| /* | |
| * (C) Copyright 2001 | |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. | |
| * | |
| * SPDX-License-Identifier: GPL-2.0+ | |
| */ | |
| /* | |
| * board/config.h - configuration options, board specific | |
| */ | |
| #ifndef __CONFIG_H | |
| #define __CONFIG_H | |
| /*********************************************************** | |
| * High Level Configuration Options | |
| * (easy to change) | |
| ***********************************************************/ | |
| #define CONFIG_405GP 1 /* This is a PPC405 CPU */ | |
| #define CONFIG_PIP405 1 /* ...on a PIP405 board */ | |
| #define CONFIG_SYS_TEXT_BASE 0xFFF80000 | |
| /*********************************************************** | |
| * Clock | |
| ***********************************************************/ | |
| #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ | |
| /* | |
| * BOOTP options | |
| */ | |
| #define CONFIG_BOOTP_BOOTFILESIZE | |
| #define CONFIG_BOOTP_BOOTPATH | |
| #define CONFIG_BOOTP_GATEWAY | |
| #define CONFIG_BOOTP_HOSTNAME | |
| /* | |
| * Command line configuration. | |
| */ | |
| #define CONFIG_CMD_IDE | |
| #define CONFIG_CMD_DHCP | |
| #define CONFIG_CMD_PCI | |
| #define CONFIG_CMD_CACHE | |
| #define CONFIG_CMD_IRQ | |
| #define CONFIG_CMD_EEPROM | |
| #define CONFIG_CMD_I2C | |
| #define CONFIG_CMD_REGINFO | |
| #define CONFIG_CMD_FDC | |
| #define CONFIG_CMD_SCSI | |
| #define CONFIG_CMD_FAT | |
| #define CONFIG_CMD_DATE | |
| #define CONFIG_CMD_USB | |
| #define CONFIG_CMD_MII | |
| #define CONFIG_CMD_SDRAM | |
| #define CONFIG_CMD_PING | |
| #define CONFIG_CMD_SAVES | |
| #define CONFIG_CMD_BSP | |
| #define CONFIG_SYS_HUSH_PARSER | |
| /************************************************************** | |
| * I2C Stuff: | |
| * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address | |
| * 0x53. | |
| * Caution: on the same bus is the SPD (Serial Presens Detect | |
| * EEPROM of the SDRAM | |
| * The Atmel EEPROM uses 16Bit addressing. | |
| ***************************************************************/ | |
| #define CONFIG_SYS_I2C | |
| #define CONFIG_SYS_I2C_PPC4XX | |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 | |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 50000 | |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F | |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 | |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 | |
| #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ | |
| #define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ | |
| #define CONFIG_ENV_SIZE 0x800 /* 2 kBytes may be used for env vars */ | |
| #undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW | |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel 24C128/256 has */ | |
| /* 64 byte page write mode using*/ | |
| /* last 6 bits of the address */ | |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ | |
| /*************************************************************** | |
| * Definitions for Serial Presence Detect EEPROM address | |
| * (to get SDRAM settings) | |
| ***************************************************************/ | |
| #define SPD_EEPROM_ADDRESS 0x50 | |
| #define CONFIG_BOARD_EARLY_INIT_F | |
| #define CONFIG_BOARD_EARLY_INIT_R | |
| /************************************************************** | |
| * Environment definitions | |
| **************************************************************/ | |
| #define CONFIG_BAUDRATE 9600 /* STD Baudrate */ | |
| #define CONFIG_BOOTDELAY 5 | |
| /* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */ | |
| /* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */ | |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */ | |
| #define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */ | |
| #define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */ | |
| #define CONFIG_IPADDR 10.0.0.100 | |
| #define CONFIG_SERVERIP 10.0.0.1 | |
| #define CONFIG_PREBOOT | |
| /*************************************************************** | |
| * defines if the console is stored in the environment | |
| ***************************************************************/ | |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* stdin, stdout and stderr are in evironment */ | |
| /*************************************************************** | |
| * defines if an overwrite_console function exists | |
| *************************************************************/ | |
| #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE | |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET | |
| /*************************************************************** | |
| * defines if the overwrite_console should be stored in the | |
| * environment | |
| **************************************************************/ | |
| #undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE | |
| /************************************************************** | |
| * loads config | |
| *************************************************************/ | |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ | |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ | |
| #define CONFIG_MISC_INIT_R | |
| /*********************************************************** | |
| * Miscellaneous configurable options | |
| **********************************************************/ | |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ | |
| #if defined(CONFIG_CMD_KGDB) | |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ | |
| #else | |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ | |
| #endif | |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ | |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ | |
| #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ | |
| #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 1 ... 12 MB in DRAM */ | |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ | |
| #define CONFIG_SYS_NS16550_SERIAL | |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 | |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() | |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ | |
| #define CONFIG_SYS_BASE_BAUD 691200 | |
| /* The following table includes the supported baudrates */ | |
| #define CONFIG_SYS_BAUDRATE_TABLE \ | |
| { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ | |
| 57600, 115200, 230400, 460800, 921600 } | |
| #define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ | |
| #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ | |
| /*----------------------------------------------------------------------- | |
| * PCI stuff | |
| *----------------------------------------------------------------------- | |
| */ | |
| #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ | |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ | |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ | |
| #define CONFIG_PCI /* include pci support */ | |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ | |
| #define CONFIG_PCI_HOST PCI_HOST_FORCE /* configure as pci-host */ | |
| #define CONFIG_PCI_PNP /* pci plug-and-play */ | |
| /* resource configuration */ | |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ | |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ | |
| #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ | |
| #define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ | |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ | |
| #define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ | |
| #define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ | |
| #define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ | |
| /*----------------------------------------------------------------------- | |
| * Start addresses for the final memory configuration | |
| * (Set up by the startup code) | |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 | |
| */ | |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 | |
| #define CONFIG_SYS_FLASH_BASE 0xFFF80000 | |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE | |
| #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ | |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ | |
| /* | |
| * For booting Linux, the board info and command line data | |
| * have to be in the first 8 MB of memory, since this is | |
| * the maximum mapped by the Linux kernel during initialization. | |
| */ | |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ | |
| /*----------------------------------------------------------------------- | |
| * FLASH organization | |
| */ | |
| #define CONFIG_SYS_UPDATE_FLASH_SIZE | |
| #define CONFIG_SYS_FLASH_PROTECTION | |
| #define CONFIG_SYS_FLASH_EMPTY_INFO | |
| #define CONFIG_SYS_FLASH_CFI | |
| #define CONFIG_FLASH_CFI_DRIVER | |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 | |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 | |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 | |
| /* | |
| * Init Memory Controller: | |
| */ | |
| #define FLASH_MAX_SIZE 0x00800000 /* 8MByte max */ | |
| #define FLASH_BASE_PRELIM 0xFF800000 /* open the flash CS */ | |
| /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */ | |
| #define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */ | |
| #define CONFIG_BOARD_EARLY_INIT_F | |
| /* Configuration Port location */ | |
| #define CONFIG_PORT_ADDR 0xF4000000 | |
| #define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000 | |
| /*----------------------------------------------------------------------- | |
| * Definitions for initial stack pointer and data area (in On Chip SRAM) | |
| */ | |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 | |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 | |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 | |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */ | |
| #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */ | |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) | |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET | |
| /*********************************************************************** | |
| * External peripheral base address | |
| ***********************************************************************/ | |
| #define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000 | |
| /*********************************************************************** | |
| * Last Stage Init | |
| ***********************************************************************/ | |
| #define CONFIG_LAST_STAGE_INIT | |
| /************************************************************ | |
| * Ethernet Stuff | |
| ***********************************************************/ | |
| #define CONFIG_PPC4xx_EMAC | |
| #define CONFIG_MII 1 /* MII PHY management */ | |
| #define CONFIG_PHY_ADDR 1 /* PHY address */ | |
| /************************************************************ | |
| * RTC | |
| ***********************************************************/ | |
| #define CONFIG_RTC_MC146818 | |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ | |
| /************************************************************ | |
| * IDE/ATA stuff | |
| ************************************************************/ | |
| #define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */ | |
| #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ | |
| #define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */ | |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */ | |
| #define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */ | |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */ | |
| #define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */ | |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */ | |
| #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ | |
| #undef CONFIG_IDE_LED /* no led for ide supported */ | |
| #define CONFIG_IDE_RESET /* reset for ide supported... */ | |
| #define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */ | |
| #define CONFIG_SUPPORT_VFAT | |
| /************************************************************ | |
| * ATAPI support (experimental) | |
| ************************************************************/ | |
| #define CONFIG_ATAPI /* enable ATAPI Support */ | |
| /************************************************************ | |
| * SCSI support (experimental) only SYM53C8xx supported | |
| ************************************************************/ | |
| #define CONFIG_SCSI_SYM53C8XX | |
| #define CONFIG_SYS_SCSI_MAX_LUN 8 /* number of supported LUNs */ | |
| #define CONFIG_SYS_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */ | |
| #define CONFIG_SYS_SCSI_MAX_DEVICE CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */ | |
| #define CONFIG_SYS_SCSI_SPIN_UP_TIME 2 | |
| /************************************************************ | |
| * Disk-On-Chip configuration | |
| ************************************************************/ | |
| #define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ | |
| #define CONFIG_SYS_DOC_SHORT_TIMEOUT | |
| #define CONFIG_SYS_DOC_SUPPORT_2000 | |
| #define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM | |
| /************************************************************ | |
| * DISK Partition support | |
| ************************************************************/ | |
| #define CONFIG_DOS_PARTITION | |
| #define CONFIG_MAC_PARTITION | |
| #define CONFIG_ISO_PARTITION /* Experimental */ | |
| /************************************************************ | |
| * Video support | |
| ************************************************************/ | |
| #define CONFIG_VIDEO /*To enable video controller support */ | |
| #define CONFIG_VIDEO_CT69000 | |
| #define CONFIG_CFB_CONSOLE | |
| #define CONFIG_VIDEO_LOGO | |
| #define CONFIG_CONSOLE_EXTRA_INFO | |
| #define CONFIG_VGA_AS_SINGLE_DEVICE | |
| #define CONFIG_VIDEO_SW_CURSOR | |
| #define CONFIG_VIDEO_ONBOARD /* Video controller is on-board */ | |
| /************************************************************ | |
| * USB support | |
| ************************************************************/ | |
| #define CONFIG_USB_UHCI | |
| #define CONFIG_USB_KEYBOARD | |
| #define CONFIG_USB_STORAGE | |
| /* Enable needed helper functions */ | |
| #define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */ | |
| /************************************************************ | |
| * Debug support | |
| ************************************************************/ | |
| #if defined(CONFIG_CMD_KGDB) | |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ | |
| #endif | |
| /************************************************************ | |
| * support BZIP2 compression | |
| ************************************************************/ | |
| #define CONFIG_BZIP2 1 | |
| /************************************************************ | |
| * Ident | |
| ************************************************************/ | |
| #define VERSION_TAG "released" | |
| #define CONFIG_ISO_STRING "MEV-10066-001" | |
| #define CONFIG_IDENT_STRING "\n(c) 2002 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG | |
| #endif /* __CONFIG_H */ |