| /* | |
| * RFC3927 ZeroConf IPv4 Link-Local addressing | |
| * (see <http://www.zeroconf.org/>) | |
| * | |
| * Copied from BusyBox - networking/zcip.c | |
| * | |
| * Copyright (C) 2003 by Arthur van Hoff (avh@strangeberry.com) | |
| * Copyright (C) 2004 by David Brownell | |
| * Copyright (C) 2010 by Joe Hershberger | |
| * | |
| * Licensed under the GPL v2 or later | |
| */ | |
| #include <common.h> | |
| #include <net.h> | |
| #include "arp.h" | |
| #include "net_rand.h" | |
| /* We don't need more than 32 bits of the counter */ | |
| #define MONOTONIC_MS() ((unsigned)get_timer(0) * (1000 / CONFIG_SYS_HZ)) | |
| enum { | |
| /* 169.254.0.0 */ | |
| LINKLOCAL_ADDR = 0xa9fe0000, | |
| IN_CLASSB_NET = 0xffff0000, | |
| IN_CLASSB_HOST = 0x0000ffff, | |
| /* protocol timeout parameters, specified in seconds */ | |
| PROBE_WAIT = 1, | |
| PROBE_MIN = 1, | |
| PROBE_MAX = 2, | |
| PROBE_NUM = 3, | |
| MAX_CONFLICTS = 10, | |
| RATE_LIMIT_INTERVAL = 60, | |
| ANNOUNCE_WAIT = 2, | |
| ANNOUNCE_NUM = 2, | |
| ANNOUNCE_INTERVAL = 2, | |
| DEFEND_INTERVAL = 10 | |
| }; | |
| /* States during the configuration process. */ | |
| static enum ll_state_t { | |
| PROBE = 0, | |
| RATE_LIMIT_PROBE, | |
| ANNOUNCE, | |
| MONITOR, | |
| DEFEND, | |
| DISABLED | |
| } state = DISABLED; | |
| static struct in_addr ip; | |
| static int timeout_ms = -1; | |
| static unsigned deadline_ms; | |
| static unsigned conflicts; | |
| static unsigned nprobes; | |
| static unsigned nclaims; | |
| static int ready; | |
| static unsigned int seed; | |
| static void link_local_timeout(void); | |
| /** | |
| * Pick a random link local IP address on 169.254/16, except that | |
| * the first and last 256 addresses are reserved. | |
| */ | |
| static struct in_addr pick(void) | |
| { | |
| unsigned tmp; | |
| struct in_addr ip; | |
| do { | |
| tmp = rand_r(&seed) & IN_CLASSB_HOST; | |
| } while (tmp > (IN_CLASSB_HOST - 0x0200)); | |
| ip.s_addr = htonl((LINKLOCAL_ADDR + 0x0100) + tmp); | |
| return ip; | |
| } | |
| /** | |
| * Return milliseconds of random delay, up to "secs" seconds. | |
| */ | |
| static inline unsigned random_delay_ms(unsigned secs) | |
| { | |
| return rand_r(&seed) % (secs * 1000); | |
| } | |
| static void configure_wait(void) | |
| { | |
| if (timeout_ms == -1) | |
| return; | |
| /* poll, being ready to adjust current timeout */ | |
| if (!timeout_ms) | |
| timeout_ms = random_delay_ms(PROBE_WAIT); | |
| /* set deadline_ms to the point in time when we timeout */ | |
| deadline_ms = MONOTONIC_MS() + timeout_ms; | |
| debug_cond(DEBUG_DEV_PKT, "...wait %d %s nprobes=%u, nclaims=%u\n", | |
| timeout_ms, eth_get_name(), nprobes, nclaims); | |
| net_set_timeout_handler(timeout_ms, link_local_timeout); | |
| } | |
| void link_local_start(void) | |
| { | |
| ip = env_get_ip("llipaddr"); | |
| if (ip.s_addr != 0 && | |
| (ntohl(ip.s_addr) & IN_CLASSB_NET) != LINKLOCAL_ADDR) { | |
| puts("invalid link address"); | |
| net_set_state(NETLOOP_FAIL); | |
| return; | |
| } | |
| net_netmask.s_addr = htonl(IN_CLASSB_NET); | |
| seed = seed_mac(); | |
| if (ip.s_addr == 0) | |
| ip = pick(); | |
| state = PROBE; | |
| timeout_ms = 0; | |
| conflicts = 0; | |
| nprobes = 0; | |
| nclaims = 0; | |
| ready = 0; | |
| configure_wait(); | |
| } | |
| static void link_local_timeout(void) | |
| { | |
| switch (state) { | |
| case PROBE: | |
| /* timeouts in the PROBE state mean no conflicting ARP packets | |
| have been received, so we can progress through the states */ | |
| if (nprobes < PROBE_NUM) { | |
| struct in_addr zero_ip = {.s_addr = 0}; | |
| nprobes++; | |
| debug_cond(DEBUG_LL_STATE, "probe/%u %s@%pI4\n", | |
| nprobes, eth_get_name(), &ip); | |
| arp_raw_request(zero_ip, net_null_ethaddr, ip); | |
| timeout_ms = PROBE_MIN * 1000; | |
| timeout_ms += random_delay_ms(PROBE_MAX - PROBE_MIN); | |
| } else { | |
| /* Switch to announce state */ | |
| state = ANNOUNCE; | |
| nclaims = 0; | |
| debug_cond(DEBUG_LL_STATE, "announce/%u %s@%pI4\n", | |
| nclaims, eth_get_name(), &ip); | |
| arp_raw_request(ip, net_ethaddr, ip); | |
| timeout_ms = ANNOUNCE_INTERVAL * 1000; | |
| } | |
| break; | |
| case RATE_LIMIT_PROBE: | |
| /* timeouts in the RATE_LIMIT_PROBE state mean no conflicting | |
| ARP packets have been received, so we can move immediately | |
| to the announce state */ | |
| state = ANNOUNCE; | |
| nclaims = 0; | |
| debug_cond(DEBUG_LL_STATE, "announce/%u %s@%pI4\n", | |
| nclaims, eth_get_name(), &ip); | |
| arp_raw_request(ip, net_ethaddr, ip); | |
| timeout_ms = ANNOUNCE_INTERVAL * 1000; | |
| break; | |
| case ANNOUNCE: | |
| /* timeouts in the ANNOUNCE state mean no conflicting ARP | |
| packets have been received, so we can progress through | |
| the states */ | |
| if (nclaims < ANNOUNCE_NUM) { | |
| nclaims++; | |
| debug_cond(DEBUG_LL_STATE, "announce/%u %s@%pI4\n", | |
| nclaims, eth_get_name(), &ip); | |
| arp_raw_request(ip, net_ethaddr, ip); | |
| timeout_ms = ANNOUNCE_INTERVAL * 1000; | |
| } else { | |
| /* Switch to monitor state */ | |
| state = MONITOR; | |
| printf("Successfully assigned %pI4\n", &ip); | |
| net_copy_ip(&net_ip, &ip); | |
| ready = 1; | |
| conflicts = 0; | |
| timeout_ms = -1; | |
| /* Never timeout in the monitor state */ | |
| net_set_timeout_handler(0, NULL); | |
| /* NOTE: all other exit paths should deconfig ... */ | |
| net_set_state(NETLOOP_SUCCESS); | |
| return; | |
| } | |
| break; | |
| case DEFEND: | |
| /* We won! No ARP replies, so just go back to monitor */ | |
| state = MONITOR; | |
| timeout_ms = -1; | |
| conflicts = 0; | |
| break; | |
| default: | |
| /* Invalid, should never happen. Restart the whole protocol */ | |
| state = PROBE; | |
| ip = pick(); | |
| timeout_ms = 0; | |
| nprobes = 0; | |
| nclaims = 0; | |
| break; | |
| } | |
| configure_wait(); | |
| } | |
| void link_local_receive_arp(struct arp_hdr *arp, int len) | |
| { | |
| int source_ip_conflict; | |
| int target_ip_conflict; | |
| struct in_addr null_ip = {.s_addr = 0}; | |
| if (state == DISABLED) | |
| return; | |
| /* We need to adjust the timeout in case we didn't receive a | |
| conflicting packet. */ | |
| if (timeout_ms > 0) { | |
| unsigned diff = deadline_ms - MONOTONIC_MS(); | |
| if ((int)(diff) < 0) { | |
| /* Current time is greater than the expected timeout | |
| time. This should never happen */ | |
| debug_cond(DEBUG_LL_STATE, | |
| "missed an expected timeout\n"); | |
| timeout_ms = 0; | |
| } else { | |
| debug_cond(DEBUG_INT_STATE, "adjusting timeout\n"); | |
| timeout_ms = diff | 1; /* never 0 */ | |
| } | |
| } | |
| #if 0 | |
| /* XXX Don't bother with ethernet link just yet */ | |
| if ((fds[0].revents & POLLIN) == 0) { | |
| if (fds[0].revents & POLLERR) { | |
| /* | |
| * FIXME: links routinely go down; | |
| */ | |
| bb_error_msg("iface %s is down", eth_get_name()); | |
| if (ready) | |
| run(argv, "deconfig", &ip); | |
| return EXIT_FAILURE; | |
| } | |
| continue; | |
| } | |
| #endif | |
| debug_cond(DEBUG_INT_STATE, "%s recv arp type=%d, op=%d,\n", | |
| eth_get_name(), ntohs(arp->ar_pro), | |
| ntohs(arp->ar_op)); | |
| debug_cond(DEBUG_INT_STATE, "\tsource=%pM %pI4\n", | |
| &arp->ar_sha, | |
| &arp->ar_spa); | |
| debug_cond(DEBUG_INT_STATE, "\ttarget=%pM %pI4\n", | |
| &arp->ar_tha, | |
| &arp->ar_tpa); | |
| if (arp->ar_op != htons(ARPOP_REQUEST) && | |
| arp->ar_op != htons(ARPOP_REPLY)) { | |
| configure_wait(); | |
| return; | |
| } | |
| source_ip_conflict = 0; | |
| target_ip_conflict = 0; | |
| if (memcmp(&arp->ar_spa, &ip, ARP_PLEN) == 0 && | |
| memcmp(&arp->ar_sha, net_ethaddr, ARP_HLEN) != 0) | |
| source_ip_conflict = 1; | |
| /* | |
| * According to RFC 3927, section 2.2.1: | |
| * Check if packet is an ARP probe by checking for a null source IP | |
| * then check that target IP is equal to ours and source hw addr | |
| * is not equal to ours. This condition should cause a conflict only | |
| * during probe. | |
| */ | |
| if (arp->ar_op == htons(ARPOP_REQUEST) && | |
| memcmp(&arp->ar_spa, &null_ip, ARP_PLEN) == 0 && | |
| memcmp(&arp->ar_tpa, &ip, ARP_PLEN) == 0 && | |
| memcmp(&arp->ar_sha, net_ethaddr, ARP_HLEN) != 0) { | |
| target_ip_conflict = 1; | |
| } | |
| debug_cond(DEBUG_NET_PKT, | |
| "state = %d, source ip conflict = %d, target ip conflict = " | |
| "%d\n", state, source_ip_conflict, target_ip_conflict); | |
| switch (state) { | |
| case PROBE: | |
| case ANNOUNCE: | |
| /* When probing or announcing, check for source IP conflicts | |
| and other hosts doing ARP probes (target IP conflicts). */ | |
| if (source_ip_conflict || target_ip_conflict) { | |
| conflicts++; | |
| state = PROBE; | |
| if (conflicts >= MAX_CONFLICTS) { | |
| debug("%s ratelimit\n", eth_get_name()); | |
| timeout_ms = RATE_LIMIT_INTERVAL * 1000; | |
| state = RATE_LIMIT_PROBE; | |
| } | |
| /* restart the whole protocol */ | |
| ip = pick(); | |
| timeout_ms = 0; | |
| nprobes = 0; | |
| nclaims = 0; | |
| } | |
| break; | |
| case MONITOR: | |
| /* If a conflict, we try to defend with a single ARP probe */ | |
| if (source_ip_conflict) { | |
| debug("monitor conflict -- defending\n"); | |
| state = DEFEND; | |
| timeout_ms = DEFEND_INTERVAL * 1000; | |
| arp_raw_request(ip, net_ethaddr, ip); | |
| } | |
| break; | |
| case DEFEND: | |
| /* Well, we tried. Start over (on conflict) */ | |
| if (source_ip_conflict) { | |
| state = PROBE; | |
| debug("defend conflict -- starting over\n"); | |
| ready = 0; | |
| net_ip.s_addr = 0; | |
| /* restart the whole protocol */ | |
| ip = pick(); | |
| timeout_ms = 0; | |
| nprobes = 0; | |
| nclaims = 0; | |
| } | |
| break; | |
| default: | |
| /* Invalid, should never happen. Restart the whole protocol */ | |
| debug("invalid state -- starting over\n"); | |
| state = PROBE; | |
| ip = pick(); | |
| timeout_ms = 0; | |
| nprobes = 0; | |
| nclaims = 0; | |
| break; | |
| } | |
| configure_wait(); | |
| } |