| /* | |
| * (C) Copyright 2003 | |
| * Denis Peter d.peter@mpl.ch | |
| * | |
| * See file CREDITS for list of people who contributed to this | |
| * project. | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License as | |
| * published by the Free Software Foundation; either version 2 of | |
| * the License, or (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, | |
| */ | |
| /* | |
| * File: PATI.h | |
| */ | |
| #ifndef __CONFIG_H | |
| #define __CONFIG_H | |
| /* | |
| * High Level Configuration Options | |
| */ | |
| #define CONFIG_MPC555 1 /* This is an MPC555 CPU */ | |
| #define CONFIG_PATI 1 /* ...On a PATI board */ | |
| #define CONFIG_SYS_TEXT_BASE 0xFFF00000 | |
| /* Serial Console Configuration */ | |
| #define CONFIG_5xx_CONS_SCI1 | |
| #undef CONFIG_5xx_CONS_SCI2 | |
| #define CONFIG_BAUDRATE 9600 | |
| /* | |
| * BOOTP options | |
| */ | |
| #define CONFIG_BOOTP_BOOTFILESIZE | |
| #define CONFIG_BOOTP_BOOTPATH | |
| #define CONFIG_BOOTP_GATEWAY | |
| #define CONFIG_BOOTP_HOSTNAME | |
| /* | |
| * Command line configuration. | |
| */ | |
| #define CONFIG_CMD_MEMORY | |
| #define CONFIG_CMD_LOADB | |
| #define CONFIG_CMD_REGINFO | |
| #define CONFIG_CMD_FLASH | |
| #define CONFIG_CMD_LOADS | |
| #define CONFIG_CMD_SAVEENV | |
| #define CONFIG_CMD_REGINFO | |
| #define CONFIG_CMD_BDI | |
| #define CONFIG_CMD_CONSOLE | |
| #define CONFIG_CMD_RUN | |
| #define CONFIG_CMD_BSP | |
| #define CONFIG_CMD_IMI | |
| #define CONFIG_CMD_EEPROM | |
| #define CONFIG_CMD_IRQ | |
| #define CONFIG_CMD_MISC | |
| #if 0 | |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ | |
| #else | |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ | |
| #endif | |
| #define CONFIG_BOOTCOMMAND "" /* autoboot command */ | |
| #define CONFIG_BOOTARGS "" /* */ | |
| #define CONFIG_WATCHDOG /* turn on platform specific watchdog */ | |
| /*#define CONFIG_STATUS_LED 1 */ /* Enable status led */ | |
| #define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */ | |
| /* | |
| * Miscellaneous configurable options | |
| */ | |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */ | |
| #define CONFIG_PREBOOT | |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ | |
| #define CONFIG_SYS_PROMPT "pati=> " /* Monitor Command Prompt */ | |
| #if defined(CONFIG_CMD_KGDB) | |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ | |
| #else | |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ | |
| #endif | |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ | |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ | |
| #define CONFIG_SYS_MEMTEST_START 0x00010000 /* memtest works on */ | |
| #define CONFIG_SYS_MEMTEST_END 0x00A00000 /* 10 MB in SRAM */ | |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ | |
| #define CONFIG_SYS_HZ 1000 /* Decrementer freq: 1 ms ticks */ | |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } | |
| /*********************************************************************** | |
| * Last Stage Init | |
| ***********************************************************************/ | |
| #define CONFIG_LAST_STAGE_INIT | |
| /* | |
| * Low Level Configuration Settings | |
| */ | |
| /* | |
| * Internal Memory Mapped (This is not the IMMR content) | |
| */ | |
| #define CONFIG_SYS_IMMR 0x01C00000 /* Physical start adress of internal memory map */ | |
| /* | |
| * Definitions for initial stack pointer and data area | |
| */ | |
| #define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */ | |
| #define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */ | |
| #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */ | |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_IMMR + 0x03fa000) /* Physical start adress of inital stack */ | |
| /* | |
| * Start addresses for the final memory configuration | |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 | |
| */ | |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */ | |
| #define CONFIG_SYS_FLASH_BASE 0xffC00000 /* External flash */ | |
| #define PCI_BASE 0x03000000 /* PCI Base (CS2) */ | |
| #define PCI_CONFIG_BASE 0x04000000 /* PCI & PLD (CS3) */ | |
| #define PLD_CONFIG_BASE 0x04001000 /* PLD (CS3) */ | |
| #define CONFIG_SYS_MONITOR_BASE 0xFFF00000 | |
| /* CONFIG_SYS_FLASH_BASE */ /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */ | |
| /* This adress is given to the linker with -Ttext to */ | |
| /* locate the text section at this adress. */ | |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 192 kB for Monitor */ | |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ | |
| #define CONFIG_SYS_RESET_ADDRESS (PLD_CONFIG_BASE + 0x10) /* Adress which causes reset */ | |
| /* | |
| * For booting Linux, the board info and command line data | |
| * have to be in the first 8 MB of memory, since this is | |
| * the maximum mapped by the Linux kernel during initialization. | |
| */ | |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ | |
| /*----------------------------------------------------------------------- | |
| * FLASH organization | |
| *----------------------------------------------------------------------- | |
| * | |
| */ | |
| #define CONFIG_SYS_FLASH_PROTECTION | |
| #define CONFIG_SYS_FLASH_EMPTY_INFO | |
| #define CONFIG_SYS_FLASH_CFI | |
| #define CONFIG_FLASH_CFI_DRIVER | |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 | |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 | |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 | |
| #define CONFIG_ENV_IS_IN_EEPROM | |
| #ifdef CONFIG_ENV_IS_IN_EEPROM | |
| #define CONFIG_ENV_OFFSET 0 | |
| #define CONFIG_ENV_SIZE 2048 | |
| #endif | |
| #undef CONFIG_ENV_IS_IN_FLASH | |
| #ifdef CONFIG_ENV_IS_IN_FLASH | |
| #define CONFIG_ENV_SIZE 0x00002000 /* Set whole sector as env */ | |
| #define CONFIG_ENV_OFFSET ((0 - CONFIG_SYS_FLASH_BASE) - CONFIG_ENV_SIZE) /* Environment starts at this adress */ | |
| #endif | |
| #define CONFIG_SPI 1 | |
| #define CONFIG_SYS_SPI_CS_USED 0x09 /* CS0 and CS3 are used */ | |
| #define CONFIG_SYS_SPI_CS_BASE 0x08 /* CS3 is active low */ | |
| #define CONFIG_SYS_SPI_CS_ACT 0x00 /* CS3 is active low */ | |
| /*----------------------------------------------------------------------- | |
| * SYPCR - System Protection Control | |
| * SYPCR can only be written once after reset! | |
| *----------------------------------------------------------------------- | |
| * SW Watchdog freeze | |
| */ | |
| #undef CONFIG_WATCHDOG | |
| #if defined(CONFIG_WATCHDOG) | |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ | |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) | |
| #else | |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ | |
| SYPCR_SWP) | |
| #endif /* CONFIG_WATCHDOG */ | |
| /*----------------------------------------------------------------------- | |
| * TBSCR - Time Base Status and Control | |
| *----------------------------------------------------------------------- | |
| * Clear Reference Interrupt Status, Timebase freezing enabled | |
| */ | |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) | |
| /*----------------------------------------------------------------------- | |
| * PISCR - Periodic Interrupt Status and Control | |
| *----------------------------------------------------------------------- | |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled | |
| */ | |
| #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) | |
| /*----------------------------------------------------------------------- | |
| * SCCR - System Clock and reset Control Register | |
| *----------------------------------------------------------------------- | |
| * Set clock output, timebase and RTC source and divider, | |
| * power management and some other internal clocks | |
| */ | |
| #define SCCR_MASK SCCR_EBDF00 | |
| #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ | |
| SCCR_COM01 | SCCR_DFNL000 | SCCR_DFNH000) | |
| /*----------------------------------------------------------------------- | |
| * SIUMCR - SIU Module Configuration | |
| *----------------------------------------------------------------------- | |
| * Data show cycle | |
| */ | |
| #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_EARB | SIUMCR_GPC01 | SIUMCR_MLRC11) /* Disable data show cycle */ | |
| /*----------------------------------------------------------------------- | |
| * PLPRCR - PLL, Low-Power, and Reset Control Register | |
| *----------------------------------------------------------------------- | |
| * Set all bits to 40 Mhz | |
| * | |
| */ | |
| #define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */ | |
| #define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0) | |
| /*----------------------------------------------------------------------- | |
| * UMCR - UIMB Module Configuration Register | |
| *----------------------------------------------------------------------- | |
| * | |
| */ | |
| #define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */ | |
| /*----------------------------------------------------------------------- | |
| * ICTRL - I-Bus Support Control Register | |
| */ | |
| #define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */ | |
| /*----------------------------------------------------------------------- | |
| * USIU - Memory Controller Register | |
| *----------------------------------------------------------------------- | |
| */ | |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16 | BR_SETA) | |
| #define CONFIG_SYS_OR0_PRELIM (0xffc00000) /* SCY is not used if external TA is set */ | |
| /* SDRAM */ | |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA) | |
| #define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FF) /* SCY is not used if external TA is set */ | |
| /* PCI */ | |
| #define CONFIG_SYS_BR2_PRELIM (PCI_BASE | BR_V | BR_PS_32 | BR_SETA) | |
| #define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF) | |
| /* config registers: */ | |
| #define CONFIG_SYS_BR3_PRELIM (PCI_CONFIG_BASE | BR_V | BR_BI | BR_PS_32 | BR_SETA) | |
| #define CONFIG_SYS_OR3_PRELIM (0xffff0000) | |
| #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */ | |
| /*----------------------------------------------------------------------- | |
| * DER - Timer Decrementer | |
| *----------------------------------------------------------------------- | |
| * Initialise to zero | |
| */ | |
| #define CONFIG_SYS_DER 0x00000000 | |
| #define VERSION_TAG "released" | |
| #define CONFIG_ISO_STRING "MEV-10084-001" | |
| #define CONFIG_IDENT_STRING "\n(c) 2003 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG | |
| #endif /* __CONFIG_H */ |