| /* | |
| * (C) Copyright 2002 Wolfgang Grandegger, wg@denx.de. | |
| * | |
| * This driver for AMD PCnet network controllers is derived from the | |
| * Linux driver pcnet32.c written 1996-1999 by Thomas Bogendoerfer. | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| #include <common.h> | |
| #include <malloc.h> | |
| #include <net.h> | |
| #include <netdev.h> | |
| #include <asm/io.h> | |
| #include <pci.h> | |
| #define PCNET_DEBUG_LEVEL 0 /* 0=off, 1=init, 2=rx/tx */ | |
| #define PCNET_DEBUG1(fmt,args...) \ | |
| debug_cond(PCNET_DEBUG_LEVEL > 0, fmt ,##args) | |
| #define PCNET_DEBUG2(fmt,args...) \ | |
| debug_cond(PCNET_DEBUG_LEVEL > 1, fmt ,##args) | |
| #if !defined(CONF_PCNET_79C973) && defined(CONF_PCNET_79C975) | |
| #error "Macro for PCnet chip version is not defined!" | |
| #endif | |
| /* | |
| * Set the number of Tx and Rx buffers, using Log_2(# buffers). | |
| * Reasonable default values are 4 Tx buffers, and 16 Rx buffers. | |
| * That translates to 2 (4 == 2^^2) and 4 (16 == 2^^4). | |
| */ | |
| #define PCNET_LOG_TX_BUFFERS 0 | |
| #define PCNET_LOG_RX_BUFFERS 2 | |
| #define TX_RING_SIZE (1 << (PCNET_LOG_TX_BUFFERS)) | |
| #define TX_RING_LEN_BITS ((PCNET_LOG_TX_BUFFERS) << 12) | |
| #define RX_RING_SIZE (1 << (PCNET_LOG_RX_BUFFERS)) | |
| #define RX_RING_LEN_BITS ((PCNET_LOG_RX_BUFFERS) << 4) | |
| #define PKT_BUF_SZ 1544 | |
| /* The PCNET Rx and Tx ring descriptors. */ | |
| struct pcnet_rx_head { | |
| u32 base; | |
| s16 buf_length; | |
| s16 status; | |
| u32 msg_length; | |
| u32 reserved; | |
| }; | |
| struct pcnet_tx_head { | |
| u32 base; | |
| s16 length; | |
| s16 status; | |
| u32 misc; | |
| u32 reserved; | |
| }; | |
| /* The PCNET 32-Bit initialization block, described in databook. */ | |
| struct pcnet_init_block { | |
| u16 mode; | |
| u16 tlen_rlen; | |
| u8 phys_addr[6]; | |
| u16 reserved; | |
| u32 filter[2]; | |
| /* Receive and transmit ring base, along with extra bits. */ | |
| u32 rx_ring; | |
| u32 tx_ring; | |
| u32 reserved2; | |
| }; | |
| struct pcnet_uncached_priv { | |
| struct pcnet_rx_head rx_ring[RX_RING_SIZE]; | |
| struct pcnet_tx_head tx_ring[TX_RING_SIZE]; | |
| struct pcnet_init_block init_block; | |
| }; | |
| typedef struct pcnet_priv { | |
| struct pcnet_uncached_priv *uc; | |
| /* Receive Buffer space */ | |
| unsigned char (*rx_buf)[RX_RING_SIZE][PKT_BUF_SZ + 4]; | |
| int cur_rx; | |
| int cur_tx; | |
| } pcnet_priv_t; | |
| static pcnet_priv_t *lp; | |
| /* Offsets from base I/O address for WIO mode */ | |
| #define PCNET_RDP 0x10 | |
| #define PCNET_RAP 0x12 | |
| #define PCNET_RESET 0x14 | |
| #define PCNET_BDP 0x16 | |
| static u16 pcnet_read_csr(struct eth_device *dev, int index) | |
| { | |
| outw(index, dev->iobase + PCNET_RAP); | |
| return inw(dev->iobase + PCNET_RDP); | |
| } | |
| static void pcnet_write_csr(struct eth_device *dev, int index, u16 val) | |
| { | |
| outw(index, dev->iobase + PCNET_RAP); | |
| outw(val, dev->iobase + PCNET_RDP); | |
| } | |
| static u16 pcnet_read_bcr(struct eth_device *dev, int index) | |
| { | |
| outw(index, dev->iobase + PCNET_RAP); | |
| return inw(dev->iobase + PCNET_BDP); | |
| } | |
| static void pcnet_write_bcr(struct eth_device *dev, int index, u16 val) | |
| { | |
| outw(index, dev->iobase + PCNET_RAP); | |
| outw(val, dev->iobase + PCNET_BDP); | |
| } | |
| static void pcnet_reset(struct eth_device *dev) | |
| { | |
| inw(dev->iobase + PCNET_RESET); | |
| } | |
| static int pcnet_check(struct eth_device *dev) | |
| { | |
| outw(88, dev->iobase + PCNET_RAP); | |
| return inw(dev->iobase + PCNET_RAP) == 88; | |
| } | |
| static int pcnet_init (struct eth_device *dev, bd_t * bis); | |
| static int pcnet_send(struct eth_device *dev, void *packet, int length); | |
| static int pcnet_recv (struct eth_device *dev); | |
| static void pcnet_halt (struct eth_device *dev); | |
| static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_num); | |
| #define PCI_TO_MEM(d, a) pci_virt_to_mem((pci_dev_t)d->priv, (a)) | |
| #define PCI_TO_MEM_LE(d,a) (u32)(cpu_to_le32(PCI_TO_MEM(d,a))) | |
| static struct pci_device_id supported[] = { | |
| {PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE}, | |
| {} | |
| }; | |
| int pcnet_initialize(bd_t *bis) | |
| { | |
| pci_dev_t devbusfn; | |
| struct eth_device *dev; | |
| u16 command, status; | |
| int dev_nr = 0; | |
| PCNET_DEBUG1("\npcnet_initialize...\n"); | |
| for (dev_nr = 0;; dev_nr++) { | |
| /* | |
| * Find the PCnet PCI device(s). | |
| */ | |
| devbusfn = pci_find_devices(supported, dev_nr); | |
| if (devbusfn < 0) | |
| break; | |
| /* | |
| * Allocate and pre-fill the device structure. | |
| */ | |
| dev = (struct eth_device *)malloc(sizeof(*dev)); | |
| if (!dev) { | |
| printf("pcnet: Can not allocate memory\n"); | |
| break; | |
| } | |
| memset(dev, 0, sizeof(*dev)); | |
| dev->priv = (void *)devbusfn; | |
| sprintf(dev->name, "pcnet#%d", dev_nr); | |
| /* | |
| * Setup the PCI device. | |
| */ | |
| pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, | |
| (unsigned int *)&dev->iobase); | |
| dev->iobase = pci_io_to_phys(devbusfn, dev->iobase); | |
| dev->iobase &= ~0xf; | |
| PCNET_DEBUG1("%s: devbusfn=0x%x iobase=0x%x: ", | |
| dev->name, devbusfn, dev->iobase); | |
| command = PCI_COMMAND_IO | PCI_COMMAND_MASTER; | |
| pci_write_config_word(devbusfn, PCI_COMMAND, command); | |
| pci_read_config_word(devbusfn, PCI_COMMAND, &status); | |
| if ((status & command) != command) { | |
| printf("%s: Couldn't enable IO access or Bus Mastering\n", | |
| dev->name); | |
| free(dev); | |
| continue; | |
| } | |
| pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x40); | |
| /* | |
| * Probe the PCnet chip. | |
| */ | |
| if (pcnet_probe(dev, bis, dev_nr) < 0) { | |
| free(dev); | |
| continue; | |
| } | |
| /* | |
| * Setup device structure and register the driver. | |
| */ | |
| dev->init = pcnet_init; | |
| dev->halt = pcnet_halt; | |
| dev->send = pcnet_send; | |
| dev->recv = pcnet_recv; | |
| eth_register(dev); | |
| } | |
| udelay(10 * 1000); | |
| return dev_nr; | |
| } | |
| static int pcnet_probe(struct eth_device *dev, bd_t *bis, int dev_nr) | |
| { | |
| int chip_version; | |
| char *chipname; | |
| #ifdef PCNET_HAS_PROM | |
| int i; | |
| #endif | |
| /* Reset the PCnet controller */ | |
| pcnet_reset(dev); | |
| /* Check if register access is working */ | |
| if (pcnet_read_csr(dev, 0) != 4 || !pcnet_check(dev)) { | |
| printf("%s: CSR register access check failed\n", dev->name); | |
| return -1; | |
| } | |
| /* Identify the chip */ | |
| chip_version = | |
| pcnet_read_csr(dev, 88) | (pcnet_read_csr(dev, 89) << 16); | |
| if ((chip_version & 0xfff) != 0x003) | |
| return -1; | |
| chip_version = (chip_version >> 12) & 0xffff; | |
| switch (chip_version) { | |
| case 0x2621: | |
| chipname = "PCnet/PCI II 79C970A"; /* PCI */ | |
| break; | |
| #ifdef CONFIG_PCNET_79C973 | |
| case 0x2625: | |
| chipname = "PCnet/FAST III 79C973"; /* PCI */ | |
| break; | |
| #endif | |
| #ifdef CONFIG_PCNET_79C975 | |
| case 0x2627: | |
| chipname = "PCnet/FAST III 79C975"; /* PCI */ | |
| break; | |
| #endif | |
| default: | |
| printf("%s: PCnet version %#x not supported\n", | |
| dev->name, chip_version); | |
| return -1; | |
| } | |
| PCNET_DEBUG1("AMD %s\n", chipname); | |
| #ifdef PCNET_HAS_PROM | |
| /* | |
| * In most chips, after a chip reset, the ethernet address is read from | |
| * the station address PROM at the base address and programmed into the | |
| * "Physical Address Registers" CSR12-14. | |
| */ | |
| for (i = 0; i < 3; i++) { | |
| unsigned int val; | |
| val = pcnet_read_csr(dev, i + 12) & 0x0ffff; | |
| /* There may be endianness issues here. */ | |
| dev->enetaddr[2 * i] = val & 0x0ff; | |
| dev->enetaddr[2 * i + 1] = (val >> 8) & 0x0ff; | |
| } | |
| #endif /* PCNET_HAS_PROM */ | |
| return 0; | |
| } | |
| static int pcnet_init(struct eth_device *dev, bd_t *bis) | |
| { | |
| struct pcnet_uncached_priv *uc; | |
| int i, val; | |
| u32 addr; | |
| PCNET_DEBUG1("%s: pcnet_init...\n", dev->name); | |
| /* Switch pcnet to 32bit mode */ | |
| pcnet_write_bcr(dev, 20, 2); | |
| /* Set/reset autoselect bit */ | |
| val = pcnet_read_bcr(dev, 2) & ~2; | |
| val |= 2; | |
| pcnet_write_bcr(dev, 2, val); | |
| /* Enable auto negotiate, setup, disable fd */ | |
| val = pcnet_read_bcr(dev, 32) & ~0x98; | |
| val |= 0x20; | |
| pcnet_write_bcr(dev, 32, val); | |
| /* | |
| * Enable NOUFLO on supported controllers, with the transmit | |
| * start point set to the full packet. This will cause entire | |
| * packets to be buffered by the ethernet controller before | |
| * transmission, eliminating underflows which are common on | |
| * slower devices. Controllers which do not support NOUFLO will | |
| * simply be left with a larger transmit FIFO threshold. | |
| */ | |
| val = pcnet_read_bcr(dev, 18); | |
| val |= 1 << 11; | |
| pcnet_write_bcr(dev, 18, val); | |
| val = pcnet_read_csr(dev, 80); | |
| val |= 0x3 << 10; | |
| pcnet_write_csr(dev, 80, val); | |
| /* | |
| * We only maintain one structure because the drivers will never | |
| * be used concurrently. In 32bit mode the RX and TX ring entries | |
| * must be aligned on 16-byte boundaries. | |
| */ | |
| if (lp == NULL) { | |
| addr = (u32)malloc(sizeof(pcnet_priv_t) + 0x10); | |
| addr = (addr + 0xf) & ~0xf; | |
| lp = (pcnet_priv_t *)addr; | |
| addr = (u32)memalign(ARCH_DMA_MINALIGN, sizeof(*lp->uc)); | |
| flush_dcache_range(addr, addr + sizeof(*lp->uc)); | |
| addr = UNCACHED_SDRAM(addr); | |
| lp->uc = (struct pcnet_uncached_priv *)addr; | |
| addr = (u32)memalign(ARCH_DMA_MINALIGN, sizeof(*lp->rx_buf)); | |
| flush_dcache_range(addr, addr + sizeof(*lp->rx_buf)); | |
| lp->rx_buf = (void *)addr; | |
| } | |
| uc = lp->uc; | |
| uc->init_block.mode = cpu_to_le16(0x0000); | |
| uc->init_block.filter[0] = 0x00000000; | |
| uc->init_block.filter[1] = 0x00000000; | |
| /* | |
| * Initialize the Rx ring. | |
| */ | |
| lp->cur_rx = 0; | |
| for (i = 0; i < RX_RING_SIZE; i++) { | |
| uc->rx_ring[i].base = PCI_TO_MEM_LE(dev, (*lp->rx_buf)[i]); | |
| uc->rx_ring[i].buf_length = cpu_to_le16(-PKT_BUF_SZ); | |
| uc->rx_ring[i].status = cpu_to_le16(0x8000); | |
| PCNET_DEBUG1 | |
| ("Rx%d: base=0x%x buf_length=0x%hx status=0x%hx\n", i, | |
| uc->rx_ring[i].base, uc->rx_ring[i].buf_length, | |
| uc->rx_ring[i].status); | |
| } | |
| /* | |
| * Initialize the Tx ring. The Tx buffer address is filled in as | |
| * needed, but we do need to clear the upper ownership bit. | |
| */ | |
| lp->cur_tx = 0; | |
| for (i = 0; i < TX_RING_SIZE; i++) { | |
| uc->tx_ring[i].base = 0; | |
| uc->tx_ring[i].status = 0; | |
| } | |
| /* | |
| * Setup Init Block. | |
| */ | |
| PCNET_DEBUG1("Init block at 0x%p: MAC", &lp->uc->init_block); | |
| for (i = 0; i < 6; i++) { | |
| lp->uc->init_block.phys_addr[i] = dev->enetaddr[i]; | |
| PCNET_DEBUG1(" %02x", lp->uc->init_block.phys_addr[i]); | |
| } | |
| uc->init_block.tlen_rlen = cpu_to_le16(TX_RING_LEN_BITS | | |
| RX_RING_LEN_BITS); | |
| uc->init_block.rx_ring = PCI_TO_MEM_LE(dev, uc->rx_ring); | |
| uc->init_block.tx_ring = PCI_TO_MEM_LE(dev, uc->tx_ring); | |
| PCNET_DEBUG1("\ntlen_rlen=0x%x rx_ring=0x%x tx_ring=0x%x\n", | |
| uc->init_block.tlen_rlen, | |
| uc->init_block.rx_ring, uc->init_block.tx_ring); | |
| /* | |
| * Tell the controller where the Init Block is located. | |
| */ | |
| barrier(); | |
| addr = PCI_TO_MEM(dev, &lp->uc->init_block); | |
| pcnet_write_csr(dev, 1, addr & 0xffff); | |
| pcnet_write_csr(dev, 2, (addr >> 16) & 0xffff); | |
| pcnet_write_csr(dev, 4, 0x0915); | |
| pcnet_write_csr(dev, 0, 0x0001); /* start */ | |
| /* Wait for Init Done bit */ | |
| for (i = 10000; i > 0; i--) { | |
| if (pcnet_read_csr(dev, 0) & 0x0100) | |
| break; | |
| udelay(10); | |
| } | |
| if (i <= 0) { | |
| printf("%s: TIMEOUT: controller init failed\n", dev->name); | |
| pcnet_reset(dev); | |
| return -1; | |
| } | |
| /* | |
| * Finally start network controller operation. | |
| */ | |
| pcnet_write_csr(dev, 0, 0x0002); | |
| return 0; | |
| } | |
| static int pcnet_send(struct eth_device *dev, void *packet, int pkt_len) | |
| { | |
| int i, status; | |
| struct pcnet_tx_head *entry = &lp->uc->tx_ring[lp->cur_tx]; | |
| PCNET_DEBUG2("Tx%d: %d bytes from 0x%p ", lp->cur_tx, pkt_len, | |
| packet); | |
| flush_dcache_range((unsigned long)packet, | |
| (unsigned long)packet + pkt_len); | |
| /* Wait for completion by testing the OWN bit */ | |
| for (i = 1000; i > 0; i--) { | |
| status = readw(&entry->status); | |
| if ((status & 0x8000) == 0) | |
| break; | |
| udelay(100); | |
| PCNET_DEBUG2("."); | |
| } | |
| if (i <= 0) { | |
| printf("%s: TIMEOUT: Tx%d failed (status = 0x%x)\n", | |
| dev->name, lp->cur_tx, status); | |
| pkt_len = 0; | |
| goto failure; | |
| } | |
| /* | |
| * Setup Tx ring. Caution: the write order is important here, | |
| * set the status with the "ownership" bits last. | |
| */ | |
| writew(-pkt_len, &entry->length); | |
| writel(0, &entry->misc); | |
| writel(PCI_TO_MEM(dev, packet), &entry->base); | |
| writew(0x8300, &entry->status); | |
| /* Trigger an immediate send poll. */ | |
| pcnet_write_csr(dev, 0, 0x0008); | |
| failure: | |
| if (++lp->cur_tx >= TX_RING_SIZE) | |
| lp->cur_tx = 0; | |
| PCNET_DEBUG2("done\n"); | |
| return pkt_len; | |
| } | |
| static int pcnet_recv (struct eth_device *dev) | |
| { | |
| struct pcnet_rx_head *entry; | |
| unsigned char *buf; | |
| int pkt_len = 0; | |
| u16 status, err_status; | |
| while (1) { | |
| entry = &lp->uc->rx_ring[lp->cur_rx]; | |
| /* | |
| * If we own the next entry, it's a new packet. Send it up. | |
| */ | |
| status = readw(&entry->status); | |
| if ((status & 0x8000) != 0) | |
| break; | |
| err_status = status >> 8; | |
| if (err_status != 0x03) { /* There was an error. */ | |
| printf("%s: Rx%d", dev->name, lp->cur_rx); | |
| PCNET_DEBUG1(" (status=0x%x)", err_status); | |
| if (err_status & 0x20) | |
| printf(" Frame"); | |
| if (err_status & 0x10) | |
| printf(" Overflow"); | |
| if (err_status & 0x08) | |
| printf(" CRC"); | |
| if (err_status & 0x04) | |
| printf(" Fifo"); | |
| printf(" Error\n"); | |
| status &= 0x03ff; | |
| } else { | |
| pkt_len = (readl(&entry->msg_length) & 0xfff) - 4; | |
| if (pkt_len < 60) { | |
| printf("%s: Rx%d: invalid packet length %d\n", | |
| dev->name, lp->cur_rx, pkt_len); | |
| } else { | |
| buf = (*lp->rx_buf)[lp->cur_rx]; | |
| invalidate_dcache_range((unsigned long)buf, | |
| (unsigned long)buf + pkt_len); | |
| net_process_received_packet(buf, pkt_len); | |
| PCNET_DEBUG2("Rx%d: %d bytes from 0x%p\n", | |
| lp->cur_rx, pkt_len, buf); | |
| } | |
| } | |
| status |= 0x8000; | |
| writew(status, &entry->status); | |
| if (++lp->cur_rx >= RX_RING_SIZE) | |
| lp->cur_rx = 0; | |
| } | |
| return pkt_len; | |
| } | |
| static void pcnet_halt(struct eth_device *dev) | |
| { | |
| int i; | |
| PCNET_DEBUG1("%s: pcnet_halt...\n", dev->name); | |
| /* Reset the PCnet controller */ | |
| pcnet_reset(dev); | |
| /* Wait for Stop bit */ | |
| for (i = 1000; i > 0; i--) { | |
| if (pcnet_read_csr(dev, 0) & 0x4) | |
| break; | |
| udelay(10); | |
| } | |
| if (i <= 0) | |
| printf("%s: TIMEOUT: controller reset failed\n", dev->name); | |
| } |