| /* SPDX-License-Identifier: GPL-2.0+ */ | |
| /* | |
| * (C) Copyright 2000-2004 | |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
| */ | |
| /* | |
| * The purpose of this code is to signal the operational status of a | |
| * target which usually boots over the network; while running in | |
| * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply | |
| * message has been received, the LED is turned off. The Linux | |
| * kernel, once it is running, will start blinking the LED again, | |
| * with another frequency. | |
| */ | |
| #ifndef _STATUS_LED_H_ | |
| #define _STATUS_LED_H_ | |
| #ifdef CONFIG_LED_STATUS | |
| #define LED_STATUS_PERIOD (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ) | |
| #ifdef CONFIG_LED_STATUS1 | |
| #define LED_STATUS_PERIOD1 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ1) | |
| #endif /* CONFIG_LED_STATUS1 */ | |
| #ifdef CONFIG_LED_STATUS2 | |
| #define LED_STATUS_PERIOD2 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ2) | |
| #endif /* CONFIG_LED_STATUS2 */ | |
| #ifdef CONFIG_LED_STATUS3 | |
| #define LED_STATUS_PERIOD3 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ3) | |
| #endif /* CONFIG_LED_STATUS3 */ | |
| #ifdef CONFIG_LED_STATUS4 | |
| #define LED_STATUS_PERIOD4 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ4) | |
| #endif /* CONFIG_LED_STATUS4 */ | |
| #ifdef CONFIG_LED_STATUS5 | |
| #define LED_STATUS_PERIOD5 (CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ5) | |
| #endif /* CONFIG_LED_STATUS5 */ | |
| void status_led_init(void); | |
| void status_led_tick(unsigned long timestamp); | |
| void status_led_set(int led, int state); | |
| /***** MVS v1 **********************************************************/ | |
| #if (defined(CONFIG_MVS) && CONFIG_MVS < 2) | |
| # define STATUS_LED_PAR im_ioport.iop_pdpar | |
| # define STATUS_LED_DIR im_ioport.iop_pddir | |
| # undef STATUS_LED_ODR | |
| # define STATUS_LED_DAT im_ioport.iop_pddat | |
| # define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ | |
| /***** Someone else defines these *************************************/ | |
| #elif defined(STATUS_LED_PAR) | |
| /* | |
| * ADVICE: Define in your board configuration file rather than | |
| * filling this file up with lots of custom board stuff. | |
| */ | |
| #elif defined(CONFIG_LED_STATUS_BOARD_SPECIFIC) | |
| /* led_id_t is unsigned long mask */ | |
| typedef unsigned long led_id_t; | |
| extern void __led_toggle (led_id_t mask); | |
| extern void __led_init (led_id_t mask, int state); | |
| extern void __led_set (led_id_t mask, int state); | |
| void __led_blink(led_id_t mask, int freq); | |
| #else | |
| # error Status LED configuration missing | |
| #endif | |
| /************************************************************************/ | |
| #ifndef CONFIG_LED_STATUS_BOARD_SPECIFIC | |
| # include <asm/status_led.h> | |
| #endif | |
| #endif /* CONFIG_LED_STATUS */ | |
| /* | |
| * Coloured LEDs API | |
| */ | |
| #ifndef __ASSEMBLY__ | |
| void coloured_LED_init(void); | |
| void red_led_on(void); | |
| void red_led_off(void); | |
| void green_led_on(void); | |
| void green_led_off(void); | |
| void yellow_led_on(void); | |
| void yellow_led_off(void); | |
| void blue_led_on(void); | |
| void blue_led_off(void); | |
| #else | |
| .extern LED_init | |
| .extern red_led_on | |
| .extern red_led_off | |
| .extern yellow_led_on | |
| .extern yellow_led_off | |
| .extern green_led_on | |
| .extern green_led_off | |
| .extern blue_led_on | |
| .extern blue_led_off | |
| #endif | |
| #endif /* _STATUS_LED_H_ */ |