| CONFIG_ARM=y | |
| CONFIG_SKIP_LOWLEVEL_INIT=y | |
| CONFIG_SYS_THUMB_BUILD=y | |
| CONFIG_ARCH_VF610=y | |
| CONFIG_TEXT_BASE=0x3f401000 | |
| CONFIG_SYS_MALLOC_LEN=0x0220000 | |
| CONFIG_NR_DRAM_BANKS=1 | |
| CONFIG_ENV_SIZE=0x20000 | |
| CONFIG_ENV_OFFSET=0x180000 | |
| CONFIG_DM_GPIO=y | |
| CONFIG_DEFAULT_DEVICE_TREE="vf610-twr" | |
| CONFIG_SYS_LOAD_ADDR=0x82000000 | |
| CONFIG_SYS_MEMTEST_START=0x80010000 | |
| CONFIG_SYS_MEMTEST_END=0x87c00000 | |
| CONFIG_HAS_BOARD_SIZE_LIMIT=y | |
| CONFIG_BOARD_SIZE_LIMIT=520192 | |
| CONFIG_BOOTDELAY=3 | |
| CONFIG_USE_BOOTCOMMAND=y | |
| CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi" | |
| CONFIG_SYS_CBSIZE=256 | |
| CONFIG_SYS_PBSIZE=276 | |
| CONFIG_LOGLEVEL=3 | |
| CONFIG_BOARD_EARLY_INIT_F=y | |
| CONFIG_HUSH_PARSER=y | |
| # CONFIG_CMDLINE_EDITING is not set | |
| # CONFIG_AUTO_COMPLETE is not set | |
| CONFIG_CMD_BOOTZ=y | |
| CONFIG_CMD_MEMTEST=y | |
| CONFIG_CMD_FUSE=y | |
| CONFIG_CMD_GPIO=y | |
| CONFIG_CMD_I2C=y | |
| CONFIG_CMD_MMC=y | |
| CONFIG_CMD_NAND_TRIMFFS=y | |
| # CONFIG_CMD_SETEXPR is not set | |
| CONFIG_CMD_DHCP=y | |
| CONFIG_CMD_MII=y | |
| CONFIG_CMD_PING=y | |
| CONFIG_CMD_FAT=y | |
| CONFIG_MTDIDS_DEFAULT="nand0=fsl_nfc" | |
| CONFIG_MTDPARTS_DEFAULT="mtdparts=fsl_nfc:128k(vf-bcb)ro,1408k(u-boot)ro,512k(u-boot-env),4m(kernel),512k(fdt),-(rootfs)" | |
| CONFIG_CMD_UBI=y | |
| CONFIG_OF_CONTROL=y | |
| CONFIG_ENV_OVERWRITE=y | |
| CONFIG_ENV_IS_IN_NAND=y | |
| CONFIG_ENV_RANGE=0x80000 | |
| CONFIG_ENV_RELOC_GD_ENV_ADDR=y | |
| CONFIG_VYBRID_GPIO=y | |
| CONFIG_DM_I2C=y | |
| CONFIG_SYS_I2C_MXC=y | |
| CONFIG_FSL_ESDHC_IMX=y | |
| CONFIG_MTD=y | |
| CONFIG_NAND_VF610_NFC=y | |
| CONFIG_SYS_NAND_ONFI_DETECTION=y | |
| CONFIG_SYS_NAND_BUSWIDTH_16BIT=y | |
| CONFIG_FEC_MXC=y | |
| CONFIG_MII=y | |
| CONFIG_PHYLIB=y | |
| CONFIG_PHY_MICREL=y | |
| CONFIG_PHY_MICREL_KSZ8XXX=y | |
| CONFIG_DM_SERIAL=y | |
| CONFIG_FSL_LPUART=y |