_bool_timings *p; | |
| if (!gpmc_t) | |
| return; | |
| memset(gpmc_t, 0, sizeof(*gpmc_t)); | |
| /* minimum clock period for syncronous mode */ | |
| ofnode_read_u32(np, "gpmc,sync-clk-ps", &gpmc_t->sync_clk); | |
| /* chip select timtings */ | |
| ofnode_read_u32(np, "gpmc,cs-on-ns", &gpmc_t->cs_on); | |
| ofnode_read_u32(np, "gpmc,cs-rd-off-ns", &gpmc_t->cs_rd_off); | |
| ofnode_read_u32(np, "gpmc,cs-wr-off-ns", &gpmc_t->cs_wr_off); | |
| /* ADV signal timings */ | |
| ofnode_read_u32(np, "gpmc,adv-on-ns", &gpmc_t->adv_on); | |
| ofnode_read_u32(np, "gpmc,adv-rd-off-ns", &gpmc_t->adv_rd_off); | |
| ofnode_read_u32(np, "gpmc,adv-wr-off-ns", &gpmc_t->adv_wr_off); | |
| ofnode_read_u32(np, "gpmc,adv-aad-mux-on-ns", | |
| &gpmc_t->adv_aad_mux_on); | |
| ofnode_read_u32(np, "gpmc,adv-aad-mux-rd-off-ns", | |
| &gpmc_t->adv_aad_mux_rd_off); | |
| ofnode_read_u32(np, "gpmc,adv-aad-mux-wr-off-ns", | |
| &gpmc_t->adv_aad_mux_wr_off); | |
| /* WE signal timings */ | |
| ofnode_read_u32(np, "gpmc,we-on-ns", &gpmc_t->we_on); | |
| ofnode_read_u32(np, "gpmc,we-off-ns", &gpmc_t->we_off); | |
| /* OE signal timings */ | |
| ofnode_read_u32(np, "gpmc,oe-on-ns", &gpmc_t->oe_on); | |
| ofnode_read_u32(np, "gpmc,oe-off-ns", &gpmc_t->oe_off); | |
| ofnode_read_u32(np, "gpmc,oe-aad-mux-on-ns", | |
| &gpmc_t->oe_aad_mux_on); | |
| ofnode_read_u32(np, "gpmc,oe-aad-mux-off-ns", | |
| &gpmc_t->oe_aad_mux_off); | |
| /* access and cycle timings */ | |
| ofnode_read_u32(np, "gpmc,page-burst-access-ns", | |
| &gpmc_t->page_burst_access); | |
| ofnode_read_u32(np, "gpmc,access-ns", &gpmc_t->access); | |
| ofnode_read_u32(np, "gpmc,rd-cycle-ns", &gpmc_t->rd_cycle); | |
| ofnode_read_u32(np, "gpmc,wr-cycle-ns", &gpmc_t->wr_cycle); | |
| ofnode_read_u32(np, "gpmc,bus-turnaround-ns", | |
| &gpmc_t->bus_turnaround); | |
| ofnode_read_u32(np, "gpmc,cycle2cycle-delay-ns", | |
| &gpmc_t->cycle2cycle_delay); | |
| ofnode_read_u32(np, "gpmc,wait-monitoring-ns", | |
| &gpmc_t->wait_monitoring); | |
| ofnode_read_u32(np, "gpmc,clk-activation-ns", | |
| &gpmc_t->clk_activation); | |
| /* only applicable to OMAP3+ */ | |
| ofnode_read_u32(np, "gpmc,wr-access-ns", &gpmc_t->wr_access); | |
| ofnode_read_u32(np, "gpmc,wr-data-mux-bus-ns", | |
| &gpmc_t->wr_data_mux_bus); | |
| /* bool timing parameters */ | |
| p = &gpmc_t->bool_timings; | |
| p->cycle2cyclediffcsen = | |
| ofnode_read_bool(np, "gpmc,cycle2cycle-diffcsen"); | |
| p->cycle2cyclesamecsen = | |
| ofnode_read_bool(np, "gpmc,cycle2cycle-samecsen"); | |
| p->we_extra_delay = ofnode_read_bool(np, "gpmc,we-extra-delay"); | |
| p->oe_extra_delay = ofnode_read_bool(np, "gpmc,oe-extra-delay"); | |
| p->adv_extra_delay = ofnode_read_bool(np, "gpmc,adv-extra-delay"); | |
| p->cs_extra_delay = ofnode_read_bool(np, "gpmc,cs-extra-delay"); | |
| p->time_para_granularity = | |
| ofnode_read_bool(np, "gpmc,time-para-granularity"); | |
| } | |
| /** | |
| * gpmc_probe_generic_child - configures the gpmc for a child device | |
| * @dev: pointer to gpmc platform device | |
| * @child: pointer to device-tree node for child device | |
| * | |
| * Allocates and configures a GPMC chip-select for a child device. | |
| * Returns 0 on success and appropriate negative error code on failure. | |
| */ | |
| static int gpmc_probe_generic_child(struct udevice *dev, | |
| ofnode child) | |
| { | |
| struct gpmc_settings gpmc_s; | |
| struct gpmc_timings gpmc_t; | |
| struct resource res; | |
| const char *name; | |
| int ret; | |
| u32 val, cs; | |
| if (ofnode_read_u32(child, "reg", &cs) < 0) { | |
| dev_err(dev, "can't get reg property of child %s\n", | |
| ofnode_get_name(child)); | |
| return -ENODEV; | |
| } | |
| if (ofnode_read_resource(child, 0, &res) < 0) { | |
| dev_err(dev, "%s has malformed 'reg' property\n", | |
| ofnode_get_name(child)); | |
| return -ENODEV; | |
| } | |
| /* | |
| * Check if we have multiple instances of the same device | |
| * on a single chip select. If so, use the already initialized | |
| * timings. | |
| */ | |
| name = gpmc_cs_get_name(cs); | |
| if (name && !strcmp(name, ofnode_get_name(child))) | |
| goto no_timings; | |
| ret = gpmc_cs_request(child, cs, &res); | |
| if (ret < 0) { | |
| dev_err(dev, "cannot request GPMC CS %d\n", cs); | |
| return ret; | |
| } | |
| gpmc_cs_set_name(cs, ofnode_get_name(child)); | |
| gpmc_read_settings_dt(child, &gpmc_s); | |
| gpmc_read_timings_dt(child, &gpmc_t); | |
| /* | |
| * For some GPMC devices we still need to rely on the bootloader | |
| * timings because the devices can be connected via FPGA. | |
| * REVISIT: Add timing support from slls644g.pdf. | |
| */ | |
| if (!gpmc_t.cs_rd_off) { | |
| pr_warn("enable GPMC debug to configure .dts timings for CS%i\n", | |
| cs); | |
| gpmc_cs_show_timings(cs, | |
| "please add GPMC bootloader timings to .dts"); | |
| goto no_timings; | |
| } | |
| /* CS must be disabled while making changes to gpmc configuration */ | |
| gpmc_cs_disable_mem(cs); | |
| if (!ofnode_read_u32(child, "nand-bus-width", &val)) { | |
| /* NAND specific setup */ | |
| ofnode_read_u32(child, "nand-bus-width", &val); | |
| switch (val) { | |
| case 8: | |
| gpmc_s.device_width = GPMC_DEVWIDTH_8BIT; | |
| break; | |
| case 16: | |
| gpmc_s.device_width = GPMC_DEVWIDTH_16BIT; | |
| break; | |
| default: | |
| dev_err(dev, "%s: invalid 'nand-bus-width'\n", | |
| ofnode_get_name(child)); | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| /* disable write protect */ | |
| gpmc_configure(GPMC_CONFIG_WP, 0); | |
| gpmc_s.device_nand = true; | |
| } else { | |
| ret = ofnode_read_u32(child, "bank-width", | |
| &gpmc_s.device_width); | |
| if (ret < 0 && !gpmc_s.device_width) { | |
| dev_err(dev, | |
| "%s has no 'gpmc,device-width' property\n", | |
| ofnode_get_name(child)); | |
| goto err; | |
| } | |
| } | |
| gpmc_cs_show_timings(cs, "before gpmc_cs_program_settings"); | |
| ret = gpmc_cs_program_settings(cs, &gpmc_s); | |
| if (ret < 0) | |
| goto err; | |
| ret = gpmc_cs_set_timings(cs, &gpmc_t, &gpmc_s); | |
| if (ret) { | |
| dev_err(dev, "failed to set gpmc timings for: %s\n", | |
| ofnode_get_name(child)); | |
| goto err; | |
| } | |
| /* Clear limited address i.e. enable A26-A11 */ | |
| val = gpmc_read_reg(GPMC_CONFIG); | |
| val &= ~GPMC_CONFIG_LIMITEDADDRESS; | |
| gpmc_write_reg(GPMC_CONFIG, val); | |
| /* Enable CS region */ | |
| gpmc_cs_enable_mem(cs); | |
| no_timings: | |
| return 0; | |
| err: | |
| gpmc_cs_free(cs); | |
| return ret; | |
| } | |
| static void gpmc_probe_dt_children(struct udevice *dev) | |
| { | |
| int ret; | |
| ofnode child; | |
| ofnode_for_each_subnode(child, dev_ofnode(dev)) { | |
| ret = gpmc_probe_generic_child(dev, child); | |
| if (ret) { | |
| dev_err(dev, "Cannot parse child %s:%d", | |
| ofnode_get_name(child), ret); | |
| } | |
| } | |
| } | |
| static int gpmc_parse_dt(struct udevice *dev, struct ti_gpmc *gpmc) | |
| { | |
| int ret; | |
| u32 val; | |
| ret = ofnode_read_u32(dev_ofnode(dev), "gpmc,num-cs", | |
| &val); | |
| if (ret < 0) { | |
| pr_err("%s: number of chip-selects not defined\n", __func__); | |
| return ret; | |
| } else if (val < 1) { | |
| pr_err("%s: all chip-selects are disabled\n", __func__); | |
| return -EINVAL; | |
| } else if (val > GPMC_CS_NUM) { | |
| pr_err("%s: number of supported chip-selects cannot be > %d\n", | |
| __func__, GPMC_CS_NUM); | |
| return -EINVAL; | |
| } | |
| gpmc->cs_num = val; | |
| gpmc_cs_num = val; | |
| ret = ofnode_read_u32(dev_ofnode(dev), "gpmc,num-waitpins", | |
| &gpmc->nr_waitpins); | |
| if (ret < 0) { | |
| pr_err("%s: number of wait pins not found!\n", __func__); | |
| return ret; | |
| } | |
| gpmc_nr_waitpins = gpmc->nr_waitpins; | |
| return 0; | |
| } | |
| static int gpmc_probe(struct udevice *dev) | |
| { | |
| struct ti_gpmc *priv = dev_get_priv(dev); | |
| int ret; | |
| struct resource res; | |
| ret = dev_read_resource_byname(dev, "cfg", &res); | |
| if (ret) { | |
| /* Legacy DT */ | |
| dev_read_resource(dev, 0, &res); | |
| priv->base = devm_ioremap(dev, res.start, resource_size(&res)); | |
| priv->data.start = GPMC_MEM_START; | |
| priv->data.end = GPMC_MEM_END; | |
| } else { | |
| priv->base = devm_ioremap(dev, res.start, resource_size(&res)); | |
| ret = dev_read_resource_byname(dev, "data", &res); | |
| if (ret) | |
| return -ENOENT; | |
| priv->data = res; | |
| } | |
| if (!priv->base) | |
| return -ENOMEM; | |
| gpmc_cfg = (struct gpmc *)priv->base; | |
| gpmc_base = priv->base; | |
| /* | |
| * Disable all IRQs as some bootroms might leave them enabled | |
| * and that will cause a lock-up later | |
| */ | |
| gpmc_write_reg(GPMC_IRQENABLE, 0); | |
| priv->l3_clk = devm_clk_get(dev, "fck"); | |
| if (IS_ERR(priv->l3_clk)) | |
| return PTR_ERR(priv->l3_clk); | |
| if (!clk_get_rate(priv->l3_clk)) | |
| return -EINVAL; | |
| gpmc_l3_clk = priv->l3_clk; | |
| ret = gpmc_parse_dt(dev, priv); | |
| if (ret) | |
| return ret; | |
| priv->capability_flags = dev->driver->of_match->data; | |
| gpmc_capability = priv->capability_flags; | |
| gpmc_probe_dt_children(dev); | |
| return 0; | |
| } | |
| #define GPMC_DATA_REV2_4 0 | |
| #define GPMC_DATA_REV5 (GPMC_HAS_WR_ACCESS | GPMC_HAS_WR_DATA_MUX_BUS) | |
| #define GPMC_DATA_REV6 (GPMC_HAS_WR_ACCESS | GPMC_HAS_WR_DATA_MUX_BUS | GPMC_HAS_MUX_AAD) | |
| static const struct udevice_id gpmc_dt_ids[] = { | |
| { .compatible = "ti,am64-gpmc", .data = GPMC_DATA_REV6, }, | |
| { .compatible = "ti,am3352-gpmc", .data = GPMC_DATA_REV5, }, | |
| { .compatible = "ti,omap2420-gpmc", .data = GPMC_DATA_REV2_4, }, | |
| { .compatible = "ti,omap2430-gpmc", .data = GPMC_DATA_REV2_4, }, | |
| { .compatible = "ti,omap3430-gpmc", .data = GPMC_DATA_REV5, }, | |
| { .compatible = "ti,omap4430-gpmc", .data = GPMC_DATA_REV6, }, | |
| { } /* sentinel */ | |
| }; | |
| U_BOOT_DRIVER(ti_gpmc) = { | |
| .name = "ti-gpmc", | |
| .id = UCLASS_MEMORY, | |
| .of_match = gpmc_dt_ids, | |
| .probe = gpmc_probe, | |
| .flags = DM_FLAG_ALLOC_PRIV_DMA, | |
| .priv_auto = sizeof(struct ti_gpmc), | |
| }; |