doc/device-tree-bindings/interrupt-controller/interrupts.txt

Specifying interrupt information for devices
============================================

1) Interrupt client nodes
-------------------------

Nodes that describe devices which generate interrupts must contain an
"interrupts" property, an "interrupts-extended" property, or both. If both are
present, the latter should take precedence; the former may be provided simply
for compatibility with software that does not recognize the latter. These
properties contain a list of interrupt specifiers, one per output interrupt. The
format of the interrupt specifier is determined by the interrupt controller to
which the interrupts are routed; see section 2 below for details.

  Example:
	interrupt-parent = <&intc1>;
	interrupts = <5 0>, <6 0>;

The "interrupt-parent" property is used to specify the controller to which
interrupts are routed and contains a single phandle referring to the interrupt
controller node. This property is inherited, so it may be specified in an
interrupt client node or in any of its parent nodes. Interrupts listed in the
"interrupts" property are always in reference to the node's interrupt parent.

The "interrupts-extended" property is a special form; useful when a node needs
to reference multiple interrupt parents or a different interrupt parent than
the inherited one. Each entry in this property contains both the parent phandle
and the interrupt specifier.

  Example:
	interrupts-extended = <&intc1 5 1>, <&intc2 1 0>;

(NOTE: only this 'special form' is supported in U-Boot)


2) Interrupt controller nodes
-----------------------------

A device is marked as an interrupt controller with the "interrupt-controller"
property. This is a empty, boolean property. An additional "#interrupt-cells"
property defines the number of cells needed to specify a single interrupt.

It is the responsibility of the interrupt controller's binding to define the
length and format of the interrupt specifier. The following two variants are
commonly used:

  a) one cell
  -----------
  The #interrupt-cells property is set to 1 and the single cell defines the
  index of the interrupt within the controller.

  Example:

	vic: intc@10140000 {
		compatible = "arm,versatile-vic";
		interrupt-controller;
		#interrupt-cells = <1>;
		reg = <0x10140000 0x1000>;
	};

	sic: intc@10003000 {
		compatible = "arm,versatile-sic";
		interrupt-controller;
		#interrupt-cells = <1>;
		reg = <0x10003000 0x1000>;
		interrupt-parent = <&vic>;
		interrupts = <31>; /* Cascaded to vic */
	};

  b) two cells
  ------------
  The #interrupt-cells property is set to 2 and the first cell defines the
  index of the interrupt within the controller, while the second cell is used
  to specify any of the following flags:
    - bits[3:0] trigger type and level flags
        1 = low-to-high edge triggered
        2 = high-to-low edge triggered
        4 = active high level-sensitive
        8 = active low level-sensitive

  Example:

	i2c@7000c000 {
		gpioext: gpio-adnp@41 {
			compatible = "ad,gpio-adnp";
			reg = <0x41>;

			interrupt-parent = <&gpio>;
			interrupts = <160 1>;

			gpio-controller;
			#gpio-cells = <1>;

			interrupt-controller;
			#interrupt-cells = <2>;

			nr-gpios = <64>;
		};

		sx8634@2b {
			compatible = "smtc,sx8634";
			reg = <0x2b>;

			interrupt-parent = <&gpioext>;
			interrupts = <3 0x8>;

			#address-cells = <1>;
			#size-cells = <0>;

			threshold = <0x40>;
			sensitivity = <7>;
		};
	};


Example of special form (supported by U-Boot):

	acpi_gpe: general-purpose-events {
		reg = <IOMAP_ACPI_BASE IOMAP_ACPI_SIZE>;
		compatible = "intel,acpi-gpe";
		interrupt-controller;
		#interrupt-cells = <2>;
	};

	tpm@50 {
		reg = <0x50>;
		compatible = "google,cr50";
		u-boot,i2c-offset-len = <0>;
		ready-gpio = <&gpio_n 28 GPIO_ACTIVE_LOW>;
		interrupts-extended = <&acpi_gpe 0x3c 0>;
	};